Brake Control / Dynamic Control Systems

Brake Warning Light Remains On

~6min read

DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter via CAN communication.

The brake system warning light (red warning light) remains on when one of the following conditions is detected:

  • The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
  • The brake fluid level is low.
  • The vacuum inside the brake booster decreases. (with vacuum warning switch)
  • EBD does not function.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

Result:

Result

Proceed to

No DTCs are output.

A

DTCs are output.

B

B

INSPECT CAN COMMUNICATION SYSTEM

A
  1. CHECK THAT BRAKE ACTUATOR ASSEMBLY CONNECTOR IS PROPERLY CONNECTED

(a) Check that the skid control ECU (brake actuator assembly) connector is properly connected.

OK:

The connector is correctly connected.

NG

CONNECT CONNECTOR TO ECU PROPERLY

OK
  1. CHECK BATTERY

(a) Check the battery voltage.

Standard voltage:

11 à 14 V

NG

CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (+BS))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-30 (+BS) - Body ground

Always

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (POWER SOURCE TERMINAL (IG1))

(a) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

A42-36 (IG1) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

(a) Turn the ignition switch OFF.

*a

Front view of wire harness side connector

(to Skid Control ECU (Brake Actuator Assembly))

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A42-46 (GND1) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

OK
  1. CHECK BRAKE FLUID LEVEL WARNING SWITCH

(a) Turn the ignition switch OFF.

*a

Component without wire harness connected

(Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly))

(b) Remove the reservoir cap and strainer.

(c) Disconnect the A60 connector from the brake fluid level warning switch.

(d) Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position changes according to the brake fluid level.

Standard resistance:

Tester Connection

Condition

Specified Condition

1 (+) - 2 (E)

Switch OFF (float in up position)

1.9 to 2.1 kΩ

1 (+) - 2 (E)

Switch ON (float in down position)

Below 1 Ω

HINT:

If no problem is found after the above inspection, set the brake fluid level to the MAX level.

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

(a) Disconnect the connector from the combination meter assembly F4.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F4-12 (SW) - A60-1 (+)

Always

Below 1 Ω

F4-12 (SW) or A60-1 (+) - Body ground

Always

10 kΩ minimum

A60-2 (E) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK VACUUM WARNING SWITCH ASSEMBLY

(a) Check the vacuum warning switch assembly.

Click here

OK:

The vacuum warning switch assembly operates normally.

NG

REPLACE VACUUM WARNING SWITCH ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (BRAKE WARNING LIGHT CIRCUIT)

(a) Disconnect the F5 connector from the combination meter.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F5-2 (VCM) - A31-2 (+)

Always

Below 1 Ω

F5-2 (VCM) or A31-2 (+) - Body ground

Always

10 kΩ minimum

A31-1 (E) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

(a) Reconnect the A41 connector of the skid control ECU (brake actuator assembly).

(b) Select the Data List on the Techstream.

Click here

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Brake Warning Light

Brake Warning Light (Red)

ON or OFF

ON: Indicator on

OFF: Indicator off

-

Chassis > ABS/VSC/TRAC/EPB > Data List

Brake Warning Light

(c) Check the Techstream display condition of the brake system warning light (red warning light).

Result:

Result

Proceed to

The message "ON" is displayed.

A

OFF is displayed.

B

A

REPLACE BRAKE ACTUATOR ASSEMBLY

B

CHECK METER / GAUGE SYSTEM