Center Airbag Sensor Assembly
Components
COMPONENTS
ILLUSTRATION
*A |
for Gasoline Model |
- |
- |
*1 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*2 |
REAR SEAT CUSHION ASSEMBLY |
*3 |
REAR SEAT CUSHION LOCK HOOK |
- |
- |
● |
Non-reusable part |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*1 |
CENTER PILLAR LOWER GARNISH LH |
*2 |
COWL SIDE TRIM SUB-ASSEMBLY LH |
*3 |
FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
*4 |
FRONT DOOR SCUFF PLATE LH |
*5 |
NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
*6 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*7 |
REAR DOOR SCUFF PLATE LH |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*1 |
CENTER PILLAR LOWER GARNISH RH |
*2 |
COWL SIDE TRIM SUB-ASSEMBLY RH |
*3 |
FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
*4 |
FRONT DOOR SCUFF PLATE RH |
*5 |
NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY |
*6 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
*7 |
REAR DOOR SCUFF PLATE RH |
- |
- |
ILLUSTRATION
*1 |
ACCELERATOR PEDAL |
*2 |
ACCELERATOR PEDAL PAD |
*3 |
FRONT FLOOR CARPET ASSEMBLY |
*4 |
FRONT FLOOR CARPET CLIP |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
AIRBAG ECU ASSEMBLY |
*2 |
NO. 1 CONSOLE BOX DUCT |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL AIRBAG ECU ASSEMBLY
(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Install the airbag ECU assembly with the 3 bolts. Torque: 17,5 N·m {178 kgf·cm, 13 ft·lbf} NOTICE:
|
![]() |
(d) Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connectors.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
*a |
Lock Lever |
![]() |
Move in this Direction |
(e) Check that there is no looseness in the installed parts of the airbag ECU assembly.
2. INSTALL NO. 1 CONSOLE BOX DUCT
(a) Install the No. 1 console box duct with the clip as shown in the illustration.
![]() |
Install in this Direction |
3. INSTALL FRONT FLOOR CARPET ASSEMBLY
(a) Install the front floor carpet assembly to its original position as shown in the illustration. |
![]() |
(b) Engage the 2 guides.
(c) Install the 3 front floor carpet clips.
(d) Install the front floor carpet assembly to its original position as shown in the illustration. |
![]() |
(e) Engage the 2 guides.
(f) Install the 3 front floor carpet clips.
4. INSTALL ACCELERATOR PEDAL
for 2GR-FKS: Click here ![]()
for A25A-FXS: Click here ![]()
5. INSTALL ACCELERATOR PEDAL PAD
for 2GR-FKS: Click here ![]()
for A25A-FXS: Click here ![]()
6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
7. INSTALL CENTER PILLAR LOWER GARNISH LH
Click here ![]()
8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
9. INSTALL REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here ![]()
10. INSTALL REAR DOOR SCUFF PLATE LH (for HV Model)
Click here ![]()
11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
Click here ![]()
13. INSTALL FRONT DOOR SCUFF PLATE LH
Click here ![]()
14. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
15. INSTALL CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
16. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
17. INSTALL REAR DOOR SCUFF PLATE RH (for Gasoline Model)
HINT:
Use the same procedure as for the LH side.
Click here ![]()
18. INSTALL REAR DOOR SCUFF PLATE RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
Click here ![]()
19. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
21. INSTALL FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
22. INSTALL REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here ![]()
23. INSTALL REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here ![]()
24. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here ![]()
25. INSTALL CONSOLE ASSEMBLY
Click here ![]()
26. INSTALL FRONT SEAT ASSEMBLY
(a) Install the front seat assembly LH and front seat assembly RH.
Click here ![]()
27. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
28. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION
(a) When the airbag ECU assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
HINT:
The yaw rate and acceleration sensor is built into the airbag ECU assembly.
On-vehicle Inspection
ON-VEHICLE INSPECTION
CAUTION:
Be sure to correctly follow the removal and installation procedures for the airbag ECU assembly.
PROCEDURE
1. INSPECT AIRBAG ECU ASSEMBLY (for Vehicle not Involved in Collision)
(a) Perform a diagnostic system check.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
2. INSPECT AIRBAG ECU ASSEMBLY (for Vehicle Involved in Collision and Airbag not Deployed)
(a) Perform a diagnostic system check.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
(b) Visually check for defects with the airbag ECU assembly installed to the vehicle.
HINT:
The defects are as follows:
- Cracks in the ECU housing
- Dents in the ECU housing
- Chips in the ECU housing
- Cracks or other damage to the connectors
- Peeling of the label
OK:
No defects are found.
If any defects are found, replace the airbag ECU assembly with a new one.
3. INSPECT AIRBAG ECU ASSEMBLY (for Vehicle Involved in Collision and Airbag is Deployed)
(a) Replace the airbag ECU assembly.
HINT:
The airbag ECU assembly should be replaced after any of the SRS parts has deployed, as it has been subjected to an impact.
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag ECU assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Replacement of the airbag ECU assembly |
Perform system variant learning and acceleration sensor zero point calibration |
|
|
Removal/installation of the front passenger seat |
Zero point calibration (Occupant Classification System) |
|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Replacement of the airbag ECU assembly |
|
|
|
Removal/installation of the front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for Gasoline Model: Click here ![]()
for HV Model: Click here ![]()
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE FRONT SEAT ASSEMBLY
(a) Remove the front seat assembly LH and front seat assembly RH.
Click here ![]()
3. REMOVE CONSOLE ASSEMBLY
Click here ![]()
4. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Gasoline Model)
Click here ![]()
5. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here ![]()
6. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here ![]()
7. REMOVE FRONT DOOR SCUFF PLATE LH
Click here ![]()
8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here ![]()
9. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the center pillar lower garnish LH.
10. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here ![]()
11. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)
Click here ![]()
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Disconnect the rear door opening trim weatherstrip LH to the extent that allows the removal of the center pillar lower garnish LH.
13. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here ![]()
14. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
15. REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
16. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
17. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the center pillar lower garnish RH.
18. REMOVE REAR DOOR SCUFF PLATE RH (for Gasoline Model)
HINT:
Use the same procedure as for the LH side.
Click here ![]()
19. REMOVE REAR DOOR SCUFF PLATE RH (for HV Model)
HINT:
Use the same procedure as for the LH side.
Click here ![]()
20. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Disconnect the rear door opening trim weatherstrip RH to the extent that allows the removal of the center pillar lower garnish RH.
21. REMOVE CENTER PILLAR LOWER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
22. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here ![]()
23. REMOVE ACCELERATOR PEDAL PAD
for 2GR-FKS: Click here ![]()
for A25A-FXS: Click here ![]()
24. REMOVE ACCELERATOR PEDAL
for 2GR-FKS: Click here ![]()
for A25A-FXS: Click here ![]()
25. DISCONNECT FRONT FLOOR CARPET ASSEMBLY
(a) Remove the front floor carpet clip. |
![]() |
(b) Remove the 2 front floor carpet clips. |
![]() |
(c) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration. |
![]() |
(d) Remove the front floor carpet clip. |
![]() |
(e) Remove the 2 front floor carpet clips. |
![]() |
(f) Disengage the 2 guides and turn back the front floor carpet assembly as shown in the illustration. |
![]() |
26. REMOVE NO. 1 CONSOLE BOX DUCT
(a) Remove the clip.
![]() |
Remove in this Direction |
(b) Remove the No. 1 console box duct as shown in the illustration.
27. REMOVE AIRBAG ECU ASSEMBLY
(a) Check that the engine switch (for Gasoline Model) or power switch (for HV Model) is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Push down the part (A) in the direction indicated by the arrow (1) to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connectors.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
*a |
Lock Lever |
![]() |
Release the lock (1) |
![]() |
Disconnect the connector (2) |
(d) Remove the 3 bolts and airbag ECU assembly. |
![]() |















