Engine Immobiliser System Circuit Short to Battery (B279A12). Engine Immobiliser System Incorrect Assembly (B279C95). Ignition Hold Monitor Malfunction (B2271)
Engine Immobiliser System Circuit Short to Battery (B279A12)
DESCRIPTION
If the communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high, the ECM will store this DTC.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B279A12 |
Engine Immobiliser System Circuit Short to Battery |
The communication line (IMI - EFIO) between the ECM and certification ECU (smart key ECU assembly) is stuck high. (1 trip detection logic*) |
|
DTC output confirmation operation:
|
- *: Only output while a malfunction is present.
Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
Engine cannot be started |
Engine cannot be started |
DTC No. | Data List and Active Test |
|---|---|
B279A12 |
- |
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here
- Before replacing the ECM or certification ECU (smart key ECU assembly), refer to Registration.
Click here
- After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
When DTC B279A12 and a certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the certification ECU (smart key ECU assembly) DTC.
PROCEDURE
CHECK CONNECTION OF CONNECTOR
(a) Turn the engine switch off.
(b) Check that the connectors are properly connected to the ECM and certification ECU (smart key ECU assembly).
OK:
Connectors are properly connected.
| NG | CONNECT CONNECTORS PROPERLY |
|
CHECK WHETHER ENGINE STARTS
(a) Check that the engine starts.
OK:
Engine starts normally.
| OK | USE SIMULATION METHOD TO CHECK |
|
CHECK ECM
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| NG | GO TO STEP 5 |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (TERMINAL EFIO)
(a) Connect the A10 certification ECU (smart key ECU assembly) connector.
(b) Using an oscilloscope, check the waveform.
*a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
*b |
Waveform |
*c |
Approximately 160 ms. |
*d |
Approximately 270 ms. |
OK:
Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
A10-4 (EFIO) - Body ground |
Engine switch turned on (IG) using registered electrical key transmitter sub-assembly |
2 V/DIV., 500 ms./DIV. |
Pulse generation (See waveform) |
| OK | REPLACE ECM |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
(a) Disconnect the A18 ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A10-4 (EFIO) - A18-59 (IMI) |
Always |
Below 1 Ω |
| OK | REPLACE ECM |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Engine Immobiliser System Incorrect Assembly (B279C95)
DESCRIPTION
If an ECM that is incompatible with the immobiliser function is installed, the ECM will store this DTC.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B279C95 |
Engine Immobiliser System Incorrect Assembly |
An ECM that is incompatible with the immobiliser function is installed. (1-trip detection logic*) |
ECM |
- |
- *: Only detected while a malfunction is present.
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
Engine cannot be started |
- |
DTC No. | Data List and Active Test |
|---|---|
B279C95 |
- |
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the ECM, refer to Registration.
Click here

- After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
REPLACE ECM
(a) Temporarily replace the ECM with a new one.
Click here ![]()
| NEXT | END (ECM WAS DEFECTIVE) |
Ignition Hold Monitor Malfunction (B2271)
DESCRIPTION
This DTC is stored when a malfunction in the IG circuit or IG hold circuit of the certification ECU (smart key ECU assembly) is detected.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2271 |
Ignition Hold Monitor Malfunction |
When either of the following conditions is met (1-trip detection logic*1):
|
|
|
- *1: Only detected while a malfunction is present and the engine switch is on (IG).
- *2: The IG circuit and IG hold circuit activate the IG relay.
- *3: After the IG circuit turns on, even if the certification ECU (smart key ECU assembly) malfunctions, the IG hold circuit will maintain the power source mode in on (IG).
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The engine switch cannot be turned on (IG) (the engine cannot be started). |
The power source mode cannot be changed to on (IG). |
DTC No. | Data List and Active Test |
|---|---|
B2271 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | END (TEMPORARY CONNECTION FAILURE IS SUSPECTED) |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
