Brake Control / Dynamic Control Systems

High Power Supply Voltage Malfunction (C1417)

~4min read

DESCRIPTION

When a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and inhibits ABS operation through the fail-safe function.

This DTC is stored when the +BS terminal voltage deviates due to a malfunction in a power supply or charging system circuit, such as the battery or alternator circuit.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1417

High voltage power supply malfunction

The +BS terminal voltage is above 16.5 V for at least 1 second.

  • Battery
  • Charging system
  • Power supply circuit
  • Skid control ECU (brake actuator assembly) internal power supply circuit

WIRING DIAGRAM

Refer to DTC C1241.

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK BATTERY

(a) Check the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

OK
  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Make sure there is no looseness in the lock and connector connection.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-30 (+BS) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (IG1))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-36 (IG1) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-46 (GND1) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CONFIRM DTC AGAIN

(a) Reconnect connector A42 to the skid control ECU (brake actuator assembly).

(b) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Start the engine.

(e) Perform a road test.

(f) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1417 is not output.

A

DTC C1417 is output.

B

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY