Wiper And Washer System(for Hv Model)
How To Proceed With Troubleshooting
HINT:
- Use the following procedure to troubleshoot the wiper and washer system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
READ OUT AND SAVE OPERATION HISTORY
NOTICE:
- If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before operation history has been read out and saved, the operation history information could be lost.
- The function "Read operation history" uses the current system time setting inside the Techstream and the time counter inside the controlling ECU to calculate the timings shown in the operation history. For this reason, before reading out the operation history, first make sure that the Techstream system clock is accurately set to the current time.
(a) Read out and save operation history using the Techstream.
Click here ![]()
Operation History
|
PRE-CHECK
(a) Measure the auxiliary battery voltage with power switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
(a) Using the Techstream, check for CAN communication system DTCs.
Click here ![]()
Result | Proceed to |
|---|---|
CAN DTCs are not output |
A |
CAN DTCs are output |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK FOR DTC*
(a) Check for DTCs.
Body Electrical > Wiper > Trouble Codes Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTCs are output |
B |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
PROBLEM SYMPTOMS TABLE
(a) Refer to Problem Symptoms Table.
Click here ![]()
Result | Proceed to |
|---|---|
Fault is not listed in Problem Symptoms Table |
A |
Fault is listed in Problem Symptoms Table |
B |
| B | GO TO PROBLEM SYMPTOMS TABLE |
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Operation Check.
Click here ![]()
(b) Data List / Active Test
Click here ![]()
(c) Terminals of ECU
Click here ![]()
(d) Fail-safe Chart
Click here ![]()
(e) Inspection
(f) On-vehicle inspection
|
ADJUST, REPAIR OR REPLACE
|
CONFIRMATION TEST
| NEXT | END |
Parts Location
PARTS LOCATION
ILLUSTRATION
*1 |
WINDSHIELD WIPER MOTOR ASSEMBLY |
*2 |
LEVEL WARNING SWITCH ASSEMBLY |
*3 |
WINDSHIELD WASHER MOTOR AND PUMP ASSEMBLY |
*4 |
NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - WIPER FUSE - WIPER RELAY - WASHER RELAY |
ILLUSTRATION
*1 |
STEERING WHEEL SWITCH HOUSING |
*2 |
WINDSHIELD WIPER SWITCH ASSEMBLY |
*3 |
STEERING SENSOR |
*4 |
COMBINATION METER ASSEMBLY |
*5 |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
*6 |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - WASHER FUSE |
*7 |
DLC3 |
- |
- |
Precaution
PRECAUTION
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.
System Name | See Procedure |
|---|---|
Lane Departure Alert System (w/ Steering Control) |
|
Intelligent Clearance Sonar System |
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Pre-collision System |
|
Lighting System (for HV Model with Cornering Light) |
PRECAUTION FOR WASHER NOZZLE ADJUSTMENT
(a) Do not clean or adjust the washer nozzle with a safety pin, etc. because:
(1) The washer nozzle tip is made of resin and may be damaged.
(2) Adjustment is not necessary for this spray type washer nozzle. If it is necessary to change the nozzle angle, replace the washer nozzle with one that has a different nozzle angle.
Click here ![]()
(b) If the washer nozzle is clogged with wax, etc., remove it and clean the nozzle hole with a soft resin brush or other cleaning tool.
System Description
SYSTEM DESCRIPTION
FRONT WIPER AND WASHER CONTROL FUNCTION
Control/Function | Description |
|---|---|
Wiper speed regulation |
Maintains the default speed of the wipers even when the supply voltage or resistance changes. |
Wiper speed HI to LO transition control |
Smoothly controls the change in speed of the wipers when the wiper speed is changed from HI to LO. |
Service position control |
Stops the front wipers at the top of their stroke when the windshield wiper switch assembly is held in the MIST position for 2 seconds or more within approximately 45 seconds after the power switch is turned off. HINT:
|
Engine hood interference damage reduction function |
|
Self-locking control |
Holds the wipers in the park position when the power switch is on (IG). |
Protection mode |
|
MIST function |
Operates the wipers in LO when the windshield wiper switch assembly is held in the MIST position. |
Vehicle speed sensing type adjustable intermittent wiper control |
Controls the delay of the front wipers when the windshield wiper switch assembly is in the INT position. HINT:
|
Washer cooperation |
NOTICE: If the washer switch is operated for approximately 40 seconds or more, operation of the windshield washer motor and pump assembly is stopped to prevent burnout, and the front wipers are returned to the park position. |
Drip prevention wiper function |
Approximately 3 seconds after washer cooperation completes, operates the front wipers for 1 cycle to remove any remaining washer fluid. HINT: This function only operates when the vehicle is stationary and will stop operating at a vehicle speed of approximately 5 km/h or more. |
Vehicle stopped wiper control |
If the vehicle is stopped and the windshield wiper switch assembly is moved to the LO position, the front wipers will operate in LO for 3 cycles and then at a 2.5 second interval. |
- *: Function that allows the front wiper arms to be folded back such as when replacing the wiper rubber.
OTHER FUNCTIONS
Control/Function | Description |
|---|---|
Washer fluid level low warning |
Displays "Windshield Washer Fluid Low" on the multi-information display in the combination meter assembly when the washer fluid level is low. |
Wiper system warning |
Displays "Wiper System Malfunction Visit Your Dealer" on the multi-information display in the combination meter assembly when the wiper and washer system is malfunctioning. |
System Diagram
SYSTEM DIAGRAM
FRONT WIPER AND WASHER SYSTEM
WASHER FLUID LEVEL WARNING SYSTEM

