Engine

P052a Intake Valve Timing Control

41steps
~246min
5/5difficulty
Done 0 of 41
DTC Description

DTC DETECTION LOGIC

There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions.

DTC

CONSULT screen terms

(Trouble diagnosis content)
DTC detection condition
P052A

CAMSHAFT POSITION TIMING B1

(Cold start “A” camshaft position timing over-advanced bank 1)
Diagnosis condition —
Signal (terminal) —
Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions
Diagnosis delay time —
P052B

CAMSHAFT POSITION TIMING B1

(Cold start “A” camshaft position timing over-retarded bank 1)
Diagnosis condition —
Signal (terminal) —
Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions
Diagnosis delay time —
P052C

CAMSHAFT POSITION TIMING B2

(Cold start “A” camshaft position timing over-advanced bank 2)
Diagnosis condition —
Signal (terminal) —
Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions
Diagnosis delay time —
P052D

CAMSHAFT POSITION TIMING B2

(Cold start “A” camshaft position timing over-retarded bank 2)
Diagnosis condition —
Signal (terminal) —
Threshold There is a gap between the target phase angle and the detected phase angle when the engine is operating in cold conditions
Diagnosis delay time —

POSSIBLE CAUSE

DTC P052A

  • Crankshaft position sensor

  • Camshaft position sensor

  • Intake valve timing control solenoid valve

  • Intake valve timing intermediate lock control solenoid valve

  • Accumulation of debris to the signal pick-up portion of the camshaft

  • Timing chain installation

  • Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve

DTC P052B

  • Crankshaft position sensor

  • Camshaft position sensor

  • Intake valve timing control solenoid valve

  • Intake valve timing intermediate lock control solenoid valve

  • Accumulation of debris to the signal pick-up portion of the camshaft

  • Timing chain installation

  • Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve

DTC P052C

  • Crankshaft position sensor

  • Camshaft position sensor

  • Intake valve timing control solenoid valve

  • Intake valve timing intermediate lock control solenoid valve

  • Accumulation of debris to the signal pick-up portion of the camshaft

  • Timing chain installation

  • Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve

DTC P052D

  • Crankshaft position sensor

  • Camshaft position sensor

  • Intake valve timing control solenoid valve

  • Intake valve timing intermediate lock control solenoid valve

  • Accumulation of debris to the signal pick-up portion of the camshaft

  • Timing chain installation

  • Foreign matter caught in the intake valve timing control (or intermediate lock control) solenoid valve

FAIL-SAFE

Engine operating condition in fail-safe mode
Fail safe modeNissan Murano Vehicle behavior
Intake valve timing intermediate lock control —
DTC Confirmation Procedure

CHECK DTC PRIORITY

If DTC P052A, P052B, P052C and P052D is displayed with DTC P0075 or P0081, first perform the confirmation procedure for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable.

  • DTC P0075: Refer to DTC Description.

  • DTC P0081: Refer to DTC Description.

NO>>

GO TO 2.

PRECONDITIONING

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is 10 V or more at idle.

With CONSULT

  1. Turn ignition switch OFF and wait at least 10 seconds.

  2. Turn ignition switch ON.

  3. Turn ignition switch OFF and wait at least 10 seconds.

  4. Turn ignition switch ON.

  5. On the CONSULT screen, select “ENGINE” >> “DATA MONITOR” >> “COOLAN TEMP/S”.

  6. Check “COOLAN TEMP/S” indication value.

With GST

Follow the procedure “With CONSULT” above.

Is the value of “COOLAN TEMP/S”−5 °C and 45 °C?

YES>>

GO TO 3.

NO>>

Warm up the engine until the value of “COOLAN TEMP/S” indicates −5 °C and 45 °C. And then GO TO 3.

NO>>

Cool the engine down to the value of “COOLAN TEMP/S” indicates −5 °C and 45 °C. And then GO TO 3.

PERFORM DTC CONFIRMATION PROCEDURE-I

  1. Turn ignition switch OFF and wait at 10 seconds.

  2. Turn ignition switch ON.

  3. Set the selector lever in N range.

  4. Start the engine and let it idle for 20 seconds or more.

  5. Check 1st trip DTC.

Is 1st trip DTC detected?

YES>>

Proceed to Diagnosis Procedure

NO>>

To check malfunction symptom before repair: Refer to Intermittent Incident.

NO>>

Confirmation after repair: INSPECTION END

Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P052A, P052B, P052C and P052D is displayed with DTC P0075 or P0081, first perform the confirmation procedure for DTC UXXXX or P0607.

Is applicable DTC detected?

YES>>

Perform diagnosis of applicable.

  • DTC P0075: Refer to DTC Description.

  • DTC P0081: Refer to DTC Description.

NO>>

GO TO 2.

INSPECTION START

With CONSULT>>

GO TO 3.

Without CONSULT>>

GO TO 4.

CHECK VTC POSITION

With CONSULT

  1. Turn ignition switch ON.

  2. On the CONSULT screen, select “ENGINE” >> “DATA MONITOR” >> “COOLAN TEMP/S”.

  3. Check that the “COOLAN TEMP/S” indication value is between −5 °C and 45 °C.

  4. Start engine and wait at least 5 seconds.

  5. On the CONSULT screen, select “ENGINE” >> “DATA MONITOR” >> “INT/V TIM (B1)”.

  6. Check that the data monitor item indicates as follows:

    ItemValue (°CA)
    INT/V TIM (B1) 10 ± 2
    INT/V TIM (B2) 10 ± 2

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

GO TO 5.

CHECK OIL PRESSURE WARNING LAMP

  1. Start engine.

  2. Check that oil pressure warning lamp is not illuminated.

Is oil pressure warning lamp illuminated?

YES>>

Refer to Inspection.

NO>>

GO TO 6.

CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE

Perform Component Inspection of the intake valve timing intermediate lock control solenoid valve. Refer to Component Inspection (Intake Valve Timing Intermediate Lock Control Solenoid Valve).

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace error-detected parts.

CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE

Perform Component Inspection of the intake valve timing control solenoid valve. Refer to Component Inspection (Intake Valve Timing Control Solenoid Valve).

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace error-detected parts.

CHECK CRANKSHAFT POSITION SENSOR

Perform Component Inspection of the crankshaft position sensor. Refer to Component Inspection (Crankshaft Position sensor).

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace error-detected parts.

CHECK CAMSHAFT POSITION SENSOR

Perform Component Inspection of the camshaft position sensor. Refer to Component Inspection (Crankshaft Position sensor).

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Repair or replace error-detected parts.

CHECK CAMSHAFT (INTAKE)

Check the following.

  1. Accumulation of debris on the signal plate of camshaft front end

  2. Chipping signal plate of camshaft front end

Is the inspection result normal?

YES>>

GO TO 10.

NO>>

Remove debris and clean the signal plate of camshaft front end or replace camshaft. Refer to Removal and Installation.

CHECK TIMING CHAIN INSTALLATION

Check service records for any recent repairs that may cause timing chain misalignment.

Are there any service records that may cause timing chain misalignment?

YES>>

Check timing chain installation. Refer to Removal and Installation.

NO>>

GO TO 11.

CHECK LUBRICATION CIRCUIT

Perform “Inspection of Camshaft Sprocket (INT) Oil Groove”. Refer to Inspection after Installation.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Clean lubrication line.

Component Inspection (Intake Valve Timing Control Solenoid Valve)

CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I

  1. Turn ignition switch OFF.

  2. Disconnect intake valve timing control solenoid valve harness connector.

  3. Check resistance between intake valve timing control solenoid valve terminals as per the following.

    Intake valve timing control solenoid valve

    Condition

    Resistance
    +−
    Terminal
    1 2 Temperature 20 °C 7.0 – 7.8 Ω
    1 Ground

    ∞

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning intake valve timing control solenoid valve. Refer to Exploded View.

CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II

  1. Remove intake valve timing control solenoid valve. Refer to Exploded View.

  2. Provide 12 V DC between intake valve timing control solenoid valve terminals 1 and 2, and then interrupt it. Check that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning intake valve timing control solenoid valve. Refer to Exploded View.

Component Inspection (Intake Valve Timing Intermediate Lock Control Solenoid Valve)

CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-I

  1. Turn ignition switch OFF.

  2. Disconnect intake valve timing intermediate lock control solenoid valve harness connector.

  3. Check resistance between intake valve timing intermediate lock control solenoid valve terminals as per the following.

    Intake valve timing intermediate lock control solenoid valve

    Condition

    Resistance
    +−
    Terminal
    1 2 Temperature 20 °C 7.0 – 7.8 Ω
    1 Ground

    ∞

    (Continuity should not exist)
    2

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace malfunctioning intake valve timing intermediate lock control solenoid valve. Refer to Exploded View.

CHECK INTAKE VALVE TIMING INTERMEDIATE LOCK CONTROL SOLENOID VALVE-II

  1. Remove intake valve timing intermediate lock control solenoid valve. Refer to Exploded View.

  2. Provide 12 V DC between intake valve timing intermediate lock control solenoid valve terminals 1 and 2, and then interrupt it. Check that the plunger moves as shown in the figure.

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace malfunctioning intake valve timing intermediate lock control solenoid valve. Refer to Exploded View.

Component Inspection (Crankshaft Position sensor)

CHECK CRANKSHAFT POSITION SENSOR (POS)-1

  1. Turn ignition switch OFF.

  2. Loosen the fixing bolt of the sensor.

  3. Disconnect crankshaft position sensor (POS) harness connector.

  4. Remove the sensor.

  5. Visually check the sensor for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace crankshaft position sensor (POS). Refer to Exploded View.

CHECK CRANKSHAFT POSITION SENSOR (POS)-2

Check the resistance between crankshaft position sensor (POS) terminals as per the following.

Crankshaft position sensor (POS)Resistance [at 25 °C]
+−
Terminal (Polarity)
1 2

Except 0 or ∞Ω

3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace crankshaft position sensor (POS). Refer to Exploded View.

Component Inspection (Camshaft position sensor)

CHECK CAMSHAFT POSITION SENSOR (PHASE)-1

  1. Turn ignition switch OFF.

  2. Loosen the fixing bolt of the sensor.

  3. Disconnect camshaft position sensor (PHASE) harness connector.

  4. Remove the sensor. Refer to Exploded View.

  5. Visually check the sensor for chipping.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Replace camshaft position sensor (PHASE).

CHECK CAMSHAFT POSITION SENSOR (PHASE)-2

Check the resistance camshaft position sensor (PHASE) terminals as per the following.

Camshaft position sensor (PHASE)Resistance [ Ω at 25 °C]
+−
Terminals (Polarity)
1 2 Except 0 or ∞
3
2 3

Is the inspection result normal?

YES>>

INSPECTION END

NO>>

Replace camshaft position sensor (PHASE). Refer to Exploded View.