Brake Control / Dynamic Control Systems

Master Cylinder Pressure Sensor Malfunction (C1246)

~5min read

DESCRIPTION

The master cylinder pressure sensor is built into the brake actuator assembly and connected to the skid control ECU.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1246

Master cylinder pressure sensor malfunction

One of the following conditions is detected:

  • The sensor signal voltage is out of range (less than 0.129 V or greater than 3.29 V).
  • A malfunction is detected in the internal sensor check of the skid control ECU.
  • The sensor signal offset value is outside the allowable range.
  • Stop Light Switch Circuit
  • Master Cylinder Pressure Sensor Circuit
  • Master Cylinder Pressure Sensor (Brake Actuator Assembly)
DTC detection conditions:

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Diagnostic Condition

-

-

-

-

Malfunction Status

The sensor signal voltage is out of range (less than 0.129 V or greater than 3.29 V).

○

-

-

A malfunction is detected in the internal sensor check of the skid control ECU.

-

○

-

The sensor signal offset value is outside the allowable range.

-

-

○

Detection Duration

-

-

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

Click here

PROCEDURE

  1. CHECK STOP LIGHT OPERATION

(a) Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

OK:

Condition

Light Condition

Brake pedal depressed.

ON

Brake pedal released.

OFF

NG

CHECK LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

OK
  1. READ VALUE USING TECHSTREAM (MASTER CYLINDER PRESSURE SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Select the Data List using the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Master Cylinder Sensor

Master cylinder pressure sensor value

Min.: 0.00 V, Max.: 5.00 V

When brake pedal is released: 0.2 to 0.4 V

The value increases when the brake pedal is depressed

Chassis > ABS/VSC/TRAC/EPB > Data List

Master Cylinder Sensor

(d) Check that the brake fluid pressure value shown by the master cylinder pressure sensor on the Techstream changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage shown on the Techstream increases.

NG

REPLACE BRAKE ACTUATOR ASSEMBLY

OK
  1. READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Select the Data List using the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Stop Light SW

Stop light switch

ON or OFF

ON: Brake pedal depressed

OFF: Brake pedal released

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Stop Light SW

(d) Check that the stop light switch status shown on the Techstream changes according to brake pedal operation.

OK:

The Techstream shows ON or OFF according to brake pedal operation.

NG

GO TO STEP 5

OK
  1. CONFIRM DTC AGAIN

(a) Turn the ignition switch OFF.

(b) Clear the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Clear DTCs

(c) Turn the ignition switch to OFF.

(d) Start the engine.

(e) Drive the vehicle and release the brake pedal several times to test the stop light circuit.

(f) Check whether the same DTC is output.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

DTC C1246 is not output.

A

DTC C1246 is output.

B

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

A

USE SIMULATION METHOD TO CHECK

B

REPLACE BRAKE ACTUATOR ASSEMBLY

  1. CHECK HARNESS AND CONNECTOR (STP TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Check that the connector lock and connection have no looseness.

(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(d) Measure the voltage according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-44 (STP2) - Body ground

Stop light switch ON (brake pedal depressed)

11 à 14 V*

A42-44 (STP2) - Body ground

Stop light switch OFF (brake pedal released)

Below 1.5 V

HINT:

*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.

HINT:

If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.

Click here

OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)