Fuel Lid Opener System(for Hv Model)
Data List / Active Test
DATA LIST / ACTIVE TEST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
DATA LIST
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List.
(e) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Fuel Filler Opener |
Fuel lid lock with motor assembly status |
OFF or ON |
OFF: Fuel lid lock with motor assembly not operating ON: Fuel lid lock with motor assembly operating |
- |
Fuel Lid SW |
Fuel lid opener switch status |
Close or Open |
Close: Fuel lid opener switch not pushed Open: Fuel lid opener switch pushed |
- |
Fuel Lid Sensor SW |
Fuel lid courtesy switch status |
Close or Open |
Close: Fuel lid closed Open: Fuel lid open |
- |
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
ACTIVE TEST
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Powertrain > Engine > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Activate the Fuel Filler Opener |
Fuel lid lock with motor assembly |
OFF/ON |
- |
Fuel Lid Opener does not Operate
DESCRIPTION
When the fuel lid opener switch is pushed, a fuel lid opener switch signal is sent to the ECM. The ECM turns on the FUEL OPN relay and EFI-MAIN relay, and the fuel lid lock with motor assembly opens the fuel lid. When the fuel lid is open, a fuel lid courtesy switch signal is output from the fuel lid lock with motor assembly.
WIRING DIAGRAM
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
CHECK FOR DTC (SFI SYSTEM)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Check for DTCs.
Powertrain > Engine > Trouble CodesOK:
SFI system DTCs are not output.
| NG | GO TO SFI SYSTEM |
|
PERFORM ACTIVE TEST USING TECHSTREAM (Activate the Fuel Filler Opener)
(a) Enter the following menus: Powertrain / Engine / Active Test.
(b) Perform the Active Test according to the display on the Techstream.
Powertrain > Engine > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Activate the Fuel Filler Opener |
Fuel lid lock with motor assembly |
OFF/ON |
- |
Activate the Fuel Filler Opener
OK:
The fuel lid lock with motor assembly operates normally.
| NG | GO TO STEP 9 |
|
READ VALUE USING TECHSTREAM (Fuel Lid SW)
(a) Enter the following menus: Powertrain / Engine / Data List.
(b) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Fuel Lid SW |
Fuel lid opener switch status |
Close or Open |
Close: Fuel lid opener switch not pushed Open: Fuel lid opener switch pushed |
- |
Fuel Lid SW
OK:
The Techstream display changes correctly in response to the operation of the fuel lid opener switch.
| NG | GO TO STEP 7 |
|
READ VALUE USING TECHSTREAM (Fuel Lid Sensor SW)
(a) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Fuel Lid Sensor SW |
Fuel lid courtesy switch status |
Close or Open |
Close: Fuel lid closed Open: Fuel lid open |
- |
Fuel Lid Sensor SW
OK:
The Techstream display changes correctly in response to the operation of the fuel lid courtesy switch (fuel lid lock with motor assembly).
| OK | REPLACE ECM |
|
INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
(a) Remove the fuel lid lock with motor assembly.
Click here ![]()
(b) Inspect the fuel lid lock with motor assembly. (Fuel lid courtesy switch)
Click here ![]()
| NG | REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - ECM)
(a) Disconnect the A19 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
P4-3 (B) - A19-31 (LIDO) |
Always |
Below 1 Ω |
P4-3 (B) or A19-31 (LIDO) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT FUEL LID OPENER SWITCH
(a) Remove the fuel lid opener switch.
Click here ![]()
(b) Inspect the fuel lid opener switch.
Click here ![]()
| NG | REPLACE FUEL LID OPENER SWITCH |
|
CHECK HARNESS AND CONNECTOR (FUEL LID OPENER SWITCH - ECM AND BODY GROUND)
(a) Disconnect the A19 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G25-5 (IG) - A19-38 (FUEL) |
Always |
Below 1 Ω |
G25-5 (IG) or A19-38 (FUEL) - Body ground |
Always |
10 kΩ or higher |
G25-2 (E) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT FUEL LID LOCK WITH MOTOR ASSEMBLY
(a) Remove the fuel lid lock with motor assembly.
Click here ![]()
(b) Inspect the fuel lid lock with motor assembly. (Motor operation)
Click here ![]()
| NG | REPLACE FUEL LID LOCK WITH MOTOR ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EFI-MAIN RELAY AND AUXILIARY BATTERY)
(a) Disconnect the 4F instrument panel junction block assembly connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4F-7 - Body ground |
Power switch on (IG) |
11 to 14 V |
4F-30 - Body ground |
Power switch on (IG) |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECM)
(a) Disconnect the A19 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4F-20 - A19-44 (FREL) |
Always |
Below 1 Ω |
4F-20 or A19-44 (FREL) - Body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (FUEL LID LOCK WITH MOTOR ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-28 - P4-1 (B) |
Always |
Below 1 Ω |
4H-28 or P4-1 (B) - Body ground |
Always |
10 kΩ or higher |
P4-2 (E) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK ECM
(a) Connect the A19 ECM connector.
(b) Connect the 4F and 4H instrument panel junction block assembly connectors.
(c) Measure the voltage according to the value(s) in the table below.
*a |
Component with harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4F-20 - Body ground |
Power switch on (IG) and fuel lid opener switch not pressed |
11 to 14 V |
Power switch on (IG) and fuel lid opener switch pressed |
Below 1 V |
|
4H-28 - Body ground |
Power switch on (IG) and fuel lid opener switch not pressed → fuel lid opener switch pressed |
Below 1 V → 11 to 14 V |
Result | Proceed to |
|---|---|
The result for terminal 4F-20 (with power switch on (IG) and fuel lid opener switch not pressed) is not as specified |
A |
The result for terminal 4H-28 is not as specified |
|
The result for terminal 4F-20 (with power switch on (IG) and fuel lid opener switch pressed) is not as specified |
B |
| A | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
| B | REPLACE ECM |
How To Proceed With Troubleshooting
HINT:
- Use the following procedure to troubleshoot the fuel lid opener system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What
Vehicle model, system name
When
Date, time, occurrence frequency
Where
Road conditions
Under what conditions?
Driving conditions, weather conditions
How did it happen?
Problem symptoms
|
PRE-CHECK
(a) Measure the auxiliary battery voltage with the power switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
|
PROBLEM SYMPTOMS TABLE
(a) Refer to Problem Symptoms Table.
Click here ![]()
Result | Proceed to |
|---|---|
Fault is not listed in Problem Symptoms Table |
A |
Fault is listed in Problem Symptoms Table |
B |
| B | GO TO STEP 6 |
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Data List / Active Test
Click here ![]()
(b) Operation Check
Click here ![]()
(c) Inspection
|
REPAIR OR REPLACE
|
CONFIRMATION TEST
| NEXT | END |
Parts Location
PARTS LOCATION
ILLUSTRATION
*1 |
FUEL LID LOCK WITH MOTOR ASSEMBLY |
*2 |
FUEL LID OPENER SWITCH |
*3 |
COMBINATION METER ASSEMBLY |
*4 |
ECM |
*5 |
NO. 1 ENGINE ROOM RELAY BLOCK AND NO. 1 JUNCTION BLOCK ASSEMBLY - EFI-MAIN NO. 1 RELAY - EFI NO. 1 FUSE - FUEL OPN FUSE - EFI-MAIN NO. 1 FUSE |
*6 |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FUEL OPN RELAY |
*7 |
DLC3 |
- |
- |
Precaution
PRECAUTION
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.
System Name | See Procedure |
|---|---|
Lane Departure Alert System (w/ Steering Control) |
|
Intelligent Clearance Sonar System |
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Pre-collision System |
|
Lighting System (for HV Model with Cornering Light) |
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
Symptom | Suspected Area | Link |
|---|---|---|
Fuel lid opener does not operate |
Proceed to "Fuel Lid Opener does not Operate" |
|
Messages are not displayed on the multi-information display in the combination meter assembly |
Fuel lid lock with motor assembly (fuel lid courtesy switch) |
|
Wire harness or connector |
- |
|
SFI system |
||
Combination meter assembly |
||
ECM |
System Diagram
SYSTEM DIAGRAM



