Body Electrical System

Fuses And Relays

36steps
~216min
4/5difficulty
Done 0 of 36

Contents:

Engine Room Junction Block Removal and Installation

Removal

Engine Room PCB Block
  1. Disconnect the negative ( - ) battery terminal.
  2. Disconnect the engine room PCB block connector (A).
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Removal and Installation / Removal illustration
  3. Remove the engine room PCB block (A) by pulling the hooks in the direction of the arrows.
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Removal and Installation / Removal illustration
  4. Disconnect the engine room PCB block connectors (A).
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Engine Room Junction Block Inspection

Inspection

Power Relay Inspection (Type A) Check for continuity between the terminals.
  1. After supplying power between terminal No. 85 and 86, check that there is continuity between terminal No. 30 and 87.
  2. After supplying power between terminal No. 85 and 86, check that there is no continuity between terminal No. 30 and 87.
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
    Terminal Operate
    Power ON Power OFF
    30 - 87 Continuity -
  3. After supplying power between terminal No. 86 and 85, check that there is continuity between terminal No. 87 and 30.
  4. After supplying power between terminal No. 86 and 85, check that there is no continuity between terminal No. 87 and 30.
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
    Terminal Operate
    Power ON Power OFF
    30 - 87 Continuity -
  5. Check for separation of fuse holder and check that the holder is tightly holding the fuse.
  6. Check that each fuse circuit has the exact fuse capacity.
  7. Check the fuses for any damage.
    Note
    If a fuse is to be replaced, be sure to use a new fuse of the same capacity.
  8. Disconnect the negative ( - ) battery terminal.
  9. Remove the terminals (A) after removing the nuts.
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
  10. Remove the multi-fuse (A) by pulling the hooks in the direction of the arrows.
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
  11. Remove the multi-fuse (B) by pulling the hooks in the direction of the arrows and then remove the multi-fuse (C).
    Body Electrical System — Fuses And Relays / Engine Room Junction Block / Inspection illustration
  12. Check the multi-fuses for any damage.
    Information
    Use the multi-fuse of the exact fuse capacity.
Power Relay (Type B) Check for continuity between the terminals. Fuse Multi-Fuse

Integrated Central Control Unit (ICU) Description and Operation

Description

The Integrated Central Control Unit (ICU) is the next-generation model of the Integrated Gateway and Power Control Module (IGPM).
Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / Description illustration

System Block Diagram

Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / System Block Diagram illustration

ICU Operating Function

Item Function
Function Switch Input Receives switch inputs and then sends the switch status to each module via CAN message.
Lamp control Controls lamp with the IPS by receiving command from IBU via CAN message.
Internal relay control Controls internal relay by receiving command from IBU via CAN message.
External relay control Controls external relay by receiving command from IBU via CAN message.
Parasitic current shut-off system The system automatically shuts off the power to be provided with components for reducing useless parasitic current according to the vehicle operating conditions such as shipment and long-term parking.
Troubleshooting Diagnose status of loads controlled by IPS.
Gateway Transmits signals among the modules connected to the different networks in the vehicle.

※The ICU does not determine logic, it is operated only by CAN commands from other modules. ▶ Self-Logic Function : Hazard lamp, stop lamp, steering wheel heater Switch Input
  1. Operating Function ▶ Hazard lamp switch, seat belt switch, tailgate switch, door switch, etc.
  2. Operating Description
    1. Determined switch operation status
    2. Switch status messages are sent to other modules (IBU, DAU, PSM, etc.) via CAN communication.
      Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / ICU Operating Function illustration
  3. Operating Function ▶ Headlamp low/high, turn signal lamp, DRL lamp, internal/external tail lamp, stop lamp, etc.
  4. Operating Description
    1. Lamp ON/OFF operation via CAN message of IBU
    2. Detects current flowing through the lamp via IPS
    3. Lamp OFF when over-current detection (PCL control : Shut-off current of lamp if reference current is exceeded)
      Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / ICU Operating Function illustration
      ※ IPS can replace fuse and relay functions by applying semi-conductors, and there is also a circuit break function to protect devices from overheating/overcurrent.
  5. Operating Function ▶ Burglar alarm horn, tailgate, power window, etc
  6. Operating Description
    1. Relay ON/OFF operation via CAN message of IBU
      Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / ICU Operating Function illustration
  7. Operating Function ▶ Headlamp high solenoid, rear fog, rear glass defogger, etc.
  8. Operating Description
    1. Relay ON/OFF operation via CAN message of IBU
      Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / ICU Operating Function illustration
  9. Operating Description
    1. If the CAN and switch inputs are absent for a long time, the power output is turn off sequentially to prevent battery discharge.
    2. If a CAN or switch input is received while the parasitic current shut-off system is operating, the system is disabled for normal operation.
      Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Description and Operation / ICU Operating Function illustration
IPS Lamp control Internal relay control External relay control Parasitic current shut-off system

Integrated Central Control Unit (ICU) Inspection

Inspection

fuse
  1. Check for separation of fuse holder and check that the holder is tightly holding the fuse.
  2. Check that each fuse circuit has the exact fuse capacity.
  3. Check the fuses for any damage.
    Note
    If a fuse is to be replaced, be sure to use a new fuse of the same capacity.

Integrated Central Control Unit (ICU) Removal and Installation

Removal

  1. Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel")
  2. Disconnect the integrated central control unit (ICU) connectors (A).
    Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Removal and Installation / Removal illustration
  3. Remove the Integrated Central Control Unit (ICU) (A) after removing the bolt and nuts.
    Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Removal and Installation / Removal illustration
  4. Disconnect the integrated central control unit (ICU) connectors (A).
    Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Removal and Installation / Removal illustration
  5. Remove the wiring clip (A).
    Body Electrical System — Fuses And Relays / Integrated Central Control Unit (ICU) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.

Integrated Circuit Module (ICM) Removal and Installation

Removal

  1. Remove the crash pad lower panel. (Refer to Body - "Crash Pad Lower Panel")
  2. Disconnect the Integrated Circuit Module (ICM) connectors (A).
    Body Electrical System — Fuses And Relays / Integrated Circuit Module (ICM) / Removal and Installation / Removal illustration
  3. Remove the Integrated Circuit Module (ICM) (A) after removing the nuts.
    Body Electrical System — Fuses And Relays / Integrated Circuit Module (ICM) / Removal and Installation / Removal illustration

Installation

  1. Install in reverse order of removal.