Brake Control / Dynamic Control Systems

Stop Light Switch Stuck OFF (C1426)

~8min read

DESCRIPTION

The Skid Control ECU (Brake Actuator Assembly) receives signals from the stop light switch and uses them to determine whether the brakes are applied or not.

The Skid Control ECU (Brake Actuator Assembly) has a detection circuit that it uses to detect a short circuit in the stop light switch input line or the stop light circuit ground wire with the stop light switch ON (brake pedal depressed).

If the Skid Control ECU (Brake Actuator Assembly) detects a short circuit, it stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1426

Stop light switch stuck in OFF position malfunction

One of the following conditions is detected:

  • When the stop light switch is OFF and the stop light switch is ON (IG), the condition must be maintained for at least 3 seconds in order to be evaluated based on the master cylinder pressure value.
  • When the stop light switch is OFF and the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1,160 psi) for 3 seconds
  • Wire harness or connector
  • Stop light switch assembly
  • Skid control ECU (brake actuator assembly)
DTC Detection Conditions: C1426

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

-

-

-

Malfunction Status

When the stop light switch is OFF, the stop light switch is considered ON based on the master cylinder pressure value.

○

-

When the stop light switch is OFF, the master cylinder pressure is more than 8 MPa (81.6 kgf/cm2, 1,160 psi).

-

○

Detection Duration

3 seconds minimum

3 seconds minimum

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

Refer to DTC C1249.

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION

(a) Check the brake pedal height adjustment.

Click here

(b) Check the installation of the stop light switch assembly.

Click here

OK:

The brake pedal height and stop light switch installation are normal.

HINT:

If the ON/OFF status of the stop light switch assembly and the master cylinder pressure sensor pressure increase do not match due to an improperly installed brake pedal or stop light switch assembly connector, this DTC may be stored. Therefore, be sure to check the installation conditions of the pedal and connector before checking the input signals and any other related parts.

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH

OK
  1. CHECK STOP LIGHT OPERATION

(a) Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

Condition

Light Condition

Brake pedal depressed.

ON

Brake pedal released.

OFF

NG

GO TO STEP 7

OK
  1. READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Select the Data List using the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Stop Light SW

Stop light switch

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Stop Light SW

(d) Check that the stop light switch status shown on the Techstream changes according to brake pedal operation.

OK:

The Techstream shows ON or OFF according to brake pedal operation.

NG

GO TO STEP 5

OK
  1. CONFIRM DTC AGAIN

(a) Turn the ignition switch OFF.

(b) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Start the engine.

(e) Depress the brake pedal several times to test the stop light circuit.

(f) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1426 is not output.

A

DTC C1426 is output.

B

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY

  1. CHECK HARNESS AND CONNECTOR (STP TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Check that the connector lock and connection have no looseness.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Measure the voltage according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-44 (STP2) - Body ground

Stop light switch ON (brake pedal depressed)

11 à 14 V*

HINT:

*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

OK
  1. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-46 (GND1) - Body ground

Always

Below 1 Ω

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

  1. CHECK STOP LIGHT SWITCH ASSEMBLY

(a) Inspect the stop light switch assembly.

Click here

OK:

The stop light switch assembly is normal.

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

OK
  1. CHECK HARNESS AND CONNECTOR (STP TERMINAL)

(a) Make sure there is no looseness in the lock and connector connection.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-44 (STP2) - Body ground

Stop light switch ON (brake pedal depressed)

11 à 14 V*

A42-44 (STP2) - Body ground

Stop light switch OFF (brake pedal released)

Below 1.5 V

HINT:

*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)

OK
  1. CONFIRM DTC AGAIN

(a) Reconnect connector A42 to the skid control ECU (brake actuator assembly).

(b) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Start the engine.

(e) Depress the brake pedal several times to test the stop light circuit.

(f) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1426 is not output.

A

DTC C1426 is output.

B

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

A

CHECK LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

B

REPLACE BRAKE ACTUATOR ASSEMBLY