Check / Clear DTCs
CHECK / CLEAR DTCs
DTC CHECK/CLEAR (using TECHSTREAM)
(a) Check the DTCs.
(1) Turn the ignition switch OFF.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to the ON position.
(4) Turn on the Techstream.
(5) Read the DTCs by following the instructions on the Techstream screen. Select the following menu items: Chassis / ABS/VSC/TRAC/EPB / Trouble Codes.
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes(6) Check the details of the DTCs.
Click here
![]()
NOTICE:
The vehicle stability control system outputs DTCs for the following system. When DTCs other than those in the vehicle stability control system DTC chart are output, refer to the DTC chart for the corresponding system.
System | Proceed to |
|---|---|
Electric parking brake system |
(b) Clear the DTCs.
(1) Turn the ignition switch OFF.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to the ON position.
(4) Turn on the Techstream.
(5) Operate the Techstream to clear the codes. Select the following menu items: Chassis / ABS/VSC/TRAC/EPB / Trouble Codes.
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs(6) Press the DTC clear button.
DTC CHECK/CLEAR (using SST check wire)
(a) Check the DTCs.
(1) Turn the ignition switch OFF.
(2) Using the SST, connect terminals TC and CG of the DLC3.
SST: 09843-18040
*a |
Front view of DLC3 |
(3) Turn the ignition switch to the ON position.
(4) Observe the flashing pattern of the ABS warning light, the skid control warning light and the standby brake hold warning light to identify the DTC.
HINT:
If no code is output, check the circuit between terminals TC and CG and the circuits of the ABS warning light, skid control warning lights and standby brake hold warning light.
Suspected Area | See procedure |
|---|---|
TC and CG terminal circuit |
|
ABS Warning Light Circuit (Remains On) |
|
ABS Warning Light Circuit (Does Not Come On) |
|
Skid Control Warning Light Circuit (Remains On) |
|
Skid Control Warning Light Circuit (Does Not Come On) |
|
Brake Hold Standby Light Circuit |
(5) Count the number of flashes of the ABS and skid control warning lights.
HINT:
- When the system is operating normally, each warning light flashes continuously, 0.25 seconds on and 0.25 seconds off.
- When a DTC is output, each warning light outputs the same code at 4 second intervals (for example, code 21 is output as 2 flashes, a 1.5 second pause, and 1 flash).
- When 2 or more DTCs are output, each warning light outputs a different code at 2.5 second intervals, and after all codes have been output, a 4 second pause is observed before the sequence repeats.
- When multiple codes are stored, they are output in order, starting with the DTC with the lowest number.
- If the brake hold operation warning light is flashing before the DLC3 terminals are connected, when DLC3 terminals 13 (TC) and 4 (CG) are connected, the brake hold operation warning light stops flashing and turns off.
(6) Check the details of the DTCs.
ABS DTCABS Warning Light Display | Tester display |
|---|---|
11 |
C146E |
13 |
C146C |
21 |
C1468 |
22 |
C1469 |
23 |
C146A |
24 |
C146B |
25 |
C1225 |
26 |
C1226 |
27 |
C1227 |
28 |
C1228 |
31 |
C1464 |
32 |
C1465 |
33 |
C1466 |
34 |
C1467 |
35 |
C1330 |
36 |
C1331 |
37 |
C1237 |
38 |
C1332 |
39 |
C1333 |
41 |
C1241 |
C1417 |
|
43 |
C1243 |
44 |
C1419 |
C1420 |
|
C1474 |
|
45 |
C1245 |
46 |
C1246 |
49 |
C1249 |
C1425 |
|
C1426 |
|
51 |
C1428 |
62 |
C1300 |
67 |
C1429 |
C1430 |
|
C1431 |
|
94 |
U0073 |
97 |
C1381 |
Skid Control Warning Light Display | Tester display |
|---|---|
28 |
C1472 |
C1474 |
|
31 |
C1432 |
C1433 |
|
C1434 |
|
C1439 |
|
C1445 |
|
32 |
C1419 |
C1420 |
|
34 |
C1234 |
C1435 |
|
C1436 |
|
39 |
C1336 |
43*1 |
- |
44 |
C1224 |
51 |
C1201 |
62 |
U0123 |
63 |
U0126 |
64 |
C1380 |
65 |
U0100 |
6A*2 |
C1381 |
88 |
C1288 |
98 |
C1448 |
- |
C1441 |
Warning Light Display | Tester display |
|---|---|
11*3 |
- |
14*4 |
- |
58 |
U0142 |
- *1: This DTC is output when the VSC system detects a malfunction in the ABS system.
- *2: The warning light flashes 6 times, turns off for 1.5 seconds, then flashes 10 times.
- *3: This DTC is output when the brake hold system detects a malfunction in the VSC system.
- *4: This DTC is output when the brake hold system detects a malfunction in the EPB system.
(7) After completing the inspection, disconnect the TC and CG terminals from the DLC3 to turn off the display.
If 2 or more DTCs are detected at the same time, they are displayed in ascending order.
(b) Clear the DTCs.
(1) Turn the ignition switch OFF.
(2) Using the SST, connect terminals TC and CG of the DLC3.
SST: 09843-18040
*a |
Front view of DLC3 |
(3) Turn the ignition switch to the ON position.
(4) Clear the DTCs stored in the ECU by depressing the brake pedal at least 8 times within 5 seconds.
(5) Make sure the ABS and skid control warning lights indicate the normal system code.
(6) Remove the SST from the DLC3 terminals.
HINT:
DTCs cannot be cleared by disconnecting the battery terminal or the ECU-IG No. 1 fuse.
END OF INSPECTION / DTC CLEARING
(a) Turn the ignition switch to ON.
(b) Make sure the ABS and skid control warning lights turn off approximately 3 seconds after the ignition switch is turned ON.
.gif)