Brake Control / Dynamic Control Systems

Speed Sensor Rotor Malfunction (C1237)

~28min read

DESCRIPTION

The skid control ECU (brake actuator assembly) calculates the rotation speed of each wheel based on the signals sent from each wheel speed sensor.

These signals are used to determine whether all four wheels are operating correctly.

Therefore, the signals from all wheels must be identical.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1237

Speed sensor rotor malfunction

One of the following conditions is detected:

  • Difference in output voltage between the four wheel speed sensors.
  • Abnormal pulse signals from 3 or more sensors.
  • Continuous ABS control is performed for 60 seconds or more.
  • VSC control is performed for 10 seconds or more.
  • Tire and wheel size
  • Tire deformation
  • Speed Sensor Rotor
  • Speed sensor
  • Speed Sensor Circuit
  • Skid control ECU (brake actuator assembly)
DTC detection conditions:

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Diagnostic Condition

-

-

-

-

-

Malfunction Status

Difference in output voltage between the four wheel speed sensors.

○

-

-

-

Abnormal pulse signals.

-

○

-

-

Continuous ABS control is performed.

-

-

○

-

VSC control is performed.

-

-

-

○

Detection Duration

-

3 seconds minimum

60 seconds or more

10 seconds minimum

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467.

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

Click here

PROCEDURE

  1. CONFIRM DTC AGAIN

(a) Clear the DTCs.

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(b) Turn the ignition switch OFF.

(c) Start the engine.

(d) Drive the vehicle at a speed of 54 km/h or more for at least 120 seconds.

(e) Check whether the same DTC is output.

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1237 is set

A

C1237 and C1330, C1331, C1332, C1333, C1464, C1465, C1466, C1467 are output simultaneously

B

B

GO TO DTC (C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467)

A
  1. CHECK TIRES

(a) Check the size and condition of all four tires.

Click here

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.

OK:

The diameter and air pressure of each of the four tires are the same.

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE

OK
  1. CHECK VALUE USING TECHSTREAM (SIGNAL SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Select the Data List using the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FR Wheel Speed

Front right wheel speed sensor value

Min.: 0 km/h, Max.: 326 km/h

Vehicle stopped: 0 km/h

When vehicle is driving at constant speed: No large fluctuation

FL Wheel Speed

Front left wheel speed sensor value

Min.: 0 km/h, Max.: 326 km/h

Vehicle stopped: 0 km/h

When vehicle is driving at constant speed: No large fluctuation

RR Wheel Speed

Rear right wheel speed sensor value

Min.: 0 km/h, Max.: 326 km/h

Vehicle stopped: 0 km/h

When vehicle is driving at constant speed: No large fluctuation

RL Wheel Speed

Rear left wheel speed sensor value

Min.: 0 km/h, Max.: 326 km/h

Vehicle stopped: 0 km/h

When vehicle is driving at constant speed: No large fluctuation

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

FR Wheel Speed

FL Wheel Speed

RR Wheel Speed

RL Wheel Speed

(d) Check the output value of the speed sensor.

OK:

The output value changes according to the vehicle speed.

Result:

Result

Proceed to

OK

A

NG (the output value for the front RH speed sensor does not change according to the vehicle speed)

B

NG (the output value for the front LH speed sensor does not change according to the vehicle speed)

C

NG (the output value for the rear RH speed sensor does not change according to the vehicle speed)

D

NG (the output value for the rear LH speed sensor does not change according to the vehicle speed)

E

NG (the output value of at least 2 sensors does not change according to the vehicle speed)

F

B

GO TO STEP 5

C

GO TO STEP 12

D

GO TO STEP 19

E

GO TO STEP 26

F

REPLACE BRAKE ACTUATOR ASSEMBLY

A
  1. PERFORM CHECK IN TEST MODE (SIGNAL CHECK)

(a) Turn the ignition switch OFF.

(b) Perform the sensor check using the test mode procedure.

Click here

Chassis > ABS/VSC/TRAC/EPB > Utility

Signal Check

OK:

All DTCs in test mode are cleared.

Result:

Result

Proceed to

OK

A

NG (the output value for the front RH speed sensor does not change according to the vehicle speed)

B

NG (the output value for the front LH speed sensor does not change according to the vehicle speed)

C

NG (the output value for the rear RH speed sensor does not change according to the vehicle speed)

D

NG (the output value for the rear LH speed sensor does not change according to the vehicle speed)

E

NG (the output value of at least 2 sensors does not change according to the vehicle speed)

F

A

USE SIMULATION METHOD TO CHECK

B

GO TO STEP 5

C

GO TO STEP 12

D

GO TO STEP 19

E

GO TO STEP 26

  1. CHECK FRONT RH SPEED SENSOR INSTALLATION

(a) Turn the ignition switch OFF.

*1

Front right speed sensor

*a

Correct

*b

Incorrect

*c

8,5 N*m

*d

No looseness

(b) Check the speed sensor installation.

OK:

There is no looseness between the sensor and the front RH steering knuckle.

The installation bolt is correctly tightened.

Torque

8.5 N*m (87 kgf*cm, 75 lbf*in)

NG

REINSTALL OR REPLACE FRONT RH SPEED SENSOR

OK
  1. CHECK FRONT RH SPEED SENSOR (CHECK FOR FOREIGN MATTER)

(a) Remove the front RH speed sensor.

Click here

(b) Check the speed sensor tip.

OK:

The sensor tip has no scratches, oil or foreign matter.

NOTICE:

  • If there is oil or foreign matter on the speed sensor, clean the speed sensor.
  • If the speed sensor is damaged, replace it with a new one.
  • Check the speed sensor signal after cleaning or replacement:

    Click here

NG

CLEAN OR REPLACE FRONT RH SPEED SENSOR

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

(a) Check that there is no looseness at the connector lock and connections.

OK:

The connector is correctly connected.

*a

Front view of wire harness side connector

(to front RH speed sensor)

(b) Disconnect the front RH speed sensor connector.

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to the ON position.

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A25-1 (FR+) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

GO TO STEP 10

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A25-1 (FR+) - A25-2 (FR-)

Ignition Switch in ON position

11 à 14 V

*a

Front view of wire harness side connector

(to front RH speed sensor)

NG

GO TO STEP 11

OK
  1. CHECK FRONT SPEED SENSOR ROTOR (FRONT RH AXLE HUB ASSEMBLY) (CHECK FOR FOREIGN MATTER)

(a) Remove the front speed sensor rotor (front RH axle hub assembly).

Click here

(b) Check the speed sensor rotor.

OK:

The rotor has no scratches, oil or foreign matter.

NOTICE:

  • If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.
  • If the speed sensor rotor is damaged, replace it with a new one.
  • Check the speed sensor signal after cleaning or replacement:

    Click here

HINT:

  • The front speed sensor rotor is integral with the front axle hub assembly.
  • If the front speed sensor rotor must be replaced, replace it together with the front axle hub assembly.

Result:

Result

Proceed to

OK

A

NG (the speed sensor rotor is damaged.)

B

NG (foreign matter is present on the speed sensor rotor.)

C

A

REPLACE FRONT RH SPEED SENSOR

B

REPLACE FRONT RH AXLE HUB SUB-ASSEMBLY

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT RH AXLE HUB ASSEMBLY)

  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT RH SPEED SENSOR)

(a) Turn the ignition switch OFF.

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-26 (FR-) - A25-2 (FR-)

Always

Below 1 Ω

A42-26 (FR-) or A25-2 (FR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT RH SPEED SENSOR)

(a) Turn the ignition switch OFF.

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-26 (FR-) - A25-2 (FR-)

Always

Below 1 Ω

A42-26 (FR-) or A25-2 (FR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK FRONT LH SPEED SENSOR INSTALLATION

(a) Turn the ignition switch OFF.

*1

Front left speed sensor

*a

Correct

*b

Incorrect

*c

8,5 N*m

*d

No looseness

(b) Check the speed sensor installation.

OK:

There is no looseness between the sensor and the front LH steering knuckle.

The installation bolt is correctly tightened.

Torque

8.5 N*m (87 kgf*cm, 75 lbf*in)

NG

REINSTALL OR REPLACE FRONT LH SPEED SENSOR

OK
  1. CHECK FRONT LH SPEED SENSOR (CHECK FOR FOREIGN MATTER)

(a) Remove the front LH speed sensor.

Click here

(b) Check the speed sensor tip.

OK:

The sensor tip has no scratches, oil or foreign matter.

NOTICE:

  • If there is oil or foreign matter on the speed sensor, clean the speed sensor.
  • If the speed sensor is damaged, replace it with a new one.
  • Check the speed sensor signal after cleaning or replacement:

    Click here

NG

CLEAN OR REPLACE FRONT LH SPEED SENSOR

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

(a) Check that there is no looseness at the connector lock and connections.

OK:

The connector is correctly connected.

*a

Front view of wire harness side connector

(to front LH speed sensor)

(b) Disconnect the front LH speed sensor connector.

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to the ON position.

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A13-1 (FL+) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

GO TO STEP 17

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A13-1 (FL+) - A13-2 (FL-)

Ignition Switch in ON position

11 à 14 V

*a

Front view of wire harness side connector

(to front LH speed sensor)

NG

GO TO STEP 18

OK
  1. CHECK FRONT SPEED SENSOR ROTOR (FRONT LH AXLE HUB ASSEMBLY) (CHECK FOR FOREIGN MATTER)

(a) Remove the front speed sensor rotor (front LH axle hub assembly).

Click here

(b) Check the speed sensor rotor.

OK:

The rotor has no scratches, oil or foreign matter.

NOTICE:

  • If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.
  • If the speed sensor rotor is damaged, replace it with a new one.
  • Check the speed sensor signal after cleaning or replacement:

    Click here

HINT:

  • The front speed sensor rotor is integral with the front axle hub assembly.
  • If the front speed sensor rotor must be replaced, replace it together with the front axle hub assembly.

Result:

Result

Proceed to

OK

A

NG (the speed sensor rotor is damaged.)

B

NG (foreign matter is present on the speed sensor rotor.)

C

A

REPLACE FRONT LH SPEED SENSOR

B

REPLACE FRONT LH AXLE HUB SUB-ASSEMBLY

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT RH AXLE HUB ASSEMBLY)

  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT LH SPEED SENSOR)

(a) Turn the ignition switch OFF.

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-7 (FL-) - A13-2 (FL-)

Always

Below 1 Ω

A42-7 (FL-) or A13-2 (FR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT LH SPEED SENSOR)

(a) Turn the ignition switch OFF.

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-7 (FL-) - A13-2 (FL-)

Always

Below 1 Ω

A42-7 (FL-) or A13-2 (FR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK RR SPEED SENSOR RH INSTALLATION

(a) Turn the ignition switch OFF.

*1

Rear right speed sensor

*a

OK

*b

NG

*c

No looseness

(b) Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.

HINT:

As the rear RH axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs to be replaced, replace the rear RH axle hub and bearing assembly.

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

(a) Check that there is no looseness at the connector lock and connections.

OK:

The connector is correctly connected.

*a

Front view of wire harness side connector

(to RR speed sensor RH)

(b) Disconnect the RR speed sensor RH connector.

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to the ON position.

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

d1-2 (RR+) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

GO TO STEP 22

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

d1-2 (RR+) - d1-1 (RR-)

Ignition Switch in ON position

11 à 14 V

*a

Front view of wire harness side connector

(to RR speed sensor RH)

OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

GO TO STEP 24

  1. CHECK SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY)

(a) Turn the ignition switch OFF.

*1

Skid Control Sensor Wire RH (No. 1 Parking Brake Cable Assembly)

*a

Front view of wire harness side connector

(to sensor side connector)

*b

Front view of wire harness side connector

(to vehicle side connector)

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Remove the skid control sensor wire RH (No. 1 parking brake cable assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

d1-1 (RR-) - dM1-2 (RR-)

Always

Below 1 Ω

d1-1 (RR-) - dM1-1 (RR+)

Always

10 kΩ minimum

d1-1 (RR-) or dM1-2 (RR-) - Body ground

Always

10 kΩ minimum

NOTICE:

Check the speed sensor signal after replacement.

Click here

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY))

(a) Make sure there is no looseness in the lock and connector connection.

OK:

The connector is correctly connected.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-37 (RR-) - dM1-2 (RR-)

Always

Below 1 Ω

A42-37 (RR-) or dM1-2 (RR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY)

(a) Turn the ignition switch OFF.

*1

Skid Control Sensor Wire RH (No. 1 Parking Brake Cable Assembly)

*a

Front view of wire harness side connector

(to sensor side connector)

*b

Front view of wire harness side connector

(to vehicle side connector)

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Remove the skid control sensor wire RH (No. 1 parking brake cable assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

d1-1 (RR-) - dM1-2 (RR-)

Always

Below 1 Ω

d1-1 (RR-) - dM1-1 (RR+)

Always

10 kΩ minimum

d1-1 (RR-) or dM1-2 (RR-) - Body ground

Always

10 kΩ minimum

NOTICE:

Check the speed sensor signal after replacement.

Click here

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE CABLE ASSEMBLY))

(a) Make sure there is no looseness in the lock and connector connection.

OK:

The connector is correctly connected.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-37 (RR-) - dM1-2 (RR-)

Always

Below 1 Ω

A42-37 (RR-) or dM1-2 (RR-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK RR SPEED SENSOR LH INSTALLATION

(a) Turn the ignition switch OFF.

*1

Rear left speed sensor

*a

OK

*b

NG

*c

No looseness

(b) Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.

HINT:

As the rear LH axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs to be replaced, replace the rear LH axle hub and bearing assembly.

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

(a) Check that there is no looseness at the connector lock and connections.

OK:

The connector is correctly connected.

*a

Front view of wire harness side connector

(to RR speed sensor LH)

(b) Disconnect the RR speed sensor LH connector.

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to the ON position.

(e) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

e1-2 (RL+) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

GO TO STEP 29

OK
  1. CHECK BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

(a) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

e1-2 (RL+) - e1-1 (RL-)

Ignition Switch in ON position

11 à 14 V

*a

Front view of wire harness side connector

(to RR speed sensor LH)

OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

GO TO STEP 31

  1. CHECK SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY)

(a) Turn the ignition switch OFF.

*1

Skid Control Sensor Wire LH (No. 2 Parking Brake Cable Assembly)

*a

Front view of wire harness side connector

(to sensor side connector)

*b

Front view of wire harness side connector

(to vehicle side connector)

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Remove the skid control sensor wire LH (No. 2 parking brake cable assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

e1-1 (RL-) - eM1-2 (RL-)

Always

Below 1 Ω

e1-1 (RL-) - eM1-1 (RL+)

Always

10 kΩ minimum

e1-1 (RL-) or eM1-2 (RL-) - Body ground

Always

10 kΩ minimum

NOTICE:

Check the speed sensor signal after replacement.

Click here

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY))

(a) Make sure there is no looseness in the lock and connector connection.

OK:

The connector is correctly connected.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-23 (RL-) - eM1-2 (RL-)

Always

Below 1 Ω

A42-23 (RL-) or eM1-2 (RL-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY)

(a) Turn the ignition switch OFF.

*1

Skid Control Sensor Wire LH (No. 2 Parking Brake Cable Assembly)

*a

Front view of wire harness side connector

(to sensor side connector)

*b

Front view of wire harness side connector

(to vehicle side connector)

(b) Check that the connector locks and connections have no looseness.

OK:

The connector is correctly connected.

(c) Remove the skid control sensor wire LH (No. 2 parking brake cable assembly).

(d) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

e1-1 (RL-) - eM1-2 (RL-)

Always

Below 1 Ω

e1-1 (RL-) - eM1-1 (RL+)

Always

10 kΩ minimum

e1-1 (RL-) or eM1-2 (RL-) - Body ground

Always

10 kΩ minimum

NOTICE:

Check the speed sensor signal after replacement.

Click here

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE CABLE ASSEMBLY))

(a) Make sure there is no looseness in the lock and connector connection.

OK:

The connector is correctly connected.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Check the connector housing and terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-23 (RL-) - eM1-2 (RL-)

Always

Below 1 Ω

A42-23 (RL-) or eM1-2 (RL-) - Body ground

Always

10 kΩ minimum

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR