ACC Monitor Malfunction (B2274). STSW Monitor Malfunction (B2275). Detecting Vehicle Submersion (B2277)
ACC Monitor Malfunction (B2274)
DESCRIPTION
This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit between terminal ACCD of the certification ECU (smart key ECU assembly) and the ACC relay.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2274 |
ACC Monitor Malfunction |
The ACC relay circuit of the certification ECU (smart key ECU assembly) is malfunctioning. (1-trip detection logic*) HINT: When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning. |
|
|
- *: Only detected while a malfunction is present.
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
HINT: The power switch can be turned on (IG) and the hybrid control system can be started. |
- |
DTC No. | Data List and Active Test |
|---|---|
B2274 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Inspect the fuses of circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY), AUXILIARY BATTERY AND BODY GROUND)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the 4A, 4D and 4K instrument panel junction block assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-16 (ACCD) - 4A-30 |
Always |
Below 1 Ω |
4D-3 - Body ground |
Always |
Below 1 Ω |
G40-16 (ACCD) or 4A-30 - Other terminals and body ground |
Always |
10 kΩ or higher |
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4K-1 - Body ground |
Power switch off |
11 to 14 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)
(a) Remove the instrument panel junction block assembly.
Click here ![]()
(b) Connect all of the instrument panel junction block assembly connectors.
(c) Connect the G40 certification ECU (smart key ECU assembly) connector.
(d) Measure the voltage according to the value(s) in the table below.
*a |
Component with harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-26 - Body ground |
Power switch on (ACC) |
11 to 14 V |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | END (TEMPORARY CONNECTION FAILURE IS SUSPECTED) |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
STSW Monitor Malfunction (B2275)
DESCRIPTION
This DTC is stored when a malfunction is detected in the starter circuit inside the certification ECU (smart key ECU assembly).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2275 |
STSW Monitor Malfunction |
Certification ECU (smart key ECU assembly) internal HV activation request output circuit malfunction or external circuit malfunction (1-trip detection logic*) |
|
|
- *: Only detected while a malfunction is present and the power switch is on (IG).
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
|
- |
DTC No. | Data List and Active Test |
|---|---|
B2275 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the hybrid vehicle control ECU or certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK FOR DTC
(a) Turn the power switch on (IG) and wait 25 seconds.
(b) Using the Techstream, check for certification ECU (smart key ECU assembly) DTCs.
Body Electrical > Power Source Control > Trouble CodesOK:
DTC B2285 is not output simultaneously.
| NG | GO TO DTC B2285 |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G46 hybrid vehicle control ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-27 (ST2) - G46-9 (ST2) |
Always |
Below 1 Ω |
G40-27 (ST2) or G46-9 (ST2) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Reconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Reconnect the G46 hybrid vehicle control ECU connector.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-27 (ST2) - Body ground |
With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released |
8.5 V or higher → 1 V or less |
| OK | REPLACE HYBRID VEHICLE CONTROL ECU |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Detecting Vehicle Submersion (B2277)
DESCRIPTION
This DTC is stored when a malfunction in the water submersion detection circuit inside the certification ECU (smart key ECU assembly) is detected.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2277 |
Detecting Vehicle Submersion |
Water submersion detected by the water submersion detection circuit inside the certification ECU (smart key ECU assembly). (1-trip detection logic*) |
Certification ECU (smart key ECU assembly) |
|
- *: Only detected while a malfunction is present.
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The power switch cannot be turned off and the hybrid control system cannot be started. |
- |
DTC No. | Data List and Active Test |
|---|---|
B2277 |
- |
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
Before proceeding with troubleshooting, check if there are any signs of water damage to the certification ECU (smart key ECU assembly). If there are any signs of water damage, replace the certification ECU (smart key ECU assembly) and take measures against the cause of the water damage.
PROCEDURE
CHECK WATER INTRUSION
(a) Check that the certification ECU (smart key ECU assembly), its ground area and wire harnesses have no signs of water intrusion.
Result | Proceed to |
|---|---|
No sign of water intrusion found |
A |
Signs of water intrusion found |
B |
| A | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| B | TAKE MEASURES AGAINST WATER INTRUSION AND REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
