Decrease in Braking Function Performance (C1441)
DESCRIPTION
The skid control ECU judges that a brake malfunction has occurred based on the signals from the brake pedal depressed (load detection) switch and the master cylinder pressure sensor.
NOTICE:
Do not intentionally stop the engine while driving. Even if no malfunction has occurred in the brake system, DTC C1441 is stored when a malfunction is detected in the brake system due to a reduction in vacuum.
DTCs may be stored in any of the following situations:
- The brake pedal depressed (load detection) switch is defective (out of specification).
- When the brake pedal is depressed while the vehicle is moved with the engine stopped and the ignition switch ON.
- Bleeding is performed when the engine is running or the ignition switch is ON.
- The accelerator and brake pedals are depressed at the same time.*
HINT:
*: The skid control ECU may store this DTC if a malfunction is detected during evaluation while the ignition switch is ON and the accelerator pedal and brake pedal are depressed at the same time. However, this does not necessarily indicate a malfunction.
DTC No. | Detection Item | DTC Detection Condition | Suspected Area |
|---|---|---|---|
C1441 |
Braking function performance decreased |
When the brake pedal load detection switch and the master cylinder pressure sensor are operating normally, and the brake pedal load detection switch is determined to be ON, the pressure signal from the master cylinder pressure sensor does not indicate an increase. |
|
PROCEDURE
CHECK BRAKE PEDAL AND ACCELERATOR PEDAL OPERATION
(a) Ask the customer whether the pedals were depressed at the same time, while the vehicle was moving, or during braking.
OK:
The pedals were not depressed at the same time.
HINT:
The skid control ECU may record this DTC if it detects a malfunction in the evaluation, which is stuck ON when the accelerator pedal and brake pedal are depressed at the same time. If the pedals were depressed at the same time, be sure to clear the DTCs, as this is not a malfunction.
| NG | END |
|
CHECK DTCs AND FREEZE FRAME DATA
(a) Check and record DTCs and freeze frame data (click here
to check for any DTCs and click here
for freeze frame data).
HINT:
- Record the freeze frame data at the time DTC C1441 was stored, refer to the operation history, and confirm the operating conditions.
- When recording the freeze frame data to confirm the operating conditions, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".
|
CLEAR DTCs
(a) Clear the DTCs and freeze frame data (click here
to clear the DTCs and click here
for freeze frame data).
|
CHECK BRAKE PEDAL OPERATION
(a) Based on the customer's description of the problem, confirm the position of the brake pedal when it was depressed.
Result:
Result | Proceed to |
|---|---|
The brake pedal is depressed heavily. |
A |
The brake pedal is very easy to depress. |
B |
None of the above conditions. (The problem symptom does not occur.) |
C |
| B | GO TO STEP 6 |
| C | GO TO STEP 7 |
|
CHECK BRAKE BOOSTER ASSEMBLY
(a) Check the brake booster assembly.
Click here![]()
Result:
Result | Proceed to |
|---|---|
The brake booster assembly is malfunctioning. |
A |
The brake booster assembly is normal. |
B |
HINT:
If the result indicates that the brake booster assembly is defective, check the component parts related to the system, such as the brake booster, vacuum check valve, vacuum relief switch assembly (for 6AR-FSE), check valve grommet, brake booster gasket, vacuum hose and intake system, for vacuum leaks or blockage.
| A | CHECK COMPONENT PARTS (FOR VACUUM LEAKS OR BLOCKAGE) |
| B | GO TO STEP 7 |
CHECK BRAKE FLUID LEVEL
(a) Make sure the brake fluid level is sufficient.
HINT:
- If the fluid level is decreasing, check for brake fluid leaks and repair as necessary.
- Check for brake fluid leaks (brake master cylinder, brake line, hose, brake actuator, wheel cylinders, etc.).
Result:
Result | Proceed to |
|---|---|
The brake fluid level is not sufficient. |
A |
The brake fluid level is sufficient. |
B |
HINT:
If no brake fluid leaks are found at components such as the brake master cylinder, brake line, hose, brake actuator or wheel cylinders, but the fluid level is decreasing, the brake master cylinder may have an internal leak. Therefore, replace the brake master cylinder and check the brake pedal operation again.
| A | CHECK AND REPAIR ANY BRAKE FLUID LEAKS |
|
CONFIRM DTC AGAIN
(a) Clear the DTCs.
Click here![]()
(b) Start the engine.
(c) Perform a road test.
NOTICE:
Do not deliberately stop the engine while driving. DTC C1441 is stored if the brake pedal is depressed while the vehicle is moving and the engine is not running with the ignition switch ON.
(d) Check whether the same DTC is stored.
Click here![]()
Result:
Result | Proceed to |
|---|---|
DTC C1441 is not output. |
A |
DTC C1441 and other DTCs are output. |
B |
Only DTC C1441 is output. |
C |
HINT:
- If DTC C1441 and other DTCs are output at the same time, the other DTCs may be causing the engine malfunction, which resulted in DTC C1441 being output. Record the freeze frame data to confirm the malfunctioning parts, and repair the affected part.
- When recording the freeze frame data to confirm the malfunctioning parts, the following items can be confirmed: "F# or R# Wheel Speed", "Vehicle Speed", "Real Engine Torque" and "Accelerator Opening Angle %".
| A | END |
| B | CHECK AND REPLACE THE MALFUNCTIONING PART |
|
CHECK BRAKE PEDAL BRACKET ASSEMBLY
(a) Make sure the alignment marks on the brake pedal load detection switch adjustment part are correctly aligned with the alignment marks on the brackets, nuts, adjusting bolt, etc. OK: The alignment marks on the brake pedal load detection switch adjustment part are correctly aligned with the alignment marks on the brackets, nuts, adjusting bolt, etc. |
|
| OK | REPLACE BRAKE ACTUATOR ASSEMBLY |
| NG | REPLACE BRAKE PEDAL SUPPORT SUB-ASSEMBLY |
