Brake Control / Dynamic Control Systems

TRAC system does not operate

~4min read

DESCRIPTION

When the ABS, TRAC or VSC system is operating, the skid control ECU (brake actuator assembly) flashes the slip indicator light to indicate to the driver that a skid has occurred.

In VSC OFF mode, or when the TRAC and VSC systems are turned off, the multi-information display of the combination meter assembly shows the TRAC OFF message and the VSC OFF indicator light comes on to inform the driver.

When a communication malfunction with the ECM is detected, TRAC and VSC are disabled. Similarly, if a system malfunction occurs, the TRAC and VSC systems are disabled and the related indicator lights come on.

PRECAUTION / NOTICE / HINT

NOTICE:

When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

Click here

PROCEDURE

  1. BRAKING PROBLEM CHECK

(a) Check whether the slip indicator light came on when TRAC was not operating.

OK:

The slip indicator light was on.

HINT:

When a DTC is stored, the slip indicator light comes on and TRAC does not operate due to the fail-safe function.

(b) Check the operating condition of the VSC OFF switch (electric parking brake switch assembly) when TRAC did not operate.

OK:

The VSC OFF switch (electric parking brake switch assembly) was turned on to turn off TRAC when TRAC did not operate.

HINT:

When the multi-information display in the combination meter assembly shows the TRAC OFF message, TRAC does not function.

OK

END

NG
  1. CHECK DTCs

(a) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(b) Turn the ignition switch OFF.

(c) Turn the ignition switch to ON.

(d) Check the DTCs (vehicle stability control system) output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

No DTCs are output.

A

DTCs related to the vehicle stability control system are output.

B

B

REPAIR THE CIRCUITS INDICATED BY THE OUTPUT DTCS

A
  1. CHECK VEHICLE

(a) Operate the VSC OFF switch (electric parking brake switch assembly) and check that the multi-information display in the combination meter assembly shows "Traction Control Turned Off" and that the VSC OFF indicator light comes on in response to switch operation.

OK:

The multi-information display in the combination meter assembly shows "Traction Control Turned Off" and the VSC OFF indicator light comes on in response to switch operation.

NG

CHECK VSC OFF SWITCH CIRCUIT

OK
  1. PERFORM TEST MODE INSPECTION (SIGNAL CHECK) (SPEED SENSOR CIRCUIT)

(a) Using the Techstream, perform the Check Mode (Signal Check) sensor check and confirm that the speed sensor Check Mode (Signal Check) items change from Incomplete to Completed.

Click here

Chassis > ABS/VSC/TRAC/EPB > Utility

Signal Check

OK:

The speed sensor Check Mode (Signal Check) items change from Incomplete to Completed.

NG

CHECK AND REPAIR MALFUNCTIONING SPEED SENSOR CIRCUIT

OK
  1. PERFORM FUNCTION CHECK

(a) Operate the VSC OFF switch (electric parking brake switch assembly) and confirm that the system is not in TRAC OFF mode or VSC OFF mode.

(b) Confirm that no DTCs are output and that each warning light is off.

(c) Start the vehicle on a low-friction surface and check that TRAC operates when attempting to spin the drive wheels.

OK:

The TRAC system operates when wheel spin occurs during starting.

NOTICE:

  • Even when the system is operating normally, the VSC system may not operate at low vehicle speed, or the TRAC system may not operate due to a malfunction. Make sure only the drive wheels spin during the procedure.
  • When confirming that the skid control indicator flashes, do not spin the drive wheels more than necessary. Whether TRAC is activated can be checked by viewing the freeze frame data when the system is activated.
  • Be careful of the surroundings when performing the procedure and depress the accelerator pedal carefully.
OK

USE SIMULATION METHOD TO CHECK

NG

REPLACE BRAKE ACTUATOR ASSEMBLY