Open in Stop Light Switch Circuit (C1425)
DESCRIPTION
The Skid Control ECU (Brake Actuator Assembly) receives signals from the stop light switch and uses them to determine whether the brakes are applied or not.
The Skid Control ECU (Brake Actuator Assembly) has a detection circuit that it uses to detect an open in the stop light switch input line.
If the Skid Control ECU (Brake Actuator Assembly) detects an open circuit, it stores this DTC.
DTC No. | Detection Item | DTC Detection Condition | Suspected Area |
|---|---|---|---|
C1425 |
Open circuit in stop light switch circuit |
An open in the stop light switch input line continues for at least 3 seconds. |
|
WIRING DIAGRAM
Refer to DTC C1249.
Click here![]()
PRECAUTION / NOTICE / HINT
NOTICE:
- When replacing the Skid Control ECU (Brake Actuator Assembly), perform system variant coding.
Click here
.gif)
- Check the fuses for the circuits related to this system before performing the following procedure.
PROCEDURE
CHECK STOP LIGHT SWITCH OPERATION
(a) Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
OK:
Condition | Light Condition |
|---|---|
Brake pedal depressed. |
ON |
Brake pedal released. |
OFF |
| NG | GO TO STEP 5 |
|
READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH ASSEMBLY)
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Select the Data List using the Techstream.
Click here![]()
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Stop Light SW |
Stop light switch |
ON or OFF |
ON: Brake pedal depressed OFF: Brake pedal released |
- |
Stop Light SW
(d) Check that the stop light switch status shown on the Techstream changes according to brake pedal operation.
OK:
The Techstream shows ON or OFF according to brake pedal operation.
| NG | GO TO STEP 4 |
|
CONFIRM DTC AGAIN
(a) Turn the ignition switch OFF.
(b) Clear the DTCs.
Click here![]()
(c) Turn the ignition switch to OFF.
(d) Start the engine.
(e) Depress the brake pedal several times to test the stop light circuit.
(f) Check whether the same DTC is output.
Click here![]()
Result:
Result | Proceed to |
|---|---|
DTC C1425 is not output. |
A |
DTC C1425 is output. |
B |
HINT:
If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.
Click here![]()
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE BRAKE ACTUATOR ASSEMBLY |
CHECK HARNESS AND CONNECTOR (STP TERMINAL)
(a) Turn the ignition switch OFF. |
|
(b) Check that the connector lock and connection have no looseness.
(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).
(d) Measure the voltage according to the value(s) specified in the table below.
Standard voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A42-44 (STP2) - Body ground |
Stop light switch ON (brake pedal depressed) |
11 à 14 V* |
A42-44 (STP2) - Body ground |
Stop light switch OFF (brake pedal released) |
Below 1.5 V |
HINT:
*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.
HINT:
If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.
Click here![]()
| A | REPLACE BRAKE ACTUATOR ASSEMBLY |
| B | REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT) |
CHECK STOP LIGHT SWITCH ASSEMBLY
(a) Inspect the stop light switch assembly.
Click here![]()
OK:
The stop light switch assembly is normal.
| NG | REPLACE STOP LIGHT SWITCH ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (STP TERMINAL)
(a) Reconnect connector A45 of the stop light switch assembly. |
|
(b) Check that the connector lock and connection have no looseness.
(c) Disconnect connector A42 from the skid control ECU (brake actuator assembly).
(d) Measure the voltage according to the value(s) specified in the table below.
Standard voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A42-44 (STP2) - Body ground |
Stop light switch ON (brake pedal depressed) |
11 à 14 V* |
A42-44 (STP2) - Body ground |
Stop light switch OFF (brake pedal released) |
Below 1.5 V |
HINT:
*: The standard value varies depending on the voltage at terminal +BS. The standard voltage is 85% of the voltage at terminal +BS.
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT) |
|
CONFIRM DTC AGAIN
(a) Reconnect connector A42 to the skid control ECU (brake actuator assembly).
(b) Clear the DTCs.
Click here![]()
(c) Turn the ignition switch to OFF.
(d) Start the engine.
(e) Drive the vehicle and release the brake pedal several times to test the stop light circuit.
(f) Check whether the same DTC is output.
Click here![]()
Result:
Result | Proceed to |
|---|---|
DTC C1425 is not output. |
A |
DTC C1425 is output. |
B |
HINT:
If troubleshooting was performed according to the symptom chart, refer to the chart and go to the next step before replacing parts.
Click here![]()
| A | USE SIMULATION METHOD TO CHECK |
| B | CHECK LIGHTING SYSTEM (STOP LIGHT CIRCUIT) |
.png)