Brake Control / Dynamic Control Systems

SM Solenoid Valve Circuit (C1225-C1228,C1468,C1469,C146A,C146B)

~3min read

DESCRIPTION

These solenoid valves are activated by signals from the Skid Control ECU (Brake Actuator Assembly) and control the pressure acting on the wheel cylinders to regulate braking force.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1225

SM solenoid valve circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C1226

SA2 solenoid valve circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C1227

SA3 solenoid valve circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C1228

STR solenoid valve circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C1468

SFR Solenoid Valve Circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C1469

SFL Solenoid Valve Circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C146A

SRR Solenoid Valve Circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

C146B

SRL Solenoid Valve Circuit

The solenoid valve signal does not match the check result.

  • Solenoid Valve Circuit
  • Solenoid Valve Operation (Brake Actuator Assembly)

WIRING DIAGRAM

Refer to DTC C146E.

Click here

PROCEDURE

  1. CONFIRM DTC AGAIN

HINT:

These DTCs are output when a malfunction is detected in the Skid Control ECU (Brake Actuator Assembly).

The solenoid valve circuits are built into the Skid Control ECU (Brake Actuator Assembly).

Under these conditions, it is impossible to check the solenoid valve itself or its circuit. Be sure to check whether any DTCs are output again before replacing the Skid Control ECU (Brake Actuator Assembly).

(a) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(b) Turn the ignition switch OFF.

(c) Start the engine.

(d) Drive the vehicle at a speed of at least 20 km/h.

(e) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B are not output.

A

DTCs C1225, C1226, C1227, C1228, C1468, C1469, C146A and C146B are output.

B

HINT:

  • The Skid Control ECU (Brake Actuator Assembly) performs a self-diagnosis of the solenoid valve circuit when the ignition switch is turned ON.
  • If a normal system code is output (no malfunction code is output), lightly shake the connectors, wire harnesses and fuses of the brake actuator assembly.
  • If a DTC is output while shaking the connector or wire harness of the Skid Control ECU (Brake Actuator Assembly), check and repair the connector or wire harness.
  • If no DTC is output, check for intermittent problems, as the DTC may have been stored due to a poor connection at the connector terminal.
A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY