Brake Control / Dynamic Control Systems

Low Voltage Power Supply Malfunction (C1241)

~6min read

DESCRIPTION

When a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and disables ABS operation through the fail-safe function. This DTC is stored when the +BS terminal voltage deviates from the DTC detection conditions due to a malfunction in the power supply circuit or charging circuit, such as the battery or alternator circuit. This DTC is cleared when the +BS terminal voltage returns to its normal value.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1241

Low voltage power supply malfunction

One of the following conditions is detected:

  • Vehicle speed is at least 6 km/h and the +BS terminal voltage (low voltage) is less than 9.6 V for at least 1 second.
  • Vehicle speed is at least 6 km/h and the +BS terminal voltage (very low voltage) is less than 6.9 V for at least 1 second.
  • Vehicle speed is at least 15 km/h, the +BS terminal voltage is at least 9.6 V, the skid control ECU (brake actuator assembly) turns on more than once within a short period of time, and the power supply voltage drop relay exceeds the threshold.*
  • The +BS terminal voltage is below 6.7 V and the skid control ECU (brake actuator assembly) determines that the power supply voltage is abnormal for at least 0.06 seconds.
  • ABS-MAIN Fuse
  • Battery
  • Charging system
  • Power supply circuit
  • Ground circuit
  • Skid control ECU (brake actuator assembly) internal power supply circuit

*: The skid control ECU (brake actuator assembly) monitors the resistance of the power supply line at the +BS terminal. A malfunction is detected when an abnormality occurs in the +BS terminal wire harness and its connection. The skid control ECU (brake actuator assembly) then determines that resistance is present in the +BS terminal wiring when the resistance exceeds the standard value.

DTC Detection Conditions: C1241

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Diagnostic Condition

-

-

-

-

-

Malfunction Status

Vehicle speed is at least 6 km/h and the +BS terminal voltage (low voltage) is less than 9.6 V.

○

-

-

-

Vehicle speed is at least 6 km/h and the +BS terminal voltage (low voltage) is less than 6.9 V.

-

○

-

-

Vehicle speed is at least 15 km/h, the +BS terminal voltage is at least 9.6 V, the skid control ECU (brake actuator assembly) turns on more than once within a short period of time, and the power supply voltage drop relay exceeds the threshold.*

-

-

○

-

The +BS terminal voltage is below 6.7 V and the skid control ECU (brake actuator assembly) determines that the power supply voltage is abnormal.

-

-

-

○

Detection Duration

at least 1 second

at least 1 second

-

at least 0.06 seconds

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK BATTERY

(a) Check the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Make sure there is no looseness in the lock and connector connection.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-30 (+BS) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (IG1 CIRCUIT)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (IG1))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-36 (IG1) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-46 (GND1) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

OK
  1. CONFIRM DTC AGAIN

(a) Reconnect connector A42 to the skid control ECU (brake actuator assembly).

(b) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Start the engine.

(e) Perform a road test.

(f) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1241 is not output.

A

DTC C1241 is output.

B

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY