Exterior Lighting

Daytime Running Light Relay Circuit

~4min read

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Check the fuses for the circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to the registration section.*1

    Click here

    • *1: with Smart Key System

PROCEDURE

  1. INSPECT OPERATION (TAIL LIGHTS)

(a) Check that the tail lights operate normally.

OK:

The tail lights operate normally.

NG

REFER TO SYMPTOM TROUBLESHOOTING TABLE

OK
  1. PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test by following the Techstream instructions.

Body Electrical > Main Body > Active Test

Tester display

Item

Control Range

Diagnostic Note

Daytime Running Light

Daytime Running Lights

ON or OFF

-

Body Electrical > Main Body > Active Test

Daytime Running Light

OK:

The daytime running lights come on.

OK

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

NG
  1. INSPECT INTEGRATION RELAY NO. 1 (P-CON RELAY)

(a) Remove integration relay No. 1 from the No. 1 engine room relay block.

Click here

(b) Inspect integration relay No. 1.

Click here

OK:

Integration relay No. 1 operates normally.

NG

REPLACE INTEGRATION RELAY NO. 1

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (INTEGRATION RELAY NO. 1 (P-CON RELAY) - BATTERY)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

1B-9 - Body ground

Always

11 à 14 V

1B-11 - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (INTEGRATION RELAY NO. 1 - LH HEADLIGHT ASSEMBLY AND RH HEADLIGHT ASSEMBLY)

(a) Disconnect the A11 connector from the LH headlight assembly.

(b) Disconnect the A29 connector from the RH headlight assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

1B-10 - A11-2 (B)

Always

Below 1 Ω

1B-10 - A29-2 (B)

Always

Below 1 Ω

1B-10 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (INTEGRATION RELAY NO. 1 - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 3F connector from the instrument panel junction block assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

1B-12 - 3F-28

Always

Below 1 Ω

1B-12 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

(a) Remove the instrument panel junction block assembly.

Click here

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

*a

Component without wire harness connected

(instrument panel junction block assembly)

-

-

Standard resistance:

Tester Connection

Condition

Specified Condition

3F-28 - MB-25 (DRLE)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY