Power Window Regulator Motor(for Rear Door)
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*1 |
REAR DOOR ARMREST COVER SUB-ASSEMBLY |
*2 |
REAR DOOR TRIM ASSEMBLY COVER |
*3 |
REAR DOOR TRIM BOARD SUB-ASSEMBLY |
*4 |
REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL |
ILLUSTRATION
*1 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY |
*2 |
REAR DOOR GLASS RUN |
*3 |
REAR DOOR GLASS SUB-ASSEMBLY |
*4 |
REAR DOOR INNER GLASS WEATHERSTRIP |
*5 |
REAR DOOR NO. 1 TRIM BRACKET |
*6 |
REAR DOOR NO. 2 SERVICE HOLE COVER |
*7 |
REAR DOOR REAR GUIDE SEAL |
*8 |
REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY |
*9 |
REAR DOOR SERVICE HOLE COVER |
*10 |
REAR DOOR WEATHERSTRIP |
*11 |
REAR DOOR WINDOW REGULATOR ASSEMBLY |
*12 |
HOLE PLUG |
*13 |
REAR DOOR NO. 3 SERVICE HOLE COVER |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
![]() |
MP grease |
Inspection
INSPECTION
PROCEDURE
1. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR LH DOOR)
(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2. NOTICE: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor. |
|
(b) Connect a negative (-) lead from the auxiliary battery to connector terminal 1 and 7 or 10.
(c) Check that the motor gear rotates smoothly as follows:
OK:
Measurement Condition | Specified Condition |
|---|---|
|
Motor gear rotates clockwise |
|
Motor gear rotates counterclockwise |
- If the result is not as specified, replace the power window regulator motor assembly (for rear LH door).
CAUTION:
Initialize the power window control system after installing the power window regulator motor and regulator assembly.
2. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (FOR REAR RH DOOR)
(a) Connect a positive (+) lead from the auxiliary battery to connector terminal 2. NOTICE: Do not connect a positive (+) lead from the auxiliary battery to any terminal other than terminal 2 to avoid damaging the pulse sensor inside the motor. |
|
(b) Connect a negative (-) lead from the auxiliary battery to connector terminals 1 and 7 or 10.
(c) Check that the motor gear rotates smoothly as follows:
OK:
Measurement Condition | Specified Condition |
|---|---|
|
Motor gear rotates counterclockwise |
|
Motor gear rotates clockwise |
- If the result is not as specified, replace the power window regulator motor assembly (for rear RH door).
CAUTION:
Initialize the power window control system after installing the power window regulator motor and regulator assembly.
Installation
INSTALLATION
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
NOTICE:
The regulator arm must be below the intermediate position when installing the power window regulator motor assembly.
(a) Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
Torque:
5,4 N·m {55 kgf·cm, 48 in·lbf}
HINT:
When replacing a power window regulator motor assembly, a new power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY
Click here ![]()
4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
5. INSTALL REAR DOOR REAR GUIDE SEAL
Click here ![]()
6. CONNECT REAR DOOR WEATHERSTRIP
(a) Engage the clip and connect the rear door weatherstrip.
7. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
8. INSTALL REAR DOOR GLASS RUN
Click here ![]()
9. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
11. INSTALL REAR DOOR SERVICE HOLE COVER
Click here ![]()
12. INSTALL REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
13. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
14. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
15. INSTALL REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
16. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
17. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
18. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
19. INITIALIZE POWER WINDOW CONTROL SYSTEM
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
20. INSPECT POWER WINDOW OPERATION
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
|
Initialize power window control system |
|
|
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
4. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY
Click here ![]()
5. REMOVE REAR DOOR TRIM ASSEMBLY COVER
Click here ![]()
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here ![]()
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here ![]()
8. REMOVE REAR DOOR NO. 1 TRIM BRACKET
Click here ![]()
9. REMOVE REAR DOOR SERVICE HOLE COVER
Click here ![]()
10. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP
Click here ![]()
11. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER
Click here ![]()
12. REMOVE REAR DOOR GLASS RUN
Click here ![]()
13. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY
Click here ![]()
14. DISCONNECT REAR DOOR WEATHERSTRIP
(a) Disengage the clip and disconnect the rear door weatherstrip until the screws of the rear door rear guide seal is visible.
15. REMOVE REAR DOOR REAR GUIDE SEAL
Click here ![]()
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here ![]()
17. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
Click here ![]()
18. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly. |
![]() |





