Brake Control / Dynamic Control Systems

ABS warning light stays on

~4min read

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication. The ABS warning light stays on when any of the following conditions is detected:

  • The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
  • There is a malfunction in the internal circuit of the skid control ECU (brake actuator assembly).
  • There is an open in the wire harness between the combination meter and the skid control ECU (brake actuator assembly).
  • The ABS is malfunctioning.

HINT:

In some cases, the Techstream cannot be used if the skid control ECU (brake actuator assembly) is abnormal.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

Result:

Result

Proceed to

No DTCs are output.

A

DTCs are output.

B

B

INSPECT CAN COMMUNICATION SYSTEM

A
  1. CHECK THAT BRAKE ACTUATOR ASSEMBLY CONNECTOR IS PROPERLY CONNECTED

(a) Check that the skid control ECU (brake actuator assembly) connector is properly connected.

OK:

The connector is correctly connected.

NG

CONNECT CONNECTOR TO ECU PROPERLY

OK
  1. CHECK BATTERY

(a) Check the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (IG1))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-30 (+BS) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (IG1))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-36 (IG1) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE TERMINAL)

OK
  1. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-46 (GND1) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

OK
  1. READ VALUE USING TECHSTREAM (ABS WARNING LIGHT)

(a) Reconnect connector A42 to the skid control ECU (brake actuator assembly).

(b) Select the Data List on the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ABS Warning Light

ABS Warning Light

ON or OFF

ON: Indicator on

OFF: Indicator off

-

Chassis > ABS/VSC/TRAC/EPB > Data List

ABS Warning Light

(c) Check the Techstream display condition of the ABS warning light.

Result:

Result

Proceed to

The message "ON" is displayed.

A

OFF is displayed.

B

A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

CHECK METER / GAUGE SYSTEM