Brake Control / Dynamic Control Systems

System Description

~6min read

SYSTEM DESCRIPTION

FUNCTION DESCRIPTION

(a) Enhanced VSC

(1) Performs cooperative control with the power steering ECU assembly to provide power steering assistance according to vehicle driving conditions.

(b) Anti-lock Brake System (ABS)

(1) The ABS helps prevent the wheels from locking during sudden braking or braking on slippery road surfaces.

(c) Electronic Brake-force Distribution (EBD)

(1) EBD control uses the ABS to properly distribute braking force between the front and rear wheels according to driving conditions. When braking in a turn, it controls the braking force of the left and right wheels to help the driver maintain control of the vehicle.

(d) Brake Assist (BA)

(1) The main purpose of brake assist is to provide additional braking force to a driver who cannot generate sufficient braking force during emergency braking, helping to ensure the vehicle's braking performance.

(e) Traction Control (TRAC)

(1) The TRAC system helps prevent the drive wheels from spinning when the driver depresses the accelerator pedal excessively during starts or acceleration on slippery roads.

(f) Vehicle Stability Control (VSC)

(1) The VSC system helps prevent lateral skidding of the vehicle when there is a strong tendency toward understeer or oversteer while cornering.

(g) Hill-start Assist Control

(1) When starting on a hill, this control maintains brake hydraulic pressure on all 4 wheels to temporarily prevent the vehicle from rolling backward.

(h) Brake Hold System

(1) After the driver depresses the brake pedal and the vehicle comes to a stop, this function maintains brake hydraulic pressure on all 4 wheels to keep the vehicle stationary.

(i) Trailer Sway Control

(1) If the vehicle tows a trailer with an improper hitch, trailer sway may be caused by crosswinds, and imbalance may be caused by the load or the driver's operation. Trailer sway control helps reduce trailer sway by controlling engine power and the braking of each wheel.

FUNCTION OF COMPONENTS

Component

Function

Brake Actuator Assembly

Skid control ECU

Evaluates the vehicle driving condition based on signals from each sensor and sends brake control signals to the brake actuator assembly.

Master Cylinder Pressure Sensor

Built into the brake actuator assembly, detects master cylinder pressure.

Pump Motor

Controls the pumps inside the brake actuator assembly.

Solenoid Valves

  • The hydraulic circuit is equipped with 2 master cylinder cut-off solenoid valves, 2 reservoir cut-off solenoid valves, 4 pressure hold solenoid valves, and 4 pressure reduction solenoid valves.
  • Switches the fluid circuit based on signals from the skid control ECU during brake control system operation, in order to control the fluid pressure applied to each wheel cylinder.

Skid control ECU

ABS Motor Relay

Supplies power to the pump motor.

ABS Solenoid Relay

Supplies power to the solenoid valves.

Speed sensor

Detects the rotation speed of each of the four wheels.

Stop light switch assembly

Detects the brake pedal release signal.

Main body ECU (multiplex network body ECU)

Sends the parking brake signal to the skid control ECU.

Electric Parking Brake Switch Assembly

VSC OFF Switch

Allows the driver to select normal mode, TRAC OFF mode, or VSC OFF mode.

Brake Hold Switch

Enables brake hold operation.

ECM

  • Sends the throttle position signal, accelerator pedal position signal, engine speed signal, etc., to the skid control ECU.
  • Based on signals from the skid control ECU, controls the engine output power.

Airbag sensor assembly

Yaw and Acceleration Sensor

  • The airbag sensor assembly includes the yaw and acceleration sensor.
  • The yaw rate sensor detects the yaw rate of the vehicle.
  • The acceleration sensor detects the longitudinal and lateral acceleration of the vehicle.
  • The airbag sensor assembly sends detection signals from the yaw rate sensor and acceleration sensor to the skid control ECU via CAN communication.

Steering angle sensor

Detects the steering direction and steering wheel angle.

Combination meter assembly

ABS Warning Light

Illuminates to alert the driver when the skid control ECU detects a malfunction in the ABS system.

Brake Warning Light (Red)

  • Illuminates to alert the driver when the skid control ECU detects a malfunction in the EBD or brake system.
  • Illuminates to alert the driver when the brake fluid level is low.
  • Illuminates to inform the driver when the parking brake is applied.

Multi-information Display (TRAC OFF Message)

Displays an information message when TRAC OFF mode or VSC OFF mode is selected.

VSC OFF Warning Light

Illuminates to inform the driver when VSC OFF mode is selected.

Skid Control Warning Light

  • Flashes to inform the driver that the TRAC or VSC system is performing a check.
  • Illuminates to alert the driver when the skid control ECU detects a malfunction in the TRAC and/or VSC system.

Brake Hold Standby Light

Illuminates to inform the driver that the brake hold standby condition has been established.

Brake Hold Operation Light

  • Illuminates to indicate to the driver that the brake hold function is operating.
  • Flashes to alert the driver when the skid control ECU detects a malfunction in the brake hold function.

Master Cylinder Reservoir Sub-assembly

Brake Fluid Level Warning Switch

Detects the brake fluid level.

Brake Pedal Support Assembly

Brake Pedal Load Detection Switch

Detects the load applied to the brake pedal.

Millimeter Wave Radar Sensor Assembly*1

Sends brake request signals to the skid control ECU.

  • *1: with pre-collision safety system