Power Window Regulator Motor(for Front Door)
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
for Driver Side |
*B |
for Front Passenger Side |
*1 |
COURTESY LIGHT ASSEMBLY |
*2 |
FRONT DOOR ARMREST COVER SUB-ASSEMBLY |
*3 |
FRONT DOOR TRIM BOARD SUB-ASSEMBLY |
*4 |
FRONT DOOR TRIM POCKET COVER |
*5 |
MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL |
*6 |
POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL |
ILLUSTRATION
*1 |
FRONT DOOR GLASS SUB-ASSEMBLY |
*2 |
FRONT DOOR INNER GLASS WEATHERSTRIP |
*3 |
FRONT DOOR SERVICE HOLE COVER |
*4 |
FRONT DOOR TRIM BRACKET |
*5 |
FRONT DOOR VENT SEAL |
*6 |
FRONT DOOR WINDOW REGULATOR ASSEMBLY |
*7 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY |
*8 |
FRONT DOOR WEATHERSTRIP CLIP |
*9 |
FRONT DOOR NO. 2 SERVICE HOLE COVER |
*10 |
HOLE PLUG |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
![]() |
MP grease |
Inspection
INSPECTION
PROCEDURE
1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR DRIVER DOOR)
(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2. NOTICE: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor. |
|
(b) Connect a negative (-) lead from the auxiliary battery to connector terminals 1 and 7 or 10.
(c) Check that the motor gear rotates smoothly as follows:
OK:
Measurement Condition | Specified Condition |
|---|---|
|
Motor gear rotates clockwise |
|
Motor gear rotates counterclockwise |
- If the result is not as specified, replace the power window regulator motor assembly (for driver door).
CAUTION:
Initialize the power window control system after installing the power window regulator motor and regulator assembly.
2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)
(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2. NOTICE: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor. |
|
(b) Connect a negative (-) lead from the auxiliary battery to connector terminal 1 and 7 or 10.
(c) Check that the motor gear rotates smoothly as follows:
OK:
Measurement Condition | Specified Condition |
|---|---|
|
Motor gear rotates counterclockwise |
|
Motor gear rotates clockwise |
- If the result is not as specified, replace the power window regulator motor assembly (for front passenger door).
CAUTION:
Initialize the power window control system after installing the power window regulator motor and regulator assembly.
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.
(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
Torque:
5,4 N·m {55 kgf·cm, 48 in·lbf}
HINT:
When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
3. INSTALL FRONT DOOR WINDOW REGULATOR ASSEMBLY
Click here ![]()
4. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Click here ![]()
5. INSTALL FRONT DOOR VENT SEAL
Click here ![]()
6. INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
7. INSTALL FRONT DOOR SERVICE HOLE COVER
Click here ![]()
8. INSTALL FRONT DOOR TRIM BRACKET
Click here ![]()
9. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
10. INSTALL COURTESY LIGHT ASSEMBLY
Click here ![]()
11. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here ![]()
12. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here ![]()
13. INSTALL FRONT DOOR TRIM POCKET COVER
Click here ![]()
14. INSTALL FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
15. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
16. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
17. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
18. INSPECT POWER WINDOW OPERATION
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
|
Initialize power window control system |
|
|
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
5. REMOVE FRONT DOOR TRIM POCKET COVER
Click here ![]()
6. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here ![]()
7. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here ![]()
8. REMOVE COURTESY LIGHT ASSEMBLY
Click here ![]()
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
10. REMOVE FRONT DOOR TRIM BRACKET
Click here ![]()
11. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here ![]()
12. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
13. REMOVE FRONT DOOR VENT SEAL
Click here ![]()
14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here ![]()
15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY
Click here ![]()
16. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly. |
![]() |





