Steering Lock Position Signal Circuit Malfunction (B2285). Engine Starter Communication Malfunction (B2779). Open / Short in Steering Lock ECU (B2781)
Steering Lock Position Signal Circuit Malfunction (B2285)
DESCRIPTION
This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2285 |
Steering Lock Position Signal Circuit Malfunction |
The steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*1) |
|
|
- *1: Only detected while a malfunction is present and the power switch is on (IG).
- *2: for Toyota Entune Remote Connect Compatible Type
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The hybrid control system cannot be started. |
The ECU does not send a hybrid control system start request. |
DTC No. | Data List and Active Test |
|---|---|
B2285 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Inspect the fuses of circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or DCM (telematics transceiver)*, refer to Registration.
Click here

- *: for Toyota Entune Remote Connect Compatible Type
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK FOR DTC
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble CodesHINT:
- If the steering cannot be unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.
- If LIN communication is not available, the steering cannot be locked or unlocked.
OK:
LIN communication system DTC B2785 is not output simultaneously.
| NG | GO TO DTC B2785 |
|
READ VALUE USING TECHSTREAM (STEERING UNLOCK SWITCH)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Power Source Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Steering Unlock Switch |
State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) |
OFF or ON |
OFF: Steering locked ON: Steering unlocked |
|
Steering Unlock Switch
OK:
The Techstream display changes.
| OK | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
HINT:
|
|
||||||||||||
Result | Proceed to |
|---|---|
OK (except Toyota Entune Remote Connect Compatible Type) |
A |
OK (for Toyota Entune Remote Connect Compatible Type) |
B |
NG |
C |
| B | GO TO STEP 5 |
| C | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP) - G43-4 (SLP1) |
Always |
Below 1 Ω |
G40-14 (SLP) or G43-4 (SLP1) - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - DCM)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Disconnect the G9 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP) - G43-4 (SLP1) |
Always |
Below 1 Ω |
G43-4 (SLP1) - G9-29 (SLPD) |
Always |
Below 1 Ω |
G40-14 (SLP), G43-4 (SLP1) or G9-29 (SLPD) - Other terminals and body ground |
Always |
10 kΩ or higher |
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP), G43-4 (SLP1) or G9-29 (SLPD) - Body ground |
Always |
Below 1 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Check the push-button start function.
(1) Enter the vehicle while carrying an electrical key transmitter sub-assembly.
(2) Depress the brake pedal with the shift lever in P.
(3) Check that the hybrid control system starts when the power switch is pressed.
Result | Proceed to |
|---|---|
Hybrid control system starts |
A |
Hybrid control system does not start |
B |
| A | REPLACE DCM (TELEMATICS TRANSCEIVER) |
| B | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Engine Starter Communication Malfunction (B2779)
DESCRIPTION
If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered, this DTC is stored.
HINT:
Registration status of the remote engine start ECU ID can be checked using the "Wireless C Code" item in the Data List.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2779 |
Engine Starter Communication Malfunction |
One of the following conditions is met (1 trip detection logic*):
|
|
DTC output confirmation operation:
|
- *: Only output while a malfunction is present.
Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
Hybrid control system does not start with remote start operation |
Hybrid control system cannot be started by remote start operation only |
DTC No. | Data List and Active Test |
|---|---|
B2779 |
Smart Key
|
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- Before performing the inspection, check that DTC B1242 (wireless door lock control system) is not output.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check for CAN communication system DTCs.
Click here ![]()
OK:
CAN communication DTCs are not output.
| NG | GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) |
|
READ VALUE USING TECHSTREAM (WIRELESS C CODE)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Wireless C Code |
Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) |
No Regd or Regd |
No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly) Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
|
Wireless C Code
Result | Proceed to |
|---|---|
"No Regd" is displayed on the Techstream |
A |
"Regd" is displayed on the Techstream |
B |
| B | REPLACE REMOTE ENGINE START ECU |
|
REGISTER REMOTE ENGINE STARTER ID
(a) Register the remote engine starter ID.
|
READ VALUE USING TECHSTREAM (WIRELESS C CODE)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Wireless C Code |
Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) |
No Regd or Regd |
No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly) Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
|
Wireless C Code
Result | Proceed to |
|---|---|
"No Regd" is displayed on the Techstream |
A |
"Regd" is displayed on the Techstream |
B |
| A | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| B | REPLACE REMOTE ENGINE START ECU |
Open / Short in Steering Lock ECU (B2781)
DESCRIPTION
The steering lock ECU and steering lock motor are built into the steering lock actuator or upper bracket assembly.
The steering lock ECU (steering lock actuator or upper bracket assembly) detects whether the steering lock is in the lock or unlock position by using the lock sensor and unlock sensor of the steering lock motor.
The steering lock ECU (steering lock actuator or upper bracket assembly) receives lock and unlock request signals from the certification ECU (smart key ECU assembly) and responds with lock and unlock operation signals.
HINT:
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2781 |
Open / Short in Steering Lock ECU |
One of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the power switch is on (IG).)):
|
|
DTC Output Confirmation Operation:
|
Vehicle Condition and Fail-safe Function when Malfunction Detected Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The steering cannot be locked or unlocked. For this reason, the hybrid control system cannot be started. |
Prohibits the hybrid control system from being started (the hybrid control system does not start). |
DTC No. | Data List and Active Test |
|---|---|
B2781 |
Smart Key
|
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), refer to Registration.
Click here

- After performing repairs, confirm that no DTCs are output again.
Click here

HINT:
When all the ECUs that are connected via LIN communication cannot communicate with the certification ECU (smart key ECU assembly), DTC B2785 is stored.
PROCEDURE
CHECK DTC
(a) Using the Techstream, check if LIN communication DTC B2785 is output.
Body Electrical > Smart Key > Trouble CodesHINT:
If a LIN communication DTC is output, perform troubleshooting for the LIN communication system.
Click here ![]()
Result | Proceed to |
|---|---|
DTC B2785 is output. |
A |
DTC B2785 is not output. |
B |
| A | GO TO LIN COMMUNICATION SYSTEM (DTC B2785) |
| B | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
