Brake Control / Dynamic Control Systems

Test Mode Procedure

~9min read

TEST MODE PROCEDURE

INITIAL WARNING LIGHT CHECK

(a) When the ignition switch is turned ON, check that the ABS warning light, brake system warning light (red), VSC OFF indicator light, multi-information display (TRAC OFF message) (for color TFT type), TRAC OFF indicator light (for monochrome TFT type), brake hold standby light, brake hold operation light and skid control warning light come on for approximately 3 seconds.

HINT:

  • If the brake fluid level is low, the brake system warning light (red) comes on.
  • If the skid control ECU (brake actuator assembly) stores a DTC, the ABS warning light and skid control warning light come on.
  • If any of the warning lights remain on or do not come on, troubleshoot the warning light circuits indicated below.

Suspected Area

See procedure

ABS Warning Light Circuit (Remains On)

ABS Warning Light Circuit (Does Not Come On)

Brake System Warning Light (Red) Circuit (Remains On)

Brake System Warning Light (Red) Circuit (Does Not Come On)

TRAC OFF Indicator Light Circuit (Remains On)

TRAC OFF Indicator Light Circuit (Does Not Come On)

VSC OFF Indicator Light Circuit (Remains On)

VSC OFF Indicator Light Circuit (Does Not Come On)

Skid Control Warning Light Circuit (Remains On)

Skid Control Warning Light Circuit (Does Not Come On)

Brake Hold Standby Light Circuit

Brake Hold Operation Light Circuit

SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (using TECHSTREAM)

NOTICE:

Perform Test Mode with the vehicle stopped.

HINT:

  • DTCs are stored if malfunctions are detected during each sensor check.
  • When switching to Test Mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly and determines whether the vehicle is equipped with a pre-collision safety system. Therefore, do not exit Test Mode within 5 seconds after switching to Test Mode. (with pre-collision safety system)

(a) Test Mode entry procedure

(1) Turn the ignition switch OFF.

(2) Check that the steering wheel is centered.

(3) Check that the shift lever is in P.

(4) Connect the Techstream to the DLC3.

(5) Turn the ignition switch ON.

(6) Turn on the Techstream.

(7) Switch the skid control ECU (brake actuator assembly) to Test Mode using the Techstream. Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Signal Check.

Chassis > ABS/VSC/TRAC/EPB > Utility

Signal Check

HINT:

Do not exit Test Mode within 5 seconds after switching to Test Mode. If Test Mode is exited within 5 seconds after switching to it, DTC U0235 may be stored. If DTC U0235 is output after exiting Test Mode, switch to Test Mode again, wait at least 5 seconds, then check the DTCs again. (with pre-collision safety system)

(8) Check that the ABS warning light and skid control warning light come on for several seconds, then flash in the Test Mode flashing sequence.

HINT:

If the ABS warning light and skid control warning light do not flash, check the ABS warning light and skid control warning light circuits.

(9) Check the ABS sensors.

HINT:

Check that the ABS warning light flashes according to the Test Mode sequence before performing the following ABS sensor checks.

(b) Check the VSC OFF switch (electric parking brake switch assembly)

(1) Press the VSC OFF switch (electric parking brake switch assembly).

(2) Check that the VSC OFF indicator light comes on.

(3) Press the VSC OFF switch (electric parking brake switch assembly) again.

(c) Brake hold switch (electric parking brake switch assembly)

HINT:

Perform the check with the system in normal condition.

(1) Check that the following conditions are met:

  • The driver's door is closed.
  • The driver's seat belt is fastened.

(2) Press the brake hold switch (electric parking brake switch assembly).

(3) Check that the brake hold standby light comes on.

(4) Press the brake hold switch (electric parking brake switch assembly) again.

(d) Vehicle speed sensor check

(1) Drive the vehicle straight ahead in forward gear.

Accelerate the vehicle to a speed of at least 45 km/h for several seconds.

HINT:

  • The vehicle speed sensor check may not complete if the wheels slip.
  • The speed sensor check may not complete if it is started while the steering wheel is turned.

NOTICE:

Once the ABS warning light is off, a sensor check code is recorded again if the vehicle speed exceeds 80 km/h.

Decelerate or stop the vehicle before it reaches a speed of 80 km/h.

(2) Make sure the ABS warning light turns off.

HINT:

  • The ABS warning light turns off when the sensor check is complete.
  • The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.

(3) Stop the vehicle.

HINT:

When the sensor check is complete, the ABS warning light turns off while the vehicle is driven, and flashes in test mode when the vehicle is stopped.

NOTICE:

If the sensor check has not completed, the ABS warning light flashes even while the vehicle is driven and the ABS system is not operating.

(e) Sensor check completion

(1) When the sensor check is complete, the ABS warning light turns off while the vehicle is driven, and flashes in test mode when the vehicle is stopped.

NOTICE:

  • When the speed sensor and master cylinder pressure sensor checks are complete, the sensor check is finished.
  • If the sensor checks have not completed, the ABS warning light keeps flashing even while the vehicle is driven and the ABS system is not operating.
  • If malfunctions are detected in test mode (signal check), the ABS warning light stays on.
  • If DTCs are output, or if test mode (signal check) items do not complete even after repeated attempts, repair or replace the faulty part.

(f) End of test mode (signal check)

(1) Turn the ignition switch to OFF and disconnect the Techstream.

(g) Test mode (signal check) item table

Item name

Range

Estimation description

Suspected Area

Front right speed sensor output signal

Incomplete/Complete

Make sure there are no foreign objects, and check the gap between the sensor and the rotor

  • Open or short circuit in speed sensor
  • Open or short circuit in sensor system wire harness
  • Faulty connector contact or increased terminal resistance
  • Improper speed sensor installation
  • Sensor rotor system malfunction

Front left speed sensor output signal

Incomplete/Complete

Make sure there are no foreign objects, and check the gap between the sensor and the rotor

  • Open or short circuit in speed sensor
  • Open or short circuit in sensor system wire harness
  • Faulty connector contact or increased terminal resistance
  • Improper speed sensor installation
  • Sensor rotor system malfunction

Rear right speed sensor output signal

Incomplete/Complete

Make sure there are no foreign objects, and check the gap between the sensor and the rotor

  • Open or short circuit in speed sensor
  • Open or short circuit in sensor system wire harness
  • Faulty connector contact or increased terminal resistance
  • Improper speed sensor installation
  • Sensor rotor system malfunction

Rear left speed sensor output signal

Incomplete/Complete

Make sure there are no foreign objects, and check the gap between the sensor and the rotor

  • Open or short circuit in speed sensor
  • Open or short circuit in sensor system wire harness
  • Faulty connector contact or increased terminal resistance
  • Improper speed sensor installation
  • Sensor rotor system malfunction

Front right speed sensor output signal change

Incomplete/Complete

  • Evaluate the stability of the sensor input waveform
  • Evaluate straight-ahead / driving signal inputs
  • A foreign object is present in the speed sensor
  • Sensor rotor system malfunction

Front left speed sensor output signal change

Incomplete/Complete

  • Evaluate the stability of the sensor input waveform
  • Evaluate straight-ahead / driving signal inputs
  • A foreign object is present in the speed sensor
  • Sensor rotor system malfunction

Rear right speed sensor output signal change

Incomplete/Complete

  • Evaluate the stability of the sensor input waveform
  • Evaluate straight-ahead / driving signal inputs
  • A foreign object is present in the speed sensor
  • Sensor rotor system malfunction

Rear left speed sensor output signal change

Incomplete/Complete

  • Evaluate the stability of the sensor input waveform
  • Evaluate straight-ahead / driving signal inputs
  • A foreign object is present in the speed sensor
  • Sensor rotor system malfunction

Malfunction evaluation

Incomplete/Complete

Make sure the brake pedal load detection switch is normal

  • Open or short circuit in brake pedal load detection switch system wire harness
  • Brake pedal load detection switch stuck in ON/OFF position