Black Out Tape(for Rear Door)
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*1 |
REAR DOOR ARMREST COVER SUB-ASSEMBLY |
*2 |
REAR DOOR TRIM ASSEMBLY COVER |
*3 |
REAR DOOR TRIM BOARD SUB-ASSEMBLY |
*4 |
REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL |
ILLUSTRATION
*1 |
REAR DOOR GLASS RUN |
*2 |
REAR DOOR GLASS SUB-ASSEMBLY |
*3 |
REAR DOOR INNER GLASS WEATHERSTRIP |
*4 |
REAR DOOR NO. 1 TRIM BRACKET |
*5 |
REAR DOOR NO. 2 SERVICE HOLE COVER |
*6 |
REAR DOOR REAR GUIDE SEAL |
*7 |
REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY |
*8 |
REAR DOOR SERVICE HOLE COVER |
*9 |
REAR DOOR WEATHERSTRIP |
*10 |
HOLE PLUG |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
NO. 1 BLACK OUT TAPE |
*2 |
NO. 2 BLACK OUT TAPE |
*3 |
NO. 3 BLACK OUT TAPE |
*4 |
REAR DOOR CHECK ASSEMBLY |
*5 |
REAR DOOR FRAME GARNISH |
*6 |
REAR DOOR WEATHERSTRIP |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent |
★ |
Precoated part |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REPAIR INSTRUCTION
Click here ![]()
3. INSTALL NO. 2 BLACK OUT TAPE
(a) Refer to the illustration to position a new No. 2 black out tape.
*A |
Lower Side |
*B |
LH Side |
*C |
RH Side |
- |
- |
*1 |
Rear Door Weatherstrip |
- |
- |
*a |
Edge of Curved Surface |
*b |
Straight |
*c |
Triangle |
- |
- |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
5.0 mm (0.197 in.) |
B |
2.5 mm (0.0984 in.) |
C |
1.0 mm (0.0394 in.) |
- |
- |
(b) Remove the release paper and apply the No. 2 black out tape.
4. INSTALL NO. 3 BLACK OUT TAPE
(a) Refer to the illustration to position a new No. 3 black out tape.
*A |
Front Side |
*B |
LH Side |
*C |
RH Side |
- |
- |
*a |
Rib of Door Frame Garnish |
*b |
Edge of Curved Surface |
*c |
Straight |
*d |
Triangle |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
8.5 mm (0.335 in.) |
B |
1.0 mm (0.0394 in.) |
C |
2.5 mm (0.0984 in.) |
- |
- |
(b) Remove the release paper and apply the No. 3 black out tape.
5. INSTALL NO. 1 BLACK OUT TAPE
(a) Refer to the illustration to position a new No. 1 black out tape.
*A |
Upper Side |
*B |
LH Side |
*C |
RH Side |
- |
- |
*1 |
Rear Door Weatherstrip |
- |
- |
*a |
Rib of Door Frame Garnish |
*b |
Edge of Curved Surface |
*c |
Straight |
*d |
Triangle |
Standard Measurement:
Area | Measurement | Area | Measurement |
|---|---|---|---|
A |
3.0 mm (0.118 in.) |
B |
5.0 mm (0.197 in.) |
C |
-1.0 to 1.0 mm (-0.0394 to 0.0394 in.) |
D |
1.0 mm (0.0394 in.) |
E |
1.2 mm (0.0472 in.) |
F |
1.0 mm (0.0394 in.) |
(b) Remove the release paper and apply the No. 1 black out tape.
6. INSTALL REAR DOOR FRAME GARNISH
Click here ![]()
7. INSTALL REAR DOOR WEATHERSTRIP
Click here ![]()
8. INSTALL REAR DOOR CHECK ASSEMBLY
Click here ![]()
9. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
10. INSTALL REAR DOOR REAR GUIDE SEAL
Click here ![]()
11. CONNECT REAR DOOR WEATHERSTRIP
Click here ![]()
12. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
13. INSTALL REAR DOOR GLASS RUN
Click here ![]()
14. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
15. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
16. INSTALL REAR DOOR SERVICE HOLE COVER
Click here ![]()
17. INSTALL REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
18. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
19. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
20. INSTALL REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
21. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
22. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
23. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
24. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
25. INSPECT POWER WINDOW OPERATION
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
|
Initialize power window control system |
|
|
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
5. REMOVE REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
8. REMOVE REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
9. REMOVE REAR DOOR SERVICE HOLE COVER
Click here ![]()
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
12. REMOVE REAR DOOR GLASS RUN
Click here ![]()
13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
14. DISCONNECT REAR DOOR WEATHERSTRIP
Click here ![]()
15. REMOVE REAR DOOR REAR GUIDE SEAL
Click here ![]()
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
17. REMOVE REAR DOOR CHECK ASSEMBLY
Click here ![]()
18. REMOVE REAR DOOR WEATHERSTRIP
Click here ![]()
19. REMOVE REAR DOOR FRAME GARNISH
Click here ![]()
20. REMOVE NO. 1 BLACK OUT TAPE
HINT:
When removing the No. 1 black out tape, heat the vehicle body and No. 1 black out tape using a heat light.
Heating TemperatureItem | Temperature |
|---|---|
No. 1 Black Out Tape and Vehicle Body |
40 to 60 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 1 black out tape and vehicle body.
(b) Pull back on one of the ends of the No. 1 black out tape to remove it. HINT: When pulling on the No. 1 black out tape, pull it parallel to the vehicle body. |
![]() |
21. REMOVE NO. 3 BLACK OUT TAPE
HINT:
When removing the No. 3 black out tape, heat the vehicle body and No. 3 black out tape using a heat light.
Heating TemperatureItem | Temperature |
|---|---|
No. 3 Black Out Tape and Vehicle Body |
40 to 60 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 3 black out tape and vehicle body.
(b) Pull back on one of the ends of the No. 3 black out tape to remove it. HINT: When pulling on the No. 3 black out tape, pull it parallel to the vehicle body. |
![]() |
22. REMOVE NO. 2 BLACK OUT TAPE
HINT:
When removing the No. 2 black out tape, heat the vehicle body and No. 2 black out tape using a heat light.
Heating TemperatureItem | Temperature |
|---|---|
No. 2 Black Out Tape and Vehicle Body |
40 to 60 °C |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
*a |
Heated Part |
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the No. 2 black out tape and vehicle body.
(b) Pull back on one of the ends of the No. 2 black out tape to remove it. HINT: When pulling on the No. 2 black out tape, pull it parallel to the vehicle body. |
![]() |





