Headlight Dimmer Switch
Components
COMPONENTS
ILLUSTRATION
*A |
for Manual Tilt and Manual Telescopic Steering Column |
*B |
for Power Tilt and Power Telescopic Steering Column |
*1 |
LOWER STEERING COLUMN COVER |
*2 |
TURN SIGNAL SWITCH |
*3 |
UPPER STEERING COLUMN COVER |
- |
- |
Inspection
INSPECTION
PROCEDURE
1. INSPECT TURN SIGNAL SWITCH
*a |
Component without harness connected (Turn Signal Switch) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Light Control SwitchTester Connection | Condition | Specified Condition |
|---|---|---|
2 (L_OFF) - 12 (EL)*1 |
Light control switch in DRL OFF position |
Below 1 Ω |
10 (A) - 12 (EL) |
Light control switch in AUTO position |
Below 1 Ω |
14 (T) - 12 (EL) |
Light control switch in tail position |
Below 1 Ω |
5 (H) - 12 (EL) |
Light control switch in head position |
Below 1 Ω |
Tester Connection | Condition | Specified Condition |
|---|---|---|
6 (HF) - 12 (EL) |
Dimmer switch in high flash position |
Below 1 Ω |
1 (HU) - 12 (EL) |
Dimmer switch in high position |
Below 1 Ω |
Tester Connection | Condition | Specified Condition |
|---|---|---|
9 (TR) - 12 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher |
3 (TL) - 12 (EL) |
Turn signal switch in neutral position |
10 kΩ or higher |
9 (TR) - 12 (EL) |
Turn signal switch in right turn position |
Below 1 Ω |
9 (TR) - 12 (EL) |
Turn signal switch in full right turn position |
Below 1 Ω |
9 (TR) - 11 (CR) |
Turn signal switch in full right turn position |
Below 1 Ω |
11 (CR) - 12 (EL) |
Turn signal switch in full right turn position |
Below 1 Ω |
3 (TL) - 12 (EL) |
Turn signal switch in left turn position |
Below 1 Ω |
3 (TL) - 12 (EL) |
Turn signal switch in full left turn position |
Below 1 Ω |
3 (TL) - 11 (CR) |
Turn signal switch in full left turn position |
Below 1 Ω |
11 (CR) - 12 (EL) |
Turn signal switch in full left turn position |
Below 1 Ω |
- *1: w/ Light Control Switch DRL OFF Position
HINT:
- The left turn or right turn condition indicates a condition in which the turn signal switch will return to the neutral position after releasing your hand from the turn signal switch (turn signal switch is operated approximately 7°).
- The full left turn or full right turn condition indicates a condition in which the turn signal switch will not return to the neutral position after releasing your hand from the turn signal switch (turn signal switch is operated 12°).
If the result is not as specified, replace the turn signal switch.
Installation
INSTALLATION
PROCEDURE
1. INSTALL TURN SIGNAL SWITCH
(a) Engage the claw as shown in the illustration.
![]() |
Install in this Direction |
(b) Install the turn signal switch with the 2 screws.
2. INSTALL UPPER STEERING COLUMN COVER
Click here ![]()
3. INSTALL LOWER STEERING COLUMN COVER
Click here ![]()
4. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)
Click here ![]()
Removal
REMOVAL
PROCEDURE
1. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)
Click here ![]()
2. REMOVE LOWER STEERING COLUMN COVER
Click here ![]()
3. REMOVE UPPER STEERING COLUMN COVER
Click here ![]()
4. REMOVE TURN SIGNAL SWITCH
(a) Remove the 2 screws. |
![]() |
(b) Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the turn signal switch as shown in the illustration.
*a |
Protective Tape |
![]() |
Remove in this Direction |


