Windshield Outside Moulding
Components
COMPONENTS
ILLUSTRATION
*1 |
FRONT FENDER TO COWL SIDE SEAL |
*2 |
LOWER WINDSHIELD OUTSIDE MOULDING |
*3 |
NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP |
*4 |
NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP |
*5 |
WINDSHIELD GLASS SUB-ASSEMBLY |
- |
- |
● |
Non-reusable part |
- |
- |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP
HINT:
Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.
(a) Using a riveter with a nose piece, install 6 new No. 3 windshield outside moulding clips.
HINT:
If the mandrel of the No. 3 windshield outside moulding clip does not come off on the first operation of the riveter, slide the riveter forward on the mandrel and operate it again.
NOTICE:
- Do not pry the No. 3 windshield outside moulding clip with the riveter, as this will cause damage to the riveter and mandrel.
- Confirm that the No. 3 windshield outside moulding clips are seated properly against the vehicle body.
*a
Riveter
*b
Incorrect
*c
Correct
- Do not tilt the riveter when installing the No. 3 windshield outside moulding clip to the vehicle body.
*a |
Riveter |
*b |
Mandrel |
*c |
Incorrect |
(b) Install the windshield glass sub-assembly.
Click here ![]()
2. INSTALL NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP
HINT:
Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.
(a) Engage the 6 claws to install the 6 No. 1 windshield outside moulding clips as shown in the illustration.
![]() |
Install in this Direction |
- |
- |
3. INSTALL LOWER WINDSHIELD OUTSIDE MOULDING
(a) Engage the 12 claws to install the lower windshield outside moulding. |
![]() |
4. INSTALL FRONT FENDER TO COWL SIDE SEAL
Click here ![]()
Removal
REMOVAL
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE FRONT FENDER TO COWL SIDE SEAL
Click here ![]()
2. REMOVE LOWER WINDSHIELD OUTSIDE MOULDING
(a) Apply protective tape around the lower windshield outside moulding as shown in the illustration.
![]() |
Protective Tape |
(b) Using a screwdriver with its tip wrapped with protective tape, disengage the 12 claws as shown in the illustration.
*a |
Protective Tape |
![]() |
Remove in this Direction |
3. REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP
HINT:
Perform the following procedure only when replacement of a No. 1 windshield outside moulding clip is necessary.
(a) Disengage the 6 claws to remove the 6 No. 1 windshield outside moulding clips as shown in the illustration.
![]() |
Remove in this Direction |
4. REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP
HINT:
Perform the following procedure only when replacement of a No. 3 windshield outside moulding clip is necessary.
(a) Remove the windshield glass sub-assembly.
Click here ![]()
(b) Insert a 4.0 mm (0.157 in.) drill bit into a drill.
(c) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration. Standard Measurement:
NOTICE: Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep. |
|
(d) Lightly press the drill bit against the No. 3 windshield outside moulding clips to drill off the No. 3 windshield outside moulding clip flanges, and remove the 6 No. 3 windshield outside moulding clips. CAUTION: Be careful of the drilled No. 3 windshield outside moulding clips, as they may be hot. NOTICE:
|
|
(e) Using a vacuum cleaner, remove the No. 3 windshield outside moulding clip fragments and shavings from the drilled areas.





