ECU Terminals
ECU TERMINALS
ECU TERMINALS
*a |
Component without wire harness connected Skid control ECU (brake actuator assembly) |
- |
- |
Terminal No. (Symbol) | Terminal Description |
|---|---|
1 (+BM) |
ABS motor relay power supply |
2 |
- |
3 |
- |
4 |
- (not used) |
5 (CANH) |
CAN H communication line |
6 (CSW) |
VSC OFF switch input |
7 (FL-) |
Front left wheel speed signal input (-) |
8 |
- (not used) |
9 |
- (not used) |
10 (STPO) |
Stop light relay control output |
11 |
- (not used) |
12 |
- |
13 |
- |
14 (GND2) |
Pump motor ground |
15 |
- |
16 |
- |
17 (FSW+) |
Brake pedal force sensor switch input |
18 |
- (not used) |
19 (CANL) |
CAN L communication line |
20 |
- (not used) |
21 (FR+) |
Front right wheel speed signal input (+) |
22 (RR+) |
Rear right wheel speed signal input (+) |
23 (RL-) |
Rear left wheel speed signal input (-) |
24 (FL+) |
Front left wheel speed signal input (+) |
25 |
- (not used) |
26 (FR-) |
Front right wheel speed signal input (-) |
27 |
- (not used) |
28 |
- (not used) |
29 |
- (not used) |
30 (+BS) |
ABS solenoid valve relay power supply |
31 |
- |
32 |
- |
33 |
- |
34 (SP1) |
Speed signal output to speedometer |
35 |
- |
36 (IG1) |
IG1 power supply input |
37 (RR-) |
Rear right wheel speed signal input (-) |
38 |
- (not used) |
39 (RL+) |
Rear left wheel speed signal input (+) |
40 |
- (not used) |
41 |
- (not used) |
42 (STP) |
Stop light relay control input |
43 (HZRI) |
Brake hold switch input |
44 (STP2) |
Stop light switch input |
45 |
- |
46 (GND1) |
Skid control ECU ground |
TERMINAL INSPECTION
(a) Disconnect the connector and measure the voltage and resistance at the wire harness side.
HINT:
Voltage cannot be measured while the connector is connected to the skid control ECU (brake actuator assembly), because the connector is waterproof.
StandardTerminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A42-1 (+BM) - Body ground |
L - Body ground |
ABS motor relay power supply |
Always |
11 à 14 V |
A42-6 (CSW) - Body ground |
R - Body ground |
VSC OFF switch input |
VSC OFF switch ON → OFF (pressed → released) |
Below 1 Ω → 10 kΩ or higher |
A42-10 (STPO) - Body ground |
R - Body ground |
Stop light relay control output (stop light switch assembly) |
Ignition Switch in ON position |
11 à 14 V |
A42-14 (GND2) - Body ground |
W-B - Body ground |
Pump motor ground |
Always |
Below 1 Ω |
A42-17 (FSW+) - Body ground |
GR - Body ground |
Brake pedal force sensor switch input |
Brake pedal force sensor switch OFF → ON (brake pedal depressed → released) |
950 à 1 050 Ω → 203 à 223 Ω |
A42-30 (+BS) - Body ground |
W - Body Ground |
ABS solenoid valve relay power supply |
Always |
11 à 14 V |
A42-36 (IG1) - Body ground |
B - Body ground |
IG1 power supply input |
Ignition Switch in ON position |
11 à 14 V |
A42-42 (STP) - Body ground |
SB - Body ground |
Stop light relay control output (stop light switch assembly) |
Stop light switch ON → OFF (brake pedal depressed → released) |
11 to 14 V* → Below 1.5 V |
A42-43 (HZRI) - Body ground |
B - Body ground |
Brake hold switch input |
Brake hold switch ON → OFF (released → depressed) |
Below 1 Ω → 10 kΩ or higher |
A42-44 (STP2) - Body ground |
L - Body ground |
Stop light switch input |
Stop light switch assembly ON → OFF (brake pedal depressed → released) |
11 to 14 V* → Below 1.5 V |
A42-46 (GND1) - Body ground |
W-B - Body ground |
Skid control ECU ground |
Always |
Below 1 Ω |
HINT:
*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.
*a |
Front view of wire harness connector (to skid control ECU (brake actuator assembly)) |