Hood Support
Components
COMPONENTS
ILLUSTRATION
*1 |
FRONT FENDER UPPER PROTECTOR |
*2 |
HOOD STAY BRACKET |
*3 |
HOOD SUPPORT ASSEMBLY |
*4 |
HOOD SUPPORT BRACKET |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Disposal
DISPOSAL
PROCEDURE
1. DISPOSE OF HOOD SUPPORT ASSEMBLY
(a) Secure the hood support assembly horizontally in a vise with the piston rod pulled out.
(b) Wearing safety glasses, gradually cut a part within the area (a) shown in the illustration using a metal saw to release the gas. Specification:
CAUTION: Although the gas inside the hood support assembly is colorless, odorless and harmless, metal debris may scatter. Therefore, cover hood support assembly with a piece of cloth or other material. |
![]() |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL HOOD SUPPORT BRACKET
(a) Engage the guide.
(b) Install the hood support bracket with the bolt.
Torque:
17,5 N·m {178 kgf·cm, 13 ft·lbf}
2. INSTALL FRONT FENDER UPPER PROTECTOR
(a) Engage the 4 clips to install the front fender upper protector.
3. INSTALL HOOD STAY BRACKET
(a) Engage the guide.
(b) Install the hood stay bracket with the bolt.
Torque:
17,5 N·m {178 kgf·cm, 13 ft·lbf}
4. INSTALL HOOD SUPPORT ASSEMBLY
NOTICE:
- Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.
- Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
- Do not apply any horizontal load to the hood support assembly in order to prevent the piston rod from deforming.
(a) Engage the 2 ball joints to install the hood support assembly. NOTICE: Install the hood support assembly while supporting the hood by hand. |
![]() |
(b) Check that the ball joints are engaged securely and the hood support assembly cannot be pulled off.
Removal
REMOVAL
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE HOOD SUPPORT ASSEMBLY
NOTICE:
- Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.
- Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.
- Do not apply any horizontal load to the hood support assembly in order to prevent the piston rod from deforming.
(a) Using a screwdriver with its tip wrapped with protective tape, slightly raise the 2 stop rings as shown in the illustration.
*a |
Protective Tape |
![]() |
Remove in this Direction (1) |
![]() |
Remove in this Direction (2) |
NOTICE:
- Do not remove the stop rings from the hood support assembly. Raise the stop rings just enough to allow the ball joints to be disengaged.
- Do not reuse the hood support assembly if a stop ring has been removed.
(b) Disengage the 2 ball joints to remove the hood support assembly.
NOTICE:
Remove the hood support assembly while supporting the hood sub-assembly by hand.
2. REMOVE HOOD STAY BRACKET
(a) Remove the bolt. |
![]() |
(b) Disengage the guide to remove the hood stay bracket.
3. REMOVE FRONT FENDER UPPER PROTECTOR
(a) Disengage the 4 clips to remove the front fender upper protector. |
![]() |
4. REMOVE HOOD SUPPORT BRACKET
(a) Remove the bolt. |
![]() |
(b) Disengage the guide to remove the hood support bracket.







