System Diagram. Tachometer Malfunction. Terminals Of Ecu
System Diagram
SYSTEM DIAGRAM
HINT:
Refer to System Diagram of CAN Communication System.
Click here ![]()
COMBINATION METER ASSEMBLY DIAGRAM
TURN SIGNAL LIGHT DIAGRAM
(a) LH Side
(b) RH Side
ILLUMINATION DIAGRAM
SPEED SIGNAL DIAGRAM

Tachometer Malfunction
DESCRIPTION
In this circuit, the combination meter assembly receives engine rpm data signal from the hybrid vehicle control ECU via CAN communication. The combination meter assembly displays the engine speed calculated based on the data received from the hybrid vehicle control ECU.
WIRING DIAGRAM
NOTICE:
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
- Before replacing the hybrid vehicle control ECU, refer to Registration.
Click here

PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check if CAN communication DTCs are output.
Click here ![]()
Result | Proceed to |
|---|---|
CAN communication DTCs are not output |
A |
CAN communication DTCs are output |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK FOR DTC (HYBRID CONTROL SYSTEM)
(a) Check if hybrid control system DTCs are output.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
DTCs are output |
B |
| B | GO TO HYBRID CONTROL SYSTEM |
|
READ VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Hybrid Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Powertrain > Hybrid Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Engine Speed |
Engine speed |
- |
Engine stopped: 0 rpm While engine running at a constant speed: No significant fluctuation |
- |
Engine Speed
OK:
Engine speed displayed on the Techstream is almost the same as the tachometer indication.
| OK | USE SIMULATION METHOD TO CHECK |
| NG | REPLACE COMBINATION METER ASSEMBLY |
Terminals Of Ecu
TERMINALS OF ECU
COMBINATION METER ASSEMBLY
(a) Measure the voltage and resistance and check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Signal Input/Output | Condition | Specified Condition |
|---|---|---|---|---|---|
G16-1 (ILL-) - Body ground |
LA-L - Body ground |
Illumination signal |
Output |
Taillights off → Taillights on |
Below 1 V → Pulse generation |
G16-2 (EP) - Body ground |
W-B - Body ground |
Ground |
- |
Always |
Below 1 Ω |
G16-4 (INT) - Body ground |
L - Body ground |
Tire pressure warning ECU and receiver signal |
Output |
|
Below 1.5 V → 8 to 15 V |
G16-5 (SI) - Body ground |
W - Body ground |
Speed signal for other systems (Input) |
Input |
Power switch on (IG), wheel being rotated |
Pulse generation (See waveform 1) |
G16-6 (+S) - Body ground |
L - Body ground |
Speed signal for other systems (Output) |
Output |
Power switch on (IG), wheel being rotated |
Pulse generation (See waveform 1) |
G16-8 (IND) - Body ground |
B - Body ground |
Vehicle proximity notification system warning signal |
Input |
Approximately 3 seconds after turning power switch on (IG) |
Below 1 V |
G16-14 (FR) - G16-33 (FE) |
LG - BE |
Fuel level signal |
Input |
Power switch on (IG), fuel level full → Fuel level low (fuel level warning light on) |
Pulse generation (See waveform 2) |
G16-15 (FV) - Body ground |
GR - Body ground |
Fuel sender gauge (Power source) |
- |
Power switch on (IG) |
Pulse generation (See waveform 3) |
G16-17 (WLVL) - Body ground |
LG - Body ground |
Washer fluid level signal |
Input |
Power switch on (IG), washer fluid level not low → Washer fluid level low |
11 to 14 V → Below 1 V |
G16-18 (RLMT) -Body ground |
BE - Body ground |
Rear seat belt warning light LH signal |
Output |
Power switch on (IG), rear seat belt warning light LH (radio and display receiver assembly) off → Rear seat belt warning light LH (radio and display receiver assembly) on |
11 to 14 V → Below 1 V |
G16-19 (RCMT) -Body ground |
R - Body ground |
Rear seat belt warning light center signal |
Output |
Power switch on (IG), rear seat belt warning light center (radio and display receiver assembly) off → Rear seat belt warning light center (radio and display receiver assembly) on |
11 to 14 V → Below 1 V |
G16-20 (RRMT) -Body ground |
G - Body ground |
Rear seat belt warning light RH signal |
Output |
Power switch on (IG), rear seat belt warning light RH (radio and display receiver assembly) off → Rear seat belt warning light RH (radio and display receiver assembly) on |
11 to 14 V → Below 1 V |
G16-21 (ES) - Body ground |
W-B - Body ground |
Ground |
- |
Always |
Below 1 Ω |
G16-24 (RLSB) - Body ground |
SB - Body ground |
Rear seat belt buckle switch LH signal |
Input |
Power switch on (IG), rear seat belt LH unfastened → Fastened |
Below 1 V → 11 to 14 V |
G16-25 (RCSB) - Body ground |
B - Body ground |
Rear seat belt buckle switch center signal |
Input |
Power switch on (IG), rear seat belt center unfastened → Fastened |
Below 1 V → 11 to 14 V |
G16-26 (RRSB) - Body ground |
LG - Body ground |
Rear seat belt buckle switch RH signal |
Input |
Power switch on (IG), rear seat belt RH unfastened → Fastened |
Below 1 V → 11 to 14 V |
G16-27 (OILW) - Body ground |
W - Body ground |
Engine oil level signal |
Input |
Power switch on (IG), engine oil level not low → Engine oil level low |
Below 1 V → 11 to 14 V |
G16-28 (MSM+) - Body ground |
GR - Body ground |
Steering pad switch assembly signal |
Input |
Power switch on (IG), up, down, right and left switches on steering pad switch assembly not pushed |
4.8 to 5.2 V |
G16-29 (MSTI) - Body ground |
R - Body ground |
Steering pad switch assembly signal |
Input |
Power switch on (IG), OK and back switches on steering pad switch assembly not pushed |
4.8 to 5.2 V |
G16-31 (CANL) |
W |
CAN communication line |
Input/Output |
- |
- |
G16-32 (CANH) |
B |
CAN communication line |
Input/Output |
- |
- |
G16-34 (LST1) - Body ground |
L - Body ground |
Fuel lid operation signal |
Input |
"Ready to Refuel" displayed on multi-information display |
Pulse generation (See waveform 4) |
"Close Fuel Lid" displayed on multi-information display |
Pulse generation (See waveform 5) |
||||
Power switch on (IG) |
11 to 14 V |
||||
G16-36 (TX+) |
G |
Local bus communication line |
Input/Output |
- |
- |
G16-37 (TX-) |
W |
Local bus communication line |
Input/Output |
- |
- |
G16-39 (IG+) - Body ground |
GR - Body ground |
Power switch signal |
- |
Power switch off → Power switch on (IG) |
Below 1 V → 11 to 14 V |
G16-40 (B) - Body ground |
LA-B - Body ground |
Auxiliary battery |
- |
Power switch off |
11 to 14 V |
G15-1 (ODO) - Body ground |
LA-L - Body ground |
ODO/TRIP switch signal |
Input |
Power switch on (IG), ODO/TRIP switch (trip switch) not pushed |
4.8 to 5.2 V |
G15-2 (TR) - Body ground |
L - Body ground |
Light control rheostat switch signal |
Input |
Power switch on (IG), light control rheostat up switch (trip switch) and light control rheostat down switch (trip switch) not pushed |
4.8 to 5.2 V |
G15-3 (HAZ) - Body ground |
LA-R - Body ground |
Hazard warning switch signal |
Input |
Hazard warning switch assembly (radio and display receiver assembly) off → Hazard warning switch assembly (radio and display receiver assembly) pushed |
11 to 14 V → Below 1 V |
G15-5 (SW3) - Body ground |
LA-B - Body ground |
Ground for trip switch |
- |
Always |
Below 1 Ω |
G15-7 (LR) - Body ground |
LA-G - Body ground |
Front turn signal light RH signal |
Output |
Power switch on (IG), RH turn indicator light off → RH turn indicator light blinking |
Below 1 V → 11 to 14 V ←→ Below 1 V |
G15-8 (B) - Body ground |
LA-B - Body ground |
Auxiliary battery |
- |
Power switch off |
11 to 14 V |
G15-10 (TRNL) - Body ground |
BE - Body ground |
Rear turn signal light LH signal |
Output |
Power switch on (IG), LH turn indicator light off → LH turn indicator light blinking |
Below 1 V → 11 to 14 V ←→ Below 1 V |
G15-11 (LL) - Body ground |
LA-LG - Body ground |
Front turn signal light LH signal |
Output |
Power switch on (IG), LH turn indicator light off → LH turn indicator light blinking |
Below 1 V → 11 to 14 V ←→ Below 1 V |
G15-13 (TRNR) - Body ground |
BE - Body ground |
Rear turn signal light RH signal |
Output |
Power switch on (IG), RH turn indicator light off → RH turn indicator light blinking |
Below 1 V → 11 to 14 V ←→ Below 1 V |
- Waveform 1:
Item
Condition
Tester connection
- G16-5 (SI) - Body ground
- G16-6 (+S) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Condition
Power switch on (IG), wheel being rotated
HINT:
When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.
- Waveform 2:
Item
Condition
Tester connection
G16-14 (FR) - G16-33 (FE)
Tool setting
2.5 V/DIV., 20 ms./DIV.
Condition
Power switch on (IG), fuel level full → low (fuel level warning light on)
HINT:
- (A) will depending on the fuel level.
- Power switch on (IG), fuel level full → Fuel level low (fuel level warning light on) (4.2 to 4.6 → 0.3 to 1.2 V)
- Waveform 3:
Item
Condition
Tester connection
G16-15 (FV) - Body ground
Tool setting
2.5 V/DIV., 20 ms./DIV.
Condition
Power switch on (IG)
HINT:
Power switch on (IG) (4.5 to 5.5 V)
- Waveform 4:
Item
Condition
Tester Connection
G16-34 (LST1) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Condition
"Ready to Refuel" displayed on multi-information display

- Waveform 5:
Item
Condition
Tester Connection
G16-34 (LST1) - Body ground
Tool setting
5 V/DIV., 20 ms./DIV.
Condition
"Close Fuel Lid" displayed on multi-information display
HINT:
This waveform is output when the fuel lid opener switch is operated if the fuel lid is open and any of the following conditions are met:
- The vehicle has been driven for 1 km (0.6 mile) or more at a speed of 50 km/h or more.
- 30 minutes or more have elapsed since the fuel lid opener switch was operated.