Engine

P0131 A/f Sensor 1

23steps
~138min
5/5difficulty
Done 0 of 23
DTC Description

DTC DETECTION LOGIC

To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal is not inordinately low.

The A/F signal computed by ECM from the A/F sensor 1 signal is constantly approx. 0 V.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P0131

A/F SENSOR1 (B1)

(O2 sensor circuit low voltage bank 1 sensor 1)
Diagnosis condition —
Signal (terminal) The A/F signal computed by ECM
Threshold The A/F signal computed by ECM from the A/F sensor 1 signal is constantly approx. 0 V
Diagnosis delay time —
P0151

A/F SENSOR1 (B2)

(O2 sensor circuit high voltage bank 2 sensor 1)
Diagnosis condition —
Signal (terminal) The A/F signal computed by ECM
Threshold The A/F signal computed by ECM from the A/F sensor 1 signal is constantly approx. 0 V
Diagnosis delay time —

POSSIBLE CAUSE

P0131

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

P0151

  • Harness or connectors (The A/F sensor 1 circuit is open or shorted.)

  • A/F sensor 1

FAIL-SAFE

Not applicable

DTC Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 10.5 V at idle.

>>

GO TO 2.

CHECK A/F SENSOR 1 FUNCTION

With CONSULT

  1. Start engine and warm it up to normal operating temperature.

  2. Select “A/F SEN1 (B1)” or “A/F SEN1 (B2)” in “DATA MONITOR” mode with CONSULT.

  3. Check “A/F SEN1 (B1)” or “A/F SEN1 (B2)” indication.

With GST

Follow the procedure “With CONSULT” above.

Is the indication constantly approx. 0 V?

YES>>

Proceed to Diagnosis Procedure.

NO>>

GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

  1. Turn ignition switch OFF, wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF, wait at least 10 seconds and then restart engine.

  4. Drive and accelerate Nissan Murano vehicle to more than 40 km/h within 20 seconds after restarting engine.

  5. Maintain the following conditions for approximately 20 consecutive seconds.

    ENG SPEED 1,000 - 3,200 rpm
    VHCL SPEED SE More than 40 km/h
    B/FUEL SCHDL 1.5 - 9.0 msec
    Selector lever Suitable position
  6. Check 1st trip DTC.

With GST

Follow the procedure “With CONSULT” above.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure.

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY

  1. Disconnect A/F sensor 1 harness connector.

  2. Turn ignition switch ON.

  3. Check the voltage between A/F sensor 1 harness connector and ground.

    DTCA/F sensor 1GroundVoltage
    BankConnectorTerminal
    P0131 1 F12 1 Ground Battery voltage
    P0151 2 F61 1

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

GO TO 2.

CHECK AIR FUEL RATIO (A/F) SENSOR 1 POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect IPDM E/R harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

DTCA/F sensor 1IPDM E/RContinuity
BankConnectorTerminalConnectorTerminal
P0131 1 F12 1 F19 52 Existed
P0151 2 F61 1 53

Is the inspection result normal?

YES>>

Perform the trouble diagnosis for power supply circuit.

NO>>

Repair or replace error-detected parts.

CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT

  1. Turn ignition switch OFF.

  2. Disconnect ECM harness connector.

  3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector .

    DTCA/F sensor 1ECMContinuity
    BankConnectorTerminalConnectorTerminal
    P0131 1 F12 3 F79 66 Existed
    4 67
    P0151 2 F61 3 76
    4 77
  4. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

    DTCA/F sensor 1GroundContinuity
    BankConnectorTerminal
    P0131 1 F12 3 Ground Not existed
    4
    P0151 2 F61 3
    4
    DTCECMGroundContinuity
    ConnectorTerminal
    P0131 F79 66 Ground Not existed
    67
    P0151 76
    77
  5. Also check harness for short to power.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Repair open circuit, short to ground or short to power in harness or connectors.