Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the Techstream.
(f) Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
(g) Check the Data List displayed on the Techstream.
Chassis > ABS/VSC/TRAC/EPB > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
ABS Warning Light |
ABS Warning Light |
ON or OFF |
ON: Indicator on OFF: Indicator off |
- |
Brake Warning Light |
Brake Warning Light (Red) |
ON or OFF |
ON: Indicator on OFF: Indicator off |
- |
Buzzer |
Instrument cluster buzzer |
ON or OFF |
OFF: Buzzer off |
No change |
Stop Light SW |
Stop light switch |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
Parking Brake SW |
Parking Brake Switch |
ON or OFF |
ON: Parking brake applied OFF: Parking brake released |
- |
Main Idle SW |
Main Idle Switch |
ON or OFF |
ON: Accelerator pedal released OFF: Accelerator pedal depressed |
- |
Brake Pedal Load Sensing SW |
Brake Pedal Load Detection Switch |
ON or OFF |
ON: Brake pedal depressed beyond the specified point OFF: Brake pedal depressed less than the specified point |
- |
Gear Position |
Engaged gear information |
"P,N", R, 1st-8th, Fail or Not R |
Actual engaged gear |
- |
Shift Lever Position |
Shift lever position information |
"P,N", R, D/M, 1st-6th/B or Fail |
Actual shift lever position |
- |
Shift Information |
Engaged gear information |
ON or OFF |
ON: During gear shift OFF: Not during gear shift |
- |
Inspection Mode |
Inspection Mode |
Other or Inspect |
Other: Normal mode Inspect: Inspection mode |
- |
Number of IG ON(Inspection) |
Number of times the ignition switch has been turned ON after switching to inspection mode |
Min.: 0, Max.: 255 |
- |
- |
Master Cylinder Sensor |
Master cylinder pressure sensor value |
Min.: 0.00 V, Max.: 5.00 V |
Brake pedal released: 0.20 to 0.40 V |
The value increases when the brake pedal is depressed |
Deceleration Sensor |
Deceleration sensor value |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
Zero Point of Decele |
Stored zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
- |
Deceleration Sensor2 |
Deceleration sensor 2 value |
Min.: -18.525 m/s2, Max.: 18.387 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
Zero Point of Decele2 |
Stored zero value |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
- |
Yaw Rate Sensor |
Yaw rate sensor |
Min.: -128°/s, Max.: 127°/s |
Vehicle stationary: 0 °/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
Zero Point of Yaw Rate |
Stored zero value |
Min.: -128°, Max.: 127° |
- |
After zero point calibration of yaw rate sensor: 0° |
Steering Angle Sensor |
Steering angle sensor |
Min.: -3,276.8°, Max.: 3,276.7° |
Turning left: Increases Turning right: Decreases |
- |
Zero Point of Steering Angle |
Stored zero value |
Min.: -3,276.8°, Max.: 3,276.7° |
- |
After zero point calibration of steering angle sensor: 0° |
Lateral G |
Lateral G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
While turning: Changes in proportion to lateral acceleration |
Forward and Rearward G |
Forward and backward G |
Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- |
During acceleration/deceleration: Changes in proportion to acceleration |
Yaw Rate Value |
Yaw rate value |
Min.: -128°, Max.: 127° |
- |
While turning: Changes in proportion to yaw rate |
Steering Angle Value |
Steering angle value |
Min.: -3,276.8°, Max.: 3,276.7° |
- |
During steering operation: Changes in proportion to steering wheel rotation |
Stop Light Relay |
Stop light relay (stop light switch assembly) |
ON or OFF |
ON: Relay activated OFF: Relay off |
- |
Slip Indicator Light |
Skid Control Warning Light |
ON or OFF |
ON: Indicator on OFF: Indicator off |
- |
FR Wheel Speed |
Front right wheel speed sensor value |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When vehicle is driving at constant speed: No large fluctuation |
FL Wheel Speed |
Front left wheel speed sensor value |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When vehicle is driving at constant speed: No large fluctuation |
RR Wheel Speed |
Rear right wheel speed sensor value |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When vehicle is driving at constant speed: No large fluctuation |
RL Wheel Speed |
Rear left wheel speed sensor value |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When vehicle is driving at constant speed: No large fluctuation |
Vehicle Speed |
Maximum value for wheel speed sensor |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When vehicle is driving at constant speed: No large fluctuation |
FR Wheel Acceleration |
Front right wheel acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
FL Wheel Acceleration |
Front left wheel acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
RR Wheel Acceleration |
Rear right wheel acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
RL Wheel Acceleration |
Rear left wheel acceleration |
Min.: -200.84 m/s2, Max.: 199.27 m/s2 |
- |
During deceleration/acceleration: Changes continuously |
FR Wheel Direction |
Front right wheel rotation direction |
Forward or Reverse |
Forward: Forward Reverse: Reverse |
Supported if the speed sensor can transmit forward/reverse direction information (smart type) |
FL Wheel Direction |
Front left wheel rotation direction |
Forward or Reverse |
Forward: Forward Reverse: Reverse |
Supported if the speed sensor can transmit forward/reverse direction information (smart type) |
RR Wheel Direction |
Rear right wheel rotation direction |
Forward or Reverse |
Forward: Forward Reverse: Reverse |
Supported if the speed sensor can transmit forward/reverse direction information (smart type) |
RL Wheel Direction |
Rear left wheel rotation direction |
Forward or Reverse |
Forward: Forward Reverse: Reverse |
Supported if the speed sensor can transmit forward/reverse direction information (smart type) |
Stop Light Relay Output |
Stop light relay control output (stop light switch assembly) |
ON or OFF |
ON: Relay output activated (stop lights on) OFF: Relay output deactivated (stop lights off) |
- |
EBS Relay |
Stop light control relay (for emergency braking signal) |
ON or OFF |
OFF: Relay off |
No change |
FR Wheel ABS Ctrl Status |
Front right wheel ABS control status |
ON or OFF |
ON: During control |
- |
FL Wheel ABS Ctrl Status |
Front left wheel ABS control status |
ON or OFF |
ON: During control |
- |
RR Wheel ABS Ctrl Status |
Rear right wheel ABS control status |
ON or OFF |
ON: During control |
- |
RL Wheel ABS Ctrl Status |
Rear left wheel ABS control status |
ON or OFF |
ON: During control |
- |
FR Wheel EBD Ctrl Status |
Front right wheel EBD control status |
ON or OFF |
ON: During control |
- |
FL Wheel EBD Ctrl Status |
Front left wheel EBD control status |
ON or OFF |
ON: During control |
- |
RR Wheel EBD Ctrl Status |
Rear right wheel EBD control status |
ON or OFF |
ON: During control |
- |
RL Wheel EBD Ctrl Status |
Rear left wheel EBD control status |
ON or OFF |
ON: During control |
- |
BA Ctrl Status |
BA control status |
ON or OFF |
ON: During control |
- |
PBA Ctrl Status |
PBA control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Ctrl Status |
TRAC control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Engine Ctrl Status |
TRAC engine control status |
ON or OFF |
ON: During control |
- |
TRC(TRAC) Brake Ctrl Status |
TRAC brake control status |
ON or OFF |
ON: During control |
- |
FR Wheel VSC Ctrl Status |
Front right wheel VSC control status |
ON or OFF |
ON: During control |
- |
FL Wheel VSC Ctrl Status |
Front left wheel VSC control status |
ON or OFF |
ON: During control |
- |
RR Wheel VSC Ctrl Status |
Rear right wheel VSC control status |
ON or OFF |
ON: During control |
- |
RL Wheel VSC Ctrl Status |
Rear left wheel VSC control status |
ON or OFF |
ON: During control |
- |
Engine Revolutions |
Engine speed |
Min.: 0 rpm, Max.: 65,535 rpm |
Engine off: 0 rpm |
When engine speed is constant: No large variation |
Real Engine Torque |
Real Engine Torque |
Min.: -1 24 N·m, Max.: 1 23 N·m |
- |
- |
Accelerator Opening Angle % |
Accelerator Pedal Opening Angle Percentage |
Min.: 0.0%, Max.: 127.5% |
Accelerator pedal released: 0.0 % |
While accelerator pedal is operating: Changes in proportion to pedal movement |
Solenoid Relay |
ABS solenoid relay |
ON or OFF |
ON: Solenoid relay on OFF: Solenoid relay off |
- |
ECB Motor Relay |
ABS Motor Relay |
ON or OFF |
ON: Motor relay on OFF: Motor relay off |
ECB: Electronically controlled braking |
TR(A)C/VSC Solenoid (SRM2) |
Master cut-off solenoid (SRM2) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRM1) |
Master cut-off solenoid (SRM1) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRC2) |
Master cut-off solenoid (SRC2) |
ON or OFF |
ON: During control |
- |
TR(A)C/VSC Solenoid (SRC1) |
Master cut-off solenoid (SRC1) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFRH) |
ABS solenoid (SFRH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFRR) |
ABS Solenoid (SFRR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFLH) |
ABS Solenoid (SFLH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SFLR) |
ABS Solenoid (SFLR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRRH) |
ABS Solenoid (SRRH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRRR) |
ABS Solenoid (SRRR) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRLH) |
ABS Solenoid (SRLH) |
ON or OFF |
ON: During control |
- |
ABS Solenoid (SRLR) |
ABS Solenoid (SRLR) |
ON or OFF |
ON: During control |
- |
EFI Communication Open |
ECM Communication Interruption Detection |
Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
Yaw Rate Open |
Detection of yaw rate sensor open circuit |
Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
Deceleration Open |
Detection of acceleration sensor open circuit |
Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
Steering Open |
Detection of steering angle sensor open circuit |
Error or Normal |
Error: Momentary interruption Normal: Normal |
- |
IG1 Voltage Value |
IG1 Voltage Value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
+BS Voltage Value |
+BS Voltage Value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
Motor Voltage Value |
Motor Voltage Value |
Min.: 0.00 V, Max.: 20.00 V |
- |
Changes in proportion to battery voltage |
BH Standby Light |
Brake Hold Standby Light |
ON or OFF |
ON: Indicator on OFF: Indicator off |
- |
BH Operated Light |
Brake Hold Operation Light |
ON or OFF |
ON: Indicator on OFF: Indicator off |
- |
TRAC/VSC Off Mode |
TRAC/VSC OFF Mode |
Normal, TRAC OFF, VSC Expert Mode or VSC OFF |
Normal: Normal mode TRAC OFF: TRAC OFF mode VSC OFF: VSC OFF mode |
- |
Number of DTC |
Number of Registered DTCs |
Min.: 0, Max.: 255 |
- |
- |
IG Voltage Value Decreased |
Detection of +BS voltage value decrease |
Error or Normal |
Error: Low voltage Normal: Normal |
- |
IG Voltage Value Increased |
Detection of +BS voltage value increase |
Error or Normal |
Error: High voltage Normal: Normal |
- |
Hazard Switch History |
Hazard Switch History |
Incomplete or Complete |
Incomplete: Not completed Complete: Completed |
- |
Reverse Position Switch |
Reverse Position Switch |
ON or OFF |
- |
- |
DSS Signal Buzzer |
Buzzer sounds |
ON or OFF |
- |
- |
Vehicle Speed (Control Value) |
Vehicle speed (control value) |
Min.: 0 km/h Max.: 326 km/h |
- |
- |
ECU +B1 Voltage |
Skid control ECU (brake actuator assembly) +B1 voltage |
0,00 à 20,00 V |
11 à 14 V |
- |
RH Actuator Motor Input Voltage |
Right parking brake motor input voltage (right parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
RH Actuator Motor +Terminal Voltage |
Voltage on right parking brake motor positive (+) terminal side (right parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
RH Actuator Motor -Terminal Voltage |
Voltage on right parking brake motor negative (-) terminal side (right parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
LH Actuator Motor Input Voltage |
Left parking brake motor input voltage (left parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
LH Actuator Motor +Terminal Voltage |
Voltage on left parking brake motor positive (+) terminal side (left parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
LH Actuator Motor -Terminal Voltage |
Voltage on left parking brake motor negative (-) terminal side (left parking brake actuator assembly) |
0,00 à 20,00 V |
- |
- |
Indoor Temperature |
Indoor Temperature |
-6,50 à 57 °C |
- |
When the displayed value differs from the actual cabin temperature, the air conditioning system and CAN communication system may be malfunctioning |
Ambient Temperature |
Ambient Temperature |
-40 à 50 °C |
- |
When the displayed value differs from the actual ambient temperature, the air conditioning system and CAN communication system are likely malfunctioning |
EPB Switch |
Electric parking brake switch assembly input voltage |
OFF, Lock, Release or Unknown |
OFF: Lock switch and release switch are in OFF position Lock: Lock switch released: Release switch in ON position |
If not operating normally, the release side system of the electric parking brake switch assembly may malfunction HINT: EPB stands for electric parking brake. |
Auto Mode Request |
Auto Mode Request Status |
OFF or ON |
- |
- |
Shift Position |
Shift lever position |
P, N, R, D or Unknown |
P: Shift lever in P position N: Shift lever in N position R: Shift lever in R position D: Shift lever in D or M position |
- |
IG Switch |
IG power supply status |
OFF or ON |
OFF: IG power supply voltage is not supplied to skid control ECU (brake actuator assembly) ON: IG power supply voltage is supplied to skid control ECU (brake actuator assembly) |
- |
Brake Hold Ready |
Brake hold control enable status |
OFF or ON |
- |
- |
Brake Hold Control Mode |
Brake hold control mode |
OFF, ON, Release or EPB |
OFF: Brake hold control is not operating ON: Brake hold control is operating Release: Brake hold control is released EPB: Parking brake is applied during brake hold control |
HINT: EPB stands for electric parking brake. |
RH Actuator Current Status |
Right Parking Brake Actuator Assembly Current Status |
Invalid or Valid |
Valid |
- |
LH Actuator Current Status |
Left Parking Brake Actuator Assembly Current Status |
Invalid or Valid |
Valid |
- |
RH Actuator Nut Stroke |
Right Parking Brake Actuator Assembly Nut Stroke Value |
0.000 to 8.160 mm (0.000 to 0.321 in.) |
- |
- |
LH Actuator Nut Stroke |
Left Parking Brake Actuator Assembly Nut Stroke Value |
0.000 to 8.160 mm (0.000 to 0.321 in.) |
- |
- |
RH Actuator Motor Actual Current |
Right Parking Brake Motor Actual Current Value (Right Parking Brake Actuator Assembly) |
-5,0362 à 50,5000 A |
- |
- |
RH Actuator 0 load Current |
Current Value of RH Parking Brake Actuator Assembly, No Load |
-5,0362 à 50,5000 A |
- |
- |
LH Actuator Motor Actual Current |
Left Parking Brake Motor Actual Current Value (Left Parking Brake Actuator Assembly) |
-5,0362 à 50,5000 A |
- |
- |
LH Actuator 0 load Current |
Current Value of LH Parking Brake Actuator Assembly, No Load |
-5,0362 à 50,5000 A |
- |
- |
Counter of IG ON After EPB Control Cancel |
Number of times the ignition switch has been turned ON after EPB control cancellation |
0 to 255 times |
- |
- |
RH Actuator Status |
Right Parking Brake Actuator Assembly Status |
Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control |
- |
- |
LH Actuator Status |
Left Parking Brake Actuator Assembly Status |
Default, Lock, Lock Dynamic, Release, Lock Faulty, Unexpected, Lock Standby, Release Standby, Lock Dynamic Standby, Release Dynamic Standby, Lock Dynamic Faulty, Lock Standard Control, Lock Dynamic Control, Lock Control for Prevention Loosen by High Temperature, Lock Control for Prevention Slipping Down, Re-Lock Control by Switch, Recovery Lock Control, Lock Control After Dynamic PKB, Release Standard Control, Release Dynamic Control, Full Release Control |
- |
- |
Auto Mode |
AUTO Mode Permission Status (linked to shift operation) |
OFF or ON |
OFF: Manual mode. ON: AUTO mode (linked to shift operation) |
- |
Dynamic PKB Mode |
Dynamic Parking Brake Operating Status |
OFF or ON |
OFF: Dynamic parking brake is not operating ON: Dynamic parking brake is operating |
- |
Interlocking Shift Permission |
AUTO Mode Permission Status (linked to shift operation) |
OK or NG |
- |
- |
Interlocking Brake Permission |
Brake-Related Permission Status |
OK or NG |
- |
- |
RH Interlocking PKB Lock Permission |
RH Parking Brake Actuator Assembly PKB Lock Control Permission Status |
OK or NG |
- |
- |
RH Interlocking PKB Release Permission |
RH Parking Brake Actuator Assembly PKB Release Control Permission Status |
OK or NG |
- |
- |
RH Interlocking Dynamic PKB Permission |
RH Parking Brake Actuator Assembly Dynamic PKB Control Permission Status |
OK or NG |
- |
- |
RH Interlocking PKB Full Release Permission |
RH Parking Brake Actuator Assembly PKB Full Release Permission Status |
OK or NG |
- |
- |
LH Interlocking PKB Lock Permission |
RH Parking Brake Actuator Assembly PKB Lock Control Permission Status |
OK or NG |
- |
- |
LH Interlocking PKB Release Permission |
RH Parking Brake Actuator Assembly PKB Release Control Permission Status |
OK or NG |
- |
- |
LH Interlocking Dynamic PKB Permission |
RH Parking Brake Actuator Assembly Dynamic PKB Control Permission Status |
OK or NG |
- |
- |
LH Interlocking PKB Full Release Permission |
LH Parking Brake Actuator Assembly PKB Full Release Permission Status |
OK or NG |
- |
- |
Fade Status |
Fade Status |
OFF or ON |
- |
- |
EPB Control Cancel Counter |
EPB Control Cancel Counter |
0 to 7 times |
- |
HINT: EPB stands for electric parking brake. |
Parking Brake Light |
Parking Brake Warning Light Output Signal (red) |
OFF, Light or Blink |
OFF: Parking brake (red) warning light turns off Light: Parking brake (red) warning light turns on Blink: Parking brake (red) warning light flashes |
- |
EPB Warning Light |
Brake system warning light output signal (yellow light) |
OFF or ON |
OFF: Brake system warning light (yellow) turns off ON: Brake system warning light (yellow) turns on |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows operating relays, VSVs, actuators and other components without removing any parts. This non-intrusive functional check can be very useful, as intermittent operation can be identified before parts or wiring are moved.
Performing the Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the Techstream to the DLC3.
(d) Turn the ignition switch to the ON position.
(e) Turn on the Techstream.
(f) Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.
(g) Perform the Active Test by following the instructions on the Techstream.
Chassis > ABS/VSC/TRAC/EPB > Active TestTester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
ABS Warning Light |
ABS Warning Light |
OFF / ON |
Inspect the instrument cluster assembly |
Brake Warning Light |
Brake Warning Light (Red) |
OFF / ON |
Inspect the instrument cluster assembly |
Buzzer |
Instrument cluster buzzer |
OFF / ON |
Buzzer sounds |
Motor Relay |
ABS Motor Relay |
OFF / ON |
Engine operating noise is audible |
Stop Light Relay |
Stop light relay (stop light switch assembly) |
OFF / ON |
Stop lights illuminate |
ABS Solenoid (SRLR) |
ABS Solenoid (SRLR) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SRLH) |
ABS Solenoid (SRLH) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SRRR) |
ABS Solenoid (SRRR) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SRRH) |
ABS Solenoid (SRRH) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SFLR) |
ABS Solenoid (SFLR) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SFLH) |
ABS Solenoid (SFLH) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SFRR) |
ABS Solenoid (SFRR) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
ABS Solenoid (SFRH) |
ABS solenoid (SFRH) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
VSC/TRAC Solenoid (SRMR) |
Master cut-off solenoid (SRM2) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
VSC/TRAC Solenoid (SRMF) |
Master cut-off solenoid (SRM1) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
VSC/TRAC Solenoid (SRCR) |
Master cut-off solenoid (SRC2) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
VSC/TRAC Solenoid (SRCF) |
Master cut-off solenoid (SRC1) |
OFF / ON |
Solenoid valve operating noise (clicking) is audible |
BH Standby Light |
Brake Hold Standby Light |
OFF / ON |
Inspect the instrument cluster assembly |
BH Operated Light |
Brake Hold Operation Light |
OFF / ON |
Inspect the instrument cluster assembly |
TRC(TRAC) OFF Indicator Light |
Multi-information Display (TRAC OFF Message) |
OFF / ON |
Inspect the instrument cluster assembly |
VSC OFF Indicator Light |
VSC OFF Warning Light |
OFF / ON |
Inspect the instrument cluster assembly |
Slip Indicator Light |
Skid Control Warning Light |
OFF / ON |
Inspect the instrument cluster assembly |
EBS Relay |
Stop light switch assembly output (emergency braking signal operation) |
OFF / ON |
The item is displayed on the Techstream but is not used. |
TPMS Warning Light |
TPMS warning light |
OFF / ON |
Inspect the instrument cluster assembly |
ABS Solenoid |
ABS solenoid valve (SRLR, SRLH, SRRR, SRRH, SFLR, SFLH, SFRR, SFRH) |
Solenoid valve SRLR/SRLH/SRRR/ SRRH / SFLR / SFLH / SFRR / SFRH |
Solenoid valve operating noise (clicking) is audible |
VSC/TRC(TRAC) Solenoid |
Main cut-off solenoid valve (SRM1, SRM2, SRC1, SRC2) |
Solenoid valve SRMF/SRMR/SRCF/ SRCR/SMF/SMR/SPFR/SPFL |
Solenoid valve operating noise (clicking) is audible |
DSS Signal Buzzer |
Skid control buzzer |
OFF / ON |
Buzzer sounds |
Auto Mode |
AUTO mode (linked to gear change) |
ON or OFF |
|
EPB Warning Light |
Brake system warning light (yellow) |
ON or OFF |
HINT: EPB stands for electric parking brake. |
PKB Light |
Parking brake warning light (red) |
ON or OFF |
|
PKB Lock Control |
Parking brake lock control |
ON or OFF |
|
PKB Release Control |
Parking brake release control |
ON or OFF |
|
PKB Full Release Control |
Parking brake full release control |
ON or OFF |
|