Rear Door Belt Moulding
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*1 |
REAR DOOR ARMREST COVER SUB-ASSEMBLY |
*2 |
REAR DOOR TRIM ASSEMBLY COVER |
*3 |
REAR DOOR TRIM BOARD SUB-ASSEMBLY |
*4 |
REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL |
ILLUSTRATION
*1 |
REAR DOOR BELT MOULDING ASSEMBLY |
*2 |
REAR DOOR GLASS RUN |
*3 |
REAR DOOR GLASS SUB-ASSEMBLY |
*4 |
REAR DOOR INNER GLASS WEATHERSTRIP |
*5 |
REAR DOOR NO. 1 TRIM BRACKET |
*6 |
REAR DOOR NO. 2 SERVICE HOLE COVER |
*7 |
REAR DOOR REAR GUIDE SEAL |
*8 |
REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY |
*9 |
REAR DOOR SERVICE HOLE COVER |
*10 |
REAR DOOR WEATHERSTRIP |
*11 |
HOLE PLUG |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. INSTALL REAR DOOR BELT MOULDING ASSEMBLY
(a) Engage the 7 claws to install a new rear door belt moulding assembly as shown in the illustration.
![]() |
Install in this Direction |
3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
4. INSTALL REAR DOOR REAR GUIDE SEAL
Click here ![]()
5. CONNECT REAR DOOR WEATHERSTRIP
Click here ![]()
6. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
7. INSTALL REAR DOOR GLASS RUN
Click here ![]()
8. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
10. INSTALL REAR DOOR SERVICE HOLE COVER
Click here ![]()
11. INSTALL REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
12. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
14. INSTALL REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
15. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
16. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
17. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
18. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
19. INSPECT POWER WINDOW OPERATION
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door belt moulding assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
|
Initialize power window control system |
|
|
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
5. REMOVE REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
8. REMOVE REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
9. REMOVE REAR DOOR SERVICE HOLE COVER
Click here ![]()
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
12. REMOVE REAR DOOR GLASS RUN
Click here ![]()
13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
14. DISCONNECT REAR DOOR WEATHERSTRIP
Click here ![]()
15. REMOVE REAR DOOR REAR GUIDE SEAL
Click here ![]()
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
17. REMOVE REAR DOOR BELT MOULDING ASSEMBLY
(a) Apply protective tape around the rear door belt moulding assembly as shown in the illustration.
![]() |
Protective Tape |
(b) Disengage the 7 claws to remove the rear door belt moulding assembly as shown in the illustration.
![]() |
Remove in this Direction |




