Pre-collision System(for Hv Model)
Front Radar Sensor Region Code Mismatch (C1A0A)
DESCRIPTION
The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.
Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly calculates the possibility of a collision and operates the pre-collision system if it determines that the possibility is high.
When the millimeter wave radar sensor assembly is replaced with a new one, it acquires the country specification information from the driving support ECU assembly. Also, when the driving support ECU assembly is replaced with a new one, it receives country specification information from the main body ECU (multiplex network body ECU). If country specification information in the millimeter wave radar sensor assembly, driving support ECU and/or main body ECU do not match, DTC C1A0A will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A0A |
Front Radar Sensor Region Code Mismatch |
When the power switch is on (IG), the country specification information in the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds. |
|
NOTICE:
- When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

- The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC C1A0A is not output |
A |
DTC C1A0A is output |
B |
| A | USE SIMULATION METHOD TO CHECK |
|
REPLACE DRIVING SUPPORT ECU ASSEMBLY
(a) Replace the driving support ECU assembly.
Click here ![]()
|
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC C1A0A is not output |
A |
DTC C1A0A is output |
B |
| A | END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE) |
|
REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Replace the millimeter wave radar sensor assembly.
Click here ![]()
(b) Adjust the millimeter wave radar sensor assembly.
Click here ![]()
| NEXT | END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE) |
Driving Support ECU (C1A01)
DESCRIPTION
The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.
Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly calculates the possibility of a collision and operates the pre-collision system if it determines that the possibility is high.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A01 |
Driving Support ECU |
When the power switch is on (IG), the driving support ECU assembly detects an internal malfunction for approximately 1 second. |
Driving support ECU assembly |
NOTICE:
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
PROCEDURE
REPLACE DRIVING SUPPORT ECU ASSEMBLY
(a) Replace the driving support ECU assembly.
Click here ![]()
| NEXT | END |
Vehicle Information Not Obtained (C1A02)
DESCRIPTION
When a new driving support ECU assembly is installed, it receives vehicle specification information (destination, steering wheel position, etc.) from the main body ECU (multiplex network body ECU) and stores the information.
DTC C1A02 is stored when the driving support ECU assembly receives the vehicle specification information from the main body ECU (multiplex network body ECU) but cannot store it.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A02 |
Vehicle Information Not Obtained |
The vehicle specification information of the main body ECU (multiplex network body ECU) and driving support ECU assembly do not match for 1 second or more while the vehicle is being driven at a speed of 50 km/h or more. |
Driving support ECU assembly |
NOTICE:
- When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE
REPLACE DRIVING SUPPORT ECU ASSEMBLY
(a) Replace the driving support ECU assembly.
Click here ![]()
| NEXT | END |
Stop Light Relay Circuit (C1A4B)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) sends a stop light operation request signal to the stop light relay (stop light switch assembly). If the skid control ECU (brake booster with master cylinder assembly) detects a malfunction in the stop light relay (stop light switch assembly) circuit, the driving support ECU assembly stores DTC C1A4B.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A4B |
Stop Light Relay Circuit |
Both of the following conditions are met:
|
Electronically controlled brake system |
NOTICE:
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
PROCEDURE
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM
HINT:
If DTC C1A4B is output by the pre-collision system, perform troubleshooting for the electronically controlled brake system.
Click here ![]()
| NEXT | END |
Front Radar Sensor (C1A10)
DESCRIPTION
The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle.
Based on this signals from the millimeter wave radar sensor assembly, the driving support ECU assembly sends pre-collision system control operation signals.
If the driving support ECU assembly receives an internal malfunction signal from the millimeter wave radar sensor assembly, it stores DTC C1A10.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A10 |
Front Radar Sensor |
When the power switch is on (IG), the driving support ECU assembly receives an internal malfunction signal from the millimeter wave radar sensor assembly for approximately 0.2 seconds. |
Millimeter wave radar sensor assembly |
NOTICE:
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

- The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE
REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Replace the millimeter wave radar sensor assembly.
Click here ![]()
(b) Adjust the millimeter wave radar sensor assembly.
Click here ![]()
| NEXT | END |
Front Radar Sensor Incorrect Axial Gap (C1A11,C1A14)
DESCRIPTION
The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.
Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly sends pre-collision system control operation signals.
When the vehicle is determined to be driving in a straight line or on a gradual curve based on signals from the yaw rate sensor, etc., the millimeter wave radar sensor assembly performs self diagnosis to check if the sensor beam axis has deviated. If the millimeter wave radar sensor assembly beam axis has deviated, the driving support ECU assembly detects this and stores DTC C1A11.
After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment has not been performed, DTC C1A14 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A11 |
Front Radar Sensor Incorrect Axial Gap |
When the power switch is on (IG), misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds. |
Millimeter wave radar sensor assembly |
C1A14 |
Front Radar Sensor Beam Axis Not Adjusted |
When the vehicle is being driven at a speed of 10 km/h or more, incompletion of the millimeter wave radar sensor assembly beam axis alignment is detected for approximately 0.2 seconds. |
Millimeter wave radar sensor assembly |
NOTICE:
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

PROCEDURE
ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Perform millimeter wave radar sensor assembly adjustment.
Click here ![]()
|
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC C1A11 and C1A14 are not output |
A |
DTC C1A11 or C1A14 is output |
B |
| A | END |
| B | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Yaw Rate Sensor (C1A46)
DESCRIPTION
The driving support ECU assembly receives yaw rate sensor signals from the airbag ECU assembly and skid control ECU (brake booster with master cylinder assembly) via CAN communication. If the driving support ECU assembly receives a yaw rate sensor malfunction signal from the airbag ECU assembly or skid control ECU (brake booster with master cylinder assembly), DTC C1A46 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A46 |
Yaw Rate Sensor |
|
Electronically controlled brake system |
Vehicle Condition |
|||
|---|---|---|---|
Pattern 1 | Pattern 2 |
||
Malfunction Status |
Vehicle is being driven at a speed of 5 km/h or more |
○ |
○ |
Driving support ECU assembly receives a yaw rate sensor malfunction signal from airbag ECU assembly |
○ |
- |
|
Driving support ECU assembly receives a yaw rate sensor zero point malfunction signal from skid control ECU (brake booster with master cylinder assembly) |
- |
○ |
|
Detection Time |
Approximately 10 seconds or more |
Approximately 10 seconds or more |
|
Number of Trips |
1 trip |
1 trip |
|
HINT:
DTC will be stored when the conditions of any pattern in the table above are met.
NOTICE:
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
PROCEDURE
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM
HINT:
If DTC C1A46 is output by the pre-collision system, perform troubleshooting for the electronically controlled brake system.
Click here ![]()
| NEXT | END |
Steering Angle Sensor (C1A47)
DESCRIPTION
The driving support ECU assembly receives steering angle information from the steering sensor. If the driving support ECU assembly detects a steering sensor malfunction, DTC C1A47 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A47 |
Steering Angle Sensor |
While the vehicle is being driven at a speed of 50 km/h or more, the driving support ECU assembly receives a steering sensor malfunction signal continuously for 1 second or more. |
Electronically controlled brake system |
NOTICE:
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
PROCEDURE
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM
HINT:
If DTC C1A47 is output by the pre-collision system, perform troubleshooting for the electronically controlled brake system.
Click here ![]()
| NEXT | END |
Brake System Malfunction (C1A50)
DESCRIPTION
When the pre-collision system is operating, the driving support ECU assembly sends brake control signals to the skid control ECU (brake booster with master cylinder assembly).
If the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication, DTC C1A50 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A50 |
Brake System Malfunction |
While the power switch is on (IG), the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) for 0.3 seconds or more. |
Electronically controlled brake system |
NOTICE:
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
PROCEDURE
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM
HINT:
If DTC C1A50 is output by the pre-collision system, perform troubleshooting for the electronically controlled brake system.
Click here ![]()
| NEXT | END |
Other System Malfunction (C1A63)
DESCRIPTION
If the hybrid vehicle control ECU detects a malfunction in the hybrid control system, it outputs a malfunction signal to the driving support ECU assembly via CAN communication and this DTC is stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A63 |
Other System Malfunction |
With the power switch on (IG), the driving support ECU assembly receives a hybrid system malfunction signal from the hybrid vehicle control ECU for approximately 2 seconds or more. |
Hybrid control system |
PROCEDURE
GO TO HYBRID CONTROL SYSTEM
HINT:
If DTC C1A63 is output by the pre-collision system, perform troubleshooting for the hybrid control system.
Click here ![]()
| NEXT | END |
Brake Control Signal Mismatch (C1A64)
DESCRIPTION
The skid control ECU (brake booster with master cylinder assembly) sends signals to the driving support ECU assembly according to the brake control status. If the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly), it will store DTC C1A64.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1A64 |
Brake Control Signal Mismatch |
While the power switch is on (IG), the driving support ECU assembly receives an electronically controlled brake system malfunction signal from the skid control ECU (brake booster with master cylinder assembly) continuously for 0.5 seconds or more. |
Electronically controlled brake system |
NOTICE:
The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
PROCEDURE
GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM
HINT:
If DTC C1A64 is output by the pre-collision system, perform troubleshooting for the electronically controlled brake system.
Click here ![]()
| NEXT | END |
Front Camera Module Circuit (C1AA0)
DESCRIPTION
The driving support ECU assembly receives information about the area in front of the vehicle from the forward recognition camera.
If the driving support ECU assembly detects a malfunction in the forward recognition camera, it will store DTC C1AA0.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1AA0 |
Front Camera Module Circuit |
While the power switch is on (IG), the forward recognition camera detects an internal malfunction for approximately 0.3 seconds or more. |
Forward recognition camera |
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
- If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click here

- The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here

PROCEDURE
REPLACE FORWARD RECOGNITION CAMERA
(a) Replace the forward recognition camera.
Click here ![]()
(b) Perform forward recognition camera adjustment.
Click here ![]()
| NEXT | END |
Front Camera Module Beam Axis Not Adjusted (C1AA9)
DESCRIPTION
If forward recognition camera adjustment has not been performed or did not complete normally after the forward recognition camera was replaced with a new one, DTC C1AA9 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1AA9 |
Front Camera Module Beam Axis Not Adjusted |
When the pre-collision system is on, the driving support ECU assembly detects that forward recognition camera adjustment has not been completed for 0.3 seconds or more. |
Front camera system |
PROCEDURE
GO TO FRONT CAMERA SYSTEM
HINT:
If DTC C1AA9 is output by the pre-collision system, perform troubleshooting for the front camera system.
Click here ![]()
| NEXT | END |
Heater Circuit (C1AAE)
DESCRIPTION
If the forward recognition camera detects a malfunction in the forward recognition with heater hood sub-assembly circuit, it will output a malfunction signal to the driving support ECU assembly via CAN communication and this DTC will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
C1AAE |
Heater Circuit |
When the power switch is on (IG), the driving support ECU assembly receives a forward recognition with heater hood sub-assembly malfunction signal from the forward recognition camera continuously for 1 second or more. |
Front camera system |
PROCEDURE
GO TO FRONT CAMERA SYSTEM
HINT:
If DTC C1AAE is output by the pre-collision system, perform troubleshooting for the front camera system.
Click here ![]()
| NEXT | END |
Customize Parameters
CUSTOMIZE PARAMETERS
NOTICE:
- When the customer requests a change in a function, first make sure that the function can be customized.
- Make a note of the current settings before customizing.
HINT:
The following PCS functions and the pre-collision system sensitivity setting can be changed from their default setting.
CUSTOMIZE PRE-COLLISION SYSTEM
(a) Customizing with the Techstream
(1) Turn the power switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Enter the following menus: Customize Setting / Others.
(6) Select the setting by referring to the table below.
OthersTester Display | Description | Default | Setting | ECU |
|---|---|---|---|---|
PCS Operation State Retention Setting |
Refer to the table below |
OFF |
0:OFF,1:ON |
Driving support ECU assembly |
PCS Alarm Activation Distance Retention Setting 1 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Driving support ECU assembly |
PCS Alarm Activation Distance Retention Setting 2 |
Refer to the table below |
ON |
0:OFF,1:ON |
Driving support ECU assembly |
PCS Alarm Activation Distance Retention Setting 3 |
Refer to the table below |
OFF |
0:OFF,1:ON |
Driving support ECU assembly |
Customize Setting | Description | Setting |
|---|---|---|
PCS Operation State Retention Setting |
Function to maintain the pre-collision system on/off setting when the power switch is turned off and then on (IG). |
OFF: Not maintained (Pre-collision system always turns on) ON: Maintained |
PCS Alarm Activation Distance Retention Setting 1 |
Function to maintain the sensitivity setting of the pre-collision system when the pre-collision system is turned off and then on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
PCS Alarm Activation Distance Retention Setting 2 |
Function to maintain the sensitivity setting of the pre-collision system when the power switch is turned off while the pre-collision system is on. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
PCS Alarm Activation Distance Retention Setting 3 |
Function to maintain the sensitivity setting of the pre-collision system when the power switch is turned off while the pre-collision system is off. |
OFF: Not maintained (Setting changes to "Mid") ON: Maintained |
Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Turn Light RH |
Turn signal switch (right) status |
ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
Turn Light LH |
Turn signal switch (left) status |
ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
PCS OFF Switch |
Pre-collision system on/off status |
ON or OFF |
ON: Pre-collision system on OFF: Pre-collision system off |
- |
Pre-Collision Safety Warning Buz |
Pre-collision system warning buzzer |
Valid or Inval |
Valid: Pre-collision system warning buzzer operation possible Inval: Pre-collision system warning buzzer operation not possible |
- |
Pre-Collision Brake |
Pre-collision braking function |
Valid or Inval |
Valid: Pre-collision braking operation possible Inval: Pre-collision braking operation not possible |
- |
PBA Start |
Pre-collision brake assist activation signal |
OFF, Standby, Assist Lv1 or Assist Lv2 |
OFF: Pre-collision brake assist not operating Standby: Brake pedal not depressed during pre-collision brake assist operation Assist Lv1: Brake pedal depressed during pre-collision brake assist operation Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation |
Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal) |
Warning Brake |
- |
- |
- |
Not applicable to the vehicle |
Brake Assist Standby |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
Pre-Collision Brake Control |
Pre-collision braking operational status |
ON or OFF |
ON: Pre-collision braking operating OFF: Pre-collision braking not operating |
- |
AVS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
VGRS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
PBA Control |
Pre-collision brake assist operational status |
Valid or Invalid |
Valid: Pre-collision brake assist control operation possible Invalid: Pre-collision brake assist control operation not possible |
- |
Pre-Collision Safety Brake Ind |
Pre-collision system alarm warning message status |
ON or OFF |
ON: Displayed OFF: Not displayed |
"BRAKE!" is displayed |
PCS Crash Alarm Buzzer |
PCS meter buzzer status |
ON or OFF |
ON: PCS meter buzzer sounding OFF: PCS meter buzzer not sounding |
- |
Front Radar-Dirt History |
Millimeter wave radar sensor assembly dirt history |
ON or OFF |
ON: History of excessive dirt OFF: No history of excessive dirt |
- |
Front Radar-Temperature Malfunction History |
Millimeter wave radar sensor assembly abnormal temperature history |
ON or OFF |
ON: History of abnormal temperature OFF: No history of abnormal temperature |
- |
Front Radar-Low Voltage History |
Millimeter wave radar sensor assembly low voltage history |
ON or OFF |
ON: History of low voltage OFF: No history of low voltage |
- |
Front Radar-Incorrect Axial Gap (Vertical) History |
Millimeter wave radar sensor assembly vertical misalignment history |
ON or OFF |
ON: History of vertical misalignment OFF: No history of vertical misalignment |
If "Pre-Collision System Unavailable." is displayed on the multi-information display and there is front beam axis misalignment (vertical) history, the millimeter wave radar sensor assembly may be performing beam axis alignment correction. In this case, perform Front Beam Axis Adjustment to return the system to normal. |
Front Radar-Incorrect Axial Gap (Horizontal) History |
Millimeter wave radar sensor assembly horizontal misalignment history |
ON or OFF |
ON: History of horizontal misalignment OFF: No history of horizontal misalignment |
- |
Front Recognition Camera-Blockage History |
Forward recognition camera obstruction history |
ON or OFF |
ON: History of being obstructed OFF: No history of being obstructed |
- |
Front Recognition Camera-Malfunction History |
Front camera system unavailable history |
ON or OFF |
ON: History of unavailable OFF: No history of unavailable |
- |
Driving Support ECU Destination Variation No |
Destination country for driving support computer |
Destination Variation No or Not Available |
Actual country code |
- |
Control Mode |
ECU control mode status |
Normal or Check Mode |
Normal: Normal operation Check Mode: Operating in Control Mode |
- |
PCS Operation State Retention Setting |
PCS Operation State Retention Setting customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 1 |
PCS Alarm Activation Distance Retention Setting 1 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 2 |
PCS Alarm Activation Distance Retention Setting 2 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 3 |
PCS Alarm Activation Distance Retention Setting 3 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
The Number of DTCs |
Number of trouble codes |
0 to 255 |
Number of DTCs will be displayed |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
PCS Crash Alarm Buzzer |
PCS meter buzzer |
ON / OFF |
Test possible with power switch on (IG), vehicle stopped |
Diagnosis System
DIAGNOSIS SYSTEM
CHECK DLC3
(a) Check the DLC3.
Click here ![]()
FUNCTION OF WARNING INDICATOR AND MESSAGE
(a) If the pre-collision system is not functioning properly, the driver is warned by the PCS warning light and a warning message displayed on the multi-information display.
Master Warning Indicator | Warning Message | Detail | DTC | PCS warning light |
|---|---|---|---|---|
Illuminated |
"Pre-Collision System Malfunction Visit Your Dealer" is displayed |
Pre-collision system malfunctioning |
Stored |
Illuminates |
Not illuminated |
"Pre-Collision System Unavailable" |
|
Not stored |
Illuminates |
Not illuminated |
"Pre-Collision System Unavailable Clean Sensor" |
Foreign matter attached to millimeter wave radar sensor assembly |
Not stored |
Illuminates |
Not illuminated |
"Front Camera Unavailable" |
|
Not stored |
Illuminates |
Not illuminated |
"Front Camera Unavailable Remove Debris On Windshield" |
Front of forward recognition camera or windshield glass is dirty or misty |
Not stored |
Illuminates |
Not illuminated |
"VSC Turned Off Pre-Collision Brake System Unavailable" |
VSC system is disabled |
Not stored |
Illuminates |
PCS Warning Light | Condition |
|---|---|
Illuminates |
Pre-collision system malfunctioning (DTC stored) |
Pre-collision system temporarily disabled |
|
Pre-collision system disabled |
|
VSC system disabled |
|
Not illuminated |
Other |
INITIAL CHECK
(a) An initial check is performed when the power switch is off for more than 2 seconds and then turned on (IG). The initial check consists of a pre-collision system diagnostic check with a duration of approximately 3 seconds.
(b) If a malfunction is detected during the initial check, the PCS warning light in the combination meter assembly will illuminate and a warning message indicating the pre-collision system is malfunctioning or disabled will be displayed on the multi-information display.
CONSTANT CHECK
(a) The driving support ECU assembly constantly monitors the pre-collision system for malfunctions after the power switch is turned on (IG) and the initial check (approximately 3 seconds) has completed.
(b) If a malfunction is detected during the constant check, the PCS warning light in the combination meter assembly will illuminate and a warning message indicating the pre-collision system is malfunctioning or disabled will be displayed on the multi-information display.
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Pre-collision SystemDTC No. | Detection Item | Link |
|---|---|---|
C1A01 |
Driving Support ECU |
|
C1A02 |
Vehicle Information Not Obtained |
|
C1A0A |
Front Radar Sensor Region Code Mismatch |
|
C1A10 |
Front Radar Sensor |
|
C1A11 |
Front Radar Sensor Incorrect Axial Gap |
|
C1A14 |
Front Radar Sensor Beam Axis Not Adjusted |
|
C1A46 |
Yaw Rate Sensor |
|
C1A47 |
Steering Angle Sensor |
|
C1A4B |
Stop Light Relay Circuit |
|
C1A50 |
Brake System Malfunction |
|
C1A63 |
Other System Malfunction |
|
C1A64 |
Brake Control Signal Mismatch |
|
C1AA0 |
Front Camera Module Circuit |
|
C1AA9 |
Front Camera Module Beam Axis Not Adjusted |
|
C1AAE |
Heater Circuit |
|
U0125 |
Lost Communication with Yaw Rate Sensor Module |
|
U0126 |
Lost Communication with Steering Angle Sensor Module |
|
U0129 |
Lost Communication with Brake System Control Module |
|
U0155 |
Lost Communication with Instrument Panel Cluster (IPC) Control Module |
|
U0235 |
Lost Communication with Cruise Control Front Distance Range Sensor |
|
U023A |
Lost Communication with Front Camera Module |
|
U0293 |
Lost Communication with HV ECU |
|
U1002 |
Lost Communication with Gateway Module |
|
U1104 |
Lost Communication with Driving Support ECU |
Dtc Check / Clear
DTC CHECK / CLEAR
CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.
(e) Check for DTCs.
Click here ![]()
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Clear DTCs.
(e) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCsFail-safe Chart
FAIL-SAFE CHART
FAIL-SAFE FUNCTION
(a) When a malfunction occurs in the pre-collision system, a message will be displayed on the multi-information display and the pre-collision system will be disabled depending on the malfunction.
Warning Message | Cause | DTC No. | Conditions to Return to Normal |
|---|---|---|---|
"Pre-Collision System Malfunction Visit Your Dealer" is displayed |
Pre-collision system malfunction |
C1A01 |
After system returns to normal, power switch is turned off and then on (IG) |
C1A02 |
System returns to normal |
||
C1A0A |
System returns to normal |
||
C1A10 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1A11 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1A14 |
System returns to normal |
||
C1A46 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1A47 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1A4B |
System returns to normal |
||
C1A50 |
System returns to normal |
||
C1A63 |
System returns to normal |
||
C1A64 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1AA0 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1AA9 |
After system returns to normal, power switch is turned off and then on (IG) |
||
C1AAE |
After system returns to normal, power switch is turned off and then on (IG) |
||
U0125 |
System returns to normal |
||
U0126 |
System returns to normal |
||
U0129 |
System returns to normal |
||
U0155 |
System returns to normal |
||
U0235 |
System returns to normal |
||
U023A |
System returns to normal |
||
U0293 |
System returns to normal |
||
U1002 |
System returns to normal |
||
U1104 |
System returns to normal |
||
"Pre-Collision System Unavailable" |
|
|
|
"Pre-Collision System Unavailable Clean Sensor" |
Foreign matter attached to millimeter wave radar sensor assembly |
Millimeter wave radar sensor assembly is cleaned |
|
"Front Camera Unavailable" |
Forward recognition camera temporarily malfunctioning
|
|
|
"Front Camera Unavailable Remove Debris On Windshield" |
Front of forward recognition camera or windshield glass is dirty or misty |
Forward recognition camera or area of windshield glass in front of forward recognition camera is cleaned |
|
Freeze Frame Data
FREEZE FRAME DATA
DESCRIPTION
(a) When a pre-collision system DTC is stored, the driving support ECU assembly stores the current vehicle (ECU or sensor) state as Freeze Frame Data.
CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Pre-Collision 2 / Trouble Codes.
Body Electrical > Pre-Collision 2 > Trouble Codes(e) According to the Techstream display, select a DTC that stored freeze frame data.
(f) Read the freeze frame data recorded when the DTC was stored.
Body Electrical > Pre-Collision 2Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Turn Light RH |
Turn signal switch (right) status |
ON or OFF |
ON: Turn signal switch (right) on OFF: Turn signal switch (right) off |
- |
Turn Light LH |
Turn signal switch (left) status |
ON or OFF |
ON: Turn signal switch (left) on OFF: Turn signal switch (left) off |
- |
PCS OFF Switch |
Pre-collision system on/off status |
ON or OFF |
ON: Pre-collision system on OFF: Pre-collision system off |
- |
Pre-Collision Safety Warning Buz |
Pre-collision system warning buzzer |
Valid or Inval |
Valid: Pre-collision system warning buzzer operation possible Inval: Pre-collision system warning buzzer operation not possible |
- |
Pre-Collision Brake |
Pre-collision braking function |
Valid or Inval |
Valid: Pre-collision braking operation possible Inval: Pre-collision braking operation not possible |
- |
PBA Start |
Pre-collision brake assist activation signal |
OFF, Standby, Assist Lv1 or Assist Lv2 |
OFF: Pre-collision brake assist not operating Standby: Brake pedal not depressed during pre-collision brake assist operation Assist Lv1: Brake pedal depressed during pre-collision brake assist operation Assist Lv2: Brake pedal firmly depressed during pre-collision brake assist operation |
Signal status changes when the pre-collision brake assist is activated before a crash (Pre-collision brake will activate only in situations where the driver depresses the brake pedal) |
Warning Brake |
- |
- |
- |
Not applicable to the vehicle |
Brake Assist Standby |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
Pre-Collision Brake Control |
Pre-collision braking operational status |
ON or OFF |
ON: Pre-collision braking operating OFF: Pre-collision braking not operating |
- |
AVS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
VGRS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
PBA Control |
Pre-collision brake assist operational status |
Valid or Invalid |
Valid: Pre-collision brake assist control operation possible Invalid: Pre-collision brake assist control operation not possible |
- |
Pre-Collision Safety Brake Ind |
Pre-collision system alarm warning message status |
ON or OFF |
ON: Displayed OFF: Not displayed |
"BRAKE!" is displayed |
PCS Crash Alarm Buzzer |
PCS meter buzzer status |
ON or OFF |
ON: PCS meter buzzer sounding OFF: PCS meter buzzer not sounding |
- |
Front Radar-Low Voltage History |
Millimeter wave radar sensor assembly low voltage history |
ON or OFF |
ON: History of low voltage OFF: No history of low voltage |
- |
Front Radar-Incorrect Axial Gap (Vertical) History |
Millimeter wave radar sensor assembly vertical misalignment history |
ON or OFF |
ON: History of vertical misalignment OFF: No history of vertical misalignment |
- |
Front Radar-Incorrect Axial Gap (Horizontal) History |
Millimeter wave radar sensor assembly horizontal misalignment history |
ON or OFF |
ON: History of horizontal misalignment OFF: No history of horizontal misalignment |
- |
Front Recognition Camera-Malfunction History |
Front camera system unavailable history |
ON or OFF |
ON: History of unavailable OFF: No history of unavailable |
- |
Control Mode |
ECU control mode status |
Normal or Check Mode |
Normal: Normal operation Check Mode: Operating in Control Mode |
- |
PCS Operation State Retention Setting |
PCS Operation State Retention Setting customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 1 |
PCS Alarm Activation Distance Retention Setting 1 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 2 |
PCS Alarm Activation Distance Retention Setting 2 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
PCS Alarm Activation Distance Retention Setting 3 |
PCS Alarm Activation Distance Retention Setting 3 customize setting |
ON or OFF |
ON: Customize setting set to ON OFF: Customize setting set to OFF |
- |
How To Proceed With Troubleshooting
HINT:
- Use these procedures to troubleshoot the pre-collision system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
INSPECT AUXILIARY BATTERY VOLTAGE
(a) Measure the auxiliary battery voltage with the power switch off.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.
|
INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (BEAM AXIS MISALIGNMENT READING)*
(a) Adjust the reflector height.
Click here ![]()
(b) Place the reflector.
Click here ![]()
(c) Connect the Techstream to the DLC3.
(d) Turn the power switch on (IG).
(e) Turn the Techstream on.
(f) Turn the cruise control main switch on.
(g) Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Misalignment Reading.
(h) Check the amount of misalignment and make a note.
Body Electrical > Pre-Collision 2 > UtilityFront Beam Axis Misalignment Reading
(i) Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Front Beam Axis Offset Reading.
(j) Check the amount of misalignment and make a note.
Body Electrical > Pre-Collision 2 > UtilityFront Beam Axis Offset Reading
(k) Calculate the "Dealership Axis Offset Angle (with On-line Calibration Angle)" using the values "Front Beam Axis Misalignment Reading" and "Front Beam Axis Offset Reading".
(1) "Dealership Axis Offset Angle (with On-line Calibration Angle)" = "Front Beam Axis Misalignment Reading" - "Front Beam Axis Offset Reading"
Standard:
Dealership Axis Offset Angle (with On-line Calibration Angle)
Vertical |
-2.2 to 1.6 deg. |
Horizontal |
-0.6 to 0.6 deg. |
Result | Proceed to |
|---|---|
The dealership axis offset angle (with on-line calibration angle) is within the specified range. |
A |
The dealership axis offset angle (with on-line calibration angle) is not within the specified range. |
B |
| B | GO TO STEP 12 |
|
CHECK CAN COMMUNICATION SYSTEM*
(a) Using the Techstream, check if the CAN communication system is functioning normally.
HINT:
Refer to CAN Bus Check in CAN Communication System.
Click here ![]()
OK:
CAN communication system is functioning normally.
| NG | GO TO CAN COMMUNICATION SYSTEM |
|
INSPECT WARNING LIGHT
(a) Check the condition of the warning lights on the combination meter assembly.
Result | Proceed to |
|---|---|
Only the PCS warning light is illuminated |
A |
The PCS warning light is not illuminated |
|
The PCS warning light and other warning lights are illuminated or blinking |
B |
| B | GO TO MALFUNCTIONING SYSTEM |
|
INSPECT MULTI-INFORMATION DISPLAY
(a) Check if a pre-collision system warning message is displayed on the multi-information display in the combination meter assembly.
Result | Proceed to |
|---|---|
"Pre-Collision System Malfunction Visit Your Dealer" is displayed |
A |
Any of the following messages is displayed:
|
B |
Warning message is not displayed |
C |
| B | GO TO PROBLEM SYMPTOMS TABLE |
| C | CHECK CONDITIONS WHEN PRE-COLLISION SYSTEM DID NOT OPERATE |
|
CHECK FOR DTCs*
HINT:
Refer to DTC Check / Clear.
Click here ![]()
(a) Check for DTCs and note any codes that are output.
Body Electrical > Pre-Collision 2 > Trouble Codes(b) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(c) Recheck for DTCs.
(1) Attempt to duplicate the malfunction and check if the DTCs are output again.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
Malfunction is duplicated but DTCs are not output |
A |
Malfunction cannot be duplicated and DTCs are not output |
B |
DTCs are output |
C |
| B | GO TO SYMPTOM SIMULATION |
| C | GO TO DTC CHART |
|
PROBLEM SYMPTOMS TABLE
HINT:
Refer to Problem Symptoms Table.
Click here ![]()
Result | Proceed to |
|---|---|
Fault is not listed in Problem Symptoms Table |
A |
Fault is listed in Problem Symptoms Table |
B |
| B | GO TO STEP 11 |
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Terminals of ECU
Click here ![]()
(b) Data List / Active Test
Click here ![]()
|
ADJUST, REPAIR OR REPLACE
NOTICE:
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here ![]()
|
CONFIRMATION TEST
| NEXT | END |
ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Perform millimeter wave radar sensor assembly adjustment.
Click here ![]()
| NEXT | GO TO STEP 4 |
Initialization
INITIALIZATION
STEERING SENSOR ZERO POINT CALIBRATION
(a) Start the hybrid system.
(b) Drive the vehicle straight ahead at 35 km/h or more for 5 seconds or more.
(c) Turn the power switch off.
Operation Check
OPERATION CHECK
CHECK PRE-COLLISION SYSTEM SETTING
(a) Turn the power switch on (IG).
(b) Operate the steering pad switch assembly to change the setting of PCS on the multi-information display to "On" and check that the pre-collision system turns on.
HINT:
When the power switch is turned on (IG), the PCS will turn on. This can be changed through a customize setting using the Techstream.
(c) Operate the steering pad switch assembly to change the PCS setting to "Off" and check that the PCS warning light illuminates.
*a |
PCS Warning Light |
CHECK PRE-COLLISION SYSTEM SENSITIVITY SETTING
(a) Turn the power switch on (IG).
(b) Operate the steering pad switch assembly to select Change PCS Sensitivity and check that the warning timing adjustment display on the multi-information display changes between "Far", "Mid" and "Near" accordingly.
HINT:
- The pre-collision system warning timing status remains unchanged when the power switch is turned off and back to ON. This can be changed through a customize setting using the Techstream.
- The default setting is "Mid".
Parts Location
PARTS LOCATION
ILLUSTRATION
*1 |
FORWARD RECOGNITION CAMERA |
*2 |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
*3 |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL ECU |
- |
- |
ILLUSTRATION
*1 |
DRIVING SUPPORT ECU ASSEMBLY |
*2 |
COMBINATION METER ASSEMBLY - MULTI-INFORMATION DISPLAY - PCS WARNING LIGHT |
*3 |
STEERING PAD SWITCH ASSEMBLY |
*4 |
AIRBAG ECU ASSEMBLY - YAW RATE SENSOR |
*5 |
HYBRID VEHICLE CONTROL ECU |
*6 |
DLC3 |
ILLUSTRATION
*1 |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
*2 |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |
*3 |
STEERING SENSOR |
*4 |
VSC OFF SWITCH |
*5 |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU IG1 NO. 4 FUSE |
- |
- |
Precaution
PRECAUTION
HANDLING PRECAUTION FOR PRE-COLLISION SYSTEM
(a) In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate.
- When passing a vehicle or pedestrian
- When changing lanes while overtaking a preceding vehicle
- When overtaking a preceding vehicle that is changing lanes
- When overtaking a preceding vehicle that is making a left/right turn
- When passing a vehicle in an oncoming lane that is stopped to make a right/left turn
- When driving on a road where relative location to vehicle ahead in an adjacent lane may change, such as on a winding road
- When rapidly closing on a vehicle ahead
- If the front of the vehicle is raised or lowered, such as when the road surface is uneven or undulating
- When approaching objects on the roadside, such as guardrails, utility poles, trees, or walls
- When there is a vehicle, pedestrian, or object by the roadside at the entrance of a curve
- When driving on a narrow path surrounded by a structure, such as in a tunnel or on an iron bridge
- When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion on the road surface or roadside
- When a crossing pedestrian approaches very close to the vehicle
- When passing through a place with a low structure above the road (low ceiling, traffic sign, etc.)
- When passing under an object (billboard, etc.) at the top of an uphill road
- When rapidly closing on an electric toll gate barrier, parking area barrier, or other barrier that opens and closes
- When using an automatic car wash
- When driving through or under objects that may contact the vehicle, such as thick grass, tree branches, or a banner
- When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead
- When driving through steam or smoke
- When there are patterns or paint on the road or a wall that may be mistaken for a vehicle or pedestrian
- When driving near an object that reflects radio waves, such as a large truck or guardrail
- When driving near a TV tower, broadcasting station, electric power plant, or other location where strong radio waves or electrical noise may be present
(b) In some situations such as the following, a vehicle may not be detected by the millimeter wave radar sensor assembly and forward recognition camera, preventing the system from operating properly.
- If an oncoming vehicle is approaching your vehicle
- If a vehicle ahead is a motorcycle or bicycle
- When approaching the side or front of a vehicle
- If a preceding vehicle has a small rear end, such as an unloaded truck
- If a preceding vehicle has a low rear end, such as a low bed trailer
- If a vehicle ahead is carrying a load which protrudes past its rear bumper
- If a vehicle ahead has extremely high ground clearance
- If a vehicle ahead is irregularly shaped, such as a tractor or side car
- If the sun or other light is shining directly on a vehicle ahead
- If a vehicle cuts in front of your vehicle or emerges from beside a vehicle
- If a vehicle ahead makes an abrupt maneuver (such as sudden swerving, acceleration or deceleration)
- When suddenly cutting behind a preceding vehicle
- When a vehicle ahead is not directly in front of your vehicle
- When driving in inclement weather such as heavy rain, fog, snow or a sandstorm
- When the vehicle is hit by water, snow, dust, etc. from a vehicle ahead
- When driving through steam or smoke
- When driving in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a tunnel
- When a very bright light, such as the sun or the headlights of oncoming traffic, shines directly into the forward recognition camera
- When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel
- After the hybrid system has started the vehicle has not been driven for a certain amount of time
- While making a left/right turn and for a few seconds after making a left/right turn
- While driving on a curve and for a few seconds after driving on a curve
- If your vehicle is skidding
- If the front of the vehicle is raised or lowered
- If the wheels are misaligned
- If a wiper blade is blocking the forward recognition camera
- The vehicle is wobbling
- The vehicle is being driven at extremely high speeds
- When driving on a hill
- If the millimeter wave radar sensor assembly or forward recognition camera is misaligned
(c) In some situations such as the following, sufficient braking force may not be obtained, preventing the system from performing properly.
- If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet
- If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.)
- When the vehicle is being driven on a gravel road or other slippery surface
(d) Some pedestrians such as the following may not be detected by the millimeter wave radar sensor assembly and forward recognition camera, preventing the system from operating properly.
- Pedestrians shorter than approximately 1 m (3.2 ft.) or taller than approximately 2 m (6.5 ft.)
- Pedestrians wearing oversized clothing (a rain coat, long skirt, etc.), making their silhouette obscure
- Pedestrians who are carrying large baggage, holding an umbrella, etc., hiding part of their body
- Pedestrians who are bending forward or squatting
- Pedestrians who are pushing a stroller, wheelchair, bicycle or other vehicle
- Groups of pedestrians which are close together
- Pedestrians who are wearing white and look extremely bright
- Pedestrians in the dark, such as at night or while in a tunnel
- Pedestrians whose clothing appears to be nearly the same color or brightness as their surroundings
- Pedestrians near walls, fences, guardrails, or large objects
- Pedestrians who are on a metal object (manhole cover, steel plate, etc.) on the road
- Pedestrians who are walking fast
- Pedestrians who are changing speed abruptly
- Pedestrians running out from behind a vehicle or a large object
- Pedestrians who are extremely close to the side of the vehicle (outside rear view mirror, etc.)
(e) When the PCS warning light illuminates and a warning message is displayed on the multi-information display, the system may not temporarily operate, or it may have a malfunction.
HINT:
For details on the operation of the PCS warning light and displayed warning messages, refer to Diagnosis System.
Click here ![]()
(1) In the following situations, the warning light will turn off, the message will disappear and the system will become operational when normal operating conditions return.
- When the millimeter wave radar sensor assembly or forward recognition camera or the area around either sensor is hot, such as in the sun
- When the millimeter wave radar sensor assembly or forward recognition camera or the area around either sensor is cold, such as in an extremely cold environment
- When a millimeter wave radar sensor assembly or forward recognition camera is dirty or covered with snow, etc.
- When the part of the windshield glass in front of the forward recognition camera is fogged up or covered with condensation or ice
- If the forward recognition camera is obstructed, such as when the hood is open or a sticker is attached to the windshield glass near the forward recognition camera
- When automatic calibration is being performed after millimeter wave axis misalignment is detected
(f) If VSC is disabled, the pre-collision brake assist and pre-collision braking functions are also disabled.
HINT:
The PCS warning light will turn on and "VSC Turned Off Pre-collision Brake System Unavailable" will be displayed on the multi-information display.
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
NOTICE:
- When disconnecting the cable from the negative (-) auxiliary battery terminal, initialize the following systems after the cable is reconnected.
System Name
See Procedure
Lane Departure Alert System (w/ Steering Control)

Pre-collision System
Intelligent Clearance Sonar System
Lighting System (w/ Cornering Light)
Parking Assist Monitor System
Panoramic View Monitor System
- If the auxiliary battery has been discharged and charged or the cable has been disconnected and reconnected to the negative (-) auxiliary battery terminal, perform Steering Sensor Zero Point Calibration.
Click here

PRECAUTION BEFORE SERVICING
(a) Make sure to turn the pre-collision system off in the following situations, as it may operate unexpectedly or may not operate when necessary.
- When the vehicle is being towed
- When the vehicle is towing another vehicle
- When transporting the vehicle via truck, boat, train or similar means of transportation
- When the vehicle is raised on a lift with the hybrid system operating and the tires are allowed to rotate freely
- When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on vehicle wheel balancer
- When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons
- If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning
- When the vehicle is driven in a sporty manner or off-road
- When the tires are not properly inflated
- When the tires are very worn
- When tires of a size other than specified are installed
- When tire chains are installed
- When a compact spare tire or an emergency tire puncture repair kit is used
- If equipment (snow plow, etc.) that may obstruct the millimeter wave radar sensor assembly or forward recognition camera is temporarily installed to the vehicle
TROUBLESHOOTING PRECAUTIONS
(a) If a terminal contact malfunction or part installation problem occurs, removal and reinstallation of the suspected part may return the system to normal. However, be aware that the normal condition may only be temporary.
(b) Before disconnecting connectors or removing/installing parts, determine the malfunctioning area by checking and writing down the vehicle conditions (output DTCs, etc.) at the time the malfunction occurred.
(c) Be sure to check for DTCs related to other systems. The pre-collision system may be influenced by malfunctions in other systems.
(d) The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Click here ![]()
HANDLING PRECAUTIONS
(a) When removing and installing ECUs, sensors, switches or other pre-collision system related parts, perform the following:
- Make sure that the power switch is off unless otherwise specified in the procedure.
- After removal/installation, check for DTCs and confirm that a normal system code is output.
REPLACEMENT PRECAUTIONS
(a) DRIVING SUPPORT ECU ASSEMBLY:
(1) When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
(b) MILLIMETER WAVE RADAR SENSOR ASSEMBLY:
(1) When replacing the millimeter wave radar sensor assembly, always replace it with a new one. When a new millimeter wave radar sensor assembly is installed to the vehicle, it receives vehicle information from the driving support ECU assembly and stores it. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly and millimeter wave radar sensor assembly will not match and a DTC may be stored.
(2) If the millimeter wave radar sensor assembly has been replaced with a new one, be sure to perform Front Beam Axis Adjustment.
Click here ![]()
(c) FORWARD RECOGNITION CAMERA:
(1) If the forward recognition camera has been replaced with a new one or the windshield glass has been removed and installed, it is necessary to perform forward recognition camera adjustment. If the system is turned on without performing forward recognition camera adjustment, DTC C1AA9 will be stored.
Click here ![]()
(d) WINDSHIELD GLASS:
(1) When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket or the pre-collision system may not operate properly due to a difference in the transmissivity or black ceramic border.
(2) Do not attach stickers, including transparent stickers, or other items to the outer side of the windshield glass assembly within the area in front of the forward recognition camera.
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
- Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
- Inspect the fuses and relays related to this system before inspecting the suspected areas below.
- The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.
Symptom | Suspected Area | Link |
|---|---|---|
"Pre-Collision System Unavailable" is displayed |
History of millimeter wave radar sensor assembly front beam misalignment (vertical)* |
|
Perform millimeter wave radar sensor assembly adjustment |
||
Millimeter wave radar sensor assembly temperature malfunction |
||
Millimeter wave radar sensor assembly low voltage malfunction |
||
Millimeter wave radar sensor assembly |
||
Combination meter assembly |
||
Driving support ECU assembly |
||
"Pre-Collision System Unavailable Clean Sensor" is displayed |
Foreign matter attached to millimeter wave radar sensor assembly |
- |
Millimeter wave radar sensor assembly |
||
Combination meter assembly |
||
Driving support ECU assembly |
||
"Front Camera Unavailable" is displayed |
Check current condition of forward recognition camera based on related Data List items.
|
|
Forward recognition camera |
||
Combination meter assembly |
||
Driving support ECU assembly |
||
"Front Camera Unavailable Remove Debris On Windshield" is displayed |
Front of forward recognition camera or windshield glass is dirty or misty |
- |
Forward recognition camera |
||
Combination meter assembly |
||
Driving support ECU assembly |
||
Although there is possibility of collision, pre-collision controls (all controls) do not operate ("Pre-collision System Unavailable" is not displayed) |
Check if pre-collision system is canceled |
- |
Vehicle condition/environment does not match the pre-collision system operation conditions. |
||
Check installation condition of millimeter wave radar sensor assembly |
||
Perform millimeter wave radar sensor assembly adjustment |
||
Millimeter wave radar sensor assembly |
||
Check installation condition of forward recognition camera |
||
Perform forward recognition camera adjustment |
||
Forward recognition camera |
||
Driving support ECU assembly |
||
Although there is no possibility of collision, pre-collision controls (all controls) operate |
Vehicle condition/environment does not match the pre-collision system operation conditions. |
|
Check installation condition of millimeter wave radar sensor assembly |
||
Perform millimeter wave radar sensor assembly adjustment |
||
Millimeter wave radar sensor assembly |
||
Check installation condition of forward recognition camera |
||
Perform forward recognition camera adjustment |
||
Forward recognition camera |
||
Driving support ECU assembly |
||
Pre-collision system does not operate |
Check if pre-collision system is canceled |
- |
Driving support ECU assembly |
||
Pre-collision system cannot be canceled (PCS warning light does not illuminate) |
Combination meter assembly (check if indicator illuminates using Active Test) |
|
Driving support ECU assembly |
||
Combination meter assembly |
- *: If "Pre-Collision System Unavailable." is displayed on the multi-information display and there is front beam axis misalignment (vertical) history, the millimeter wave radar sensor assembly may be performing beam axis alignment correction. In this case, the message will disappear when the millimeter wave radar sensor assembly front beam axis adjustment has completed.
"Pre-Collision System Unavailable." disappears when the millimeter wave radar sensor assembly beam axis alignment correction has completed.
Make sure to delete the beam axis misalignment history when the millimeter wave radar sensor assembly beam axis alignment correction has completed.
Click here

System Diagram
SYSTEM DIAGRAM
Communication Table Sender | Receiver | Signal | Line |
|---|---|---|---|
Driving Support ECU Assembly |
Skid Control ECU (Brake Booster with Master Cylinder Assembly) |
|
CAN |
Driving Support ECU Assembly |
Combination Meter Assembly |
|
CAN |
Driving Support ECU Assembly |
Forward Recognition Camera |
|
CAN |
Skid Control ECU (Brake Booster with Master Cylinder Assembly) |
Driving Support ECU Assembly |
|
CAN |
Skid Control ECU (Brake Booster with Master Cylinder Assembly) |
Forward Recognition Camera |
|
CAN |
Yaw Rate Sensor (Airbag ECU Assembly) |
Driving Support ECU Assembly |
Vehicle yaw rate sensor signal |
CAN |
Yaw Rate Sensor (Airbag ECU Assembly) |
Forward Recognition Camera |
Vehicle yaw rate sensor signal |
CAN |
Main Body ECU (Multiplex Network Body ECU) |
Driving Support ECU Assembly |
Vehicle specification information (destination) |
CAN |
Main Body ECU (Multiplex Network Body ECU) |
Forward Recognition Camera |
Vehicle specification information (destination) |
CAN |
Steering Sensor |
Driving Support ECU Assembly |
|
CAN |
Steering Sensor |
Forward Recognition Camera |
Steering angle sensor malfunction signal |
CAN |
Hybrid Vehicle Control ECU |
Driving Support ECU Assembly |
|
CAN |
Millimeter Wave Radar Sensor Assembly |
Driving Support ECU Assembly |
|
CAN |
Forward Recognition Camera |
Driving Support ECU Assembly |
|
CAN |
Terminals Of Ecu
TERMINALS OF ECU
CHECK DRIVING SUPPORT ECU ASSEMBLY
(a) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G39-7 (B) - G39-28 (GND) |
B - W-B |
Power source |
Power switch on (IG) |
11 to 14 V |
Power switch off |
Below 1 V |
|||
G39-28 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(b) Check for pulses according to the value(s) in the table below.
HINT:
If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the driving support ECU assembly is suspected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G39-8 (CA1P) - G39-28 (GND) |
G - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 1) |
G39-9 (CA1N) - G39-28 (GND) |
W - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 2) |
G39-10 (CA2H) - G39-28 (GND) |
R - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 1) |
G39-11 (CA2L) - G39-28 (GND) |
W - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 2) |
(1) WAVEFORM 1
Item | Content |
|---|---|
Terminal Name |
Between G39-8 (CA1P) - G39-28 (GND) Between G39-10 (CA2H) - G39-28 (GND) |
Tester Range |
1 V/DIV., 10 μsec./DIV. |
Condition |
Power switch on (IG) |
HINT:
The waveform varies depending on the CAN communication signal.
(2) WAVEFORM 2
Item | Content |
|---|---|
Terminal Name |
Between G39-9 (CA1N) - G39-28 (GND) Between G39-11 (CA2L) - G39-28 (GND) |
Tester Range |
1 V/DIV., 10 μsec./DIV. |
Condition |
Power switch on (IG) |
HINT:
The waveform varies depending on the CAN communication signal.
CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
(a) Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A25-8 (IGB) - A25-1 (SGND) |
R - W-B |
Power source |
Power switch on (IG) |
11 to 14 V |
A25-1 (SGND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(b) Check for pulses according to the value(s) in the table below.
HINT:
If the waveform is not similar to that shown in the illustration, a malfunction of a CAN bus line, terminating resistor, or the millimeter wave radar sensor assembly is suspected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A25-3 (CA2H) - A25-1 (SGND) |
R - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 1) |
A25-2 (CA2L) - A25-1 (SGND) |
W - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 2) |
A25-5 (CA1P) - A25-1 (SGND) |
G - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 1) |
A25-6 (CA1N) - A25-1 (SGND) |
W - W-B |
CAN communication signal |
Power switch on (IG) |
Pulse generation (See waveform 2) |
(1) WAVEFORM 1
Item | Content |
|---|---|
Terminal Name |
Between A25-3 (CA2H) and A25-1 (SGND) Between A25-5 (CA1P) and A25-1 (SGND) |
Tester Range |
1 V/DIV., 10 μsec./DIV. |
Condition |
Power switch on (IG) |
HINT:
The waveform varies depending on the CAN communication signal.
(2) WAVEFORM 2
Item | Content |
|---|---|
Terminal Name |
Between A25-2 (CA2L) and A25-1 (SGND) Between A25-6 (CA1N) and A25-1 (SGND) |
Tester Range |
1 V/DIV., 10 μsec./DIV. |
Condition |
Power switch on (IG) |
HINT:
The waveform varies depending on the CAN communication signal.

Lost Communication with Front Camera Module (U023A)
DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
U023A |
Lost Communication with Front Camera Module |
When the power switch is on (IG), a communication error between the forward recognition camera and driving support ECU assembly is detected for approximately 3 seconds. |
|
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
- If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click here

HINT:
- Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.
PROCEDURE
READ VALUE USING TECHSTREAM (CAN BUS CHECK)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Can Bus Check.
Click here ![]()
Result | Proceed to |
|---|---|
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed |
A |
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK FOR DTCs
(a) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC U1002 is not output |
A |
DTC U1002 is output |
B |
| B | GO TO DTC CHART (U1002) |
|
CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the O5 forward recognition camera connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - O5-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(d) Connect the O5 forward recognition camera connector.
| OK | REPLACE FORWARD RECOGNITION CAMERA |
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA) |
Lost Communication with Yaw Rate Sensor Module (U0125,U0126,U0129,U0155,U0293)
DESCRIPTION
The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect objects in front of the vehicle. Based on signals from the millimeter wave radar sensor assembly, the driving support ECU assembly sends pre-collision system control operation signals. These DTCs are stored when a communication malfunction occurs between ECUs that perform pre-collision system control.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
U0125 |
Lost Communication with Yaw Rate Sensor Module |
When the power switch is on (IG), a communication error between the yaw rate sensor (airbag ECU assembly) and the driving support ECU assembly is detected for approximately 1 second. |
CAN communication system |
U0126 |
Lost Communication with Steering Angle Sensor Module |
When the power switch is on (IG), a communication error between the steering sensor and the driving support ECU assembly is detected for approximately 4 seconds. |
CAN communication system |
U0129 |
Lost Communication with Brake System Control Module |
When the power switch is on (IG), a communication error between the skid control ECU (brake booster with master cylinder assembly) and the driving support ECU assembly is detected for approximately 3 seconds. |
CAN communication system |
U0155 |
Lost Communication with Instrument Panel Cluster (IPC) Control Module |
When the power switch is on (IG), a communication error between the combination meter assembly and the driving support ECU assembly is detected for approximately 3 seconds. |
CAN communication system |
U0293 |
Lost Communication with HV ECU |
When the vehicle is being driven at a speed of 5 km/h or more, a communication error between the hybrid vehicle control ECU and the driving support ECU assembly is detected for approximately 5 seconds. |
CAN communication system |
PROCEDURE
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC U0125, U0126, U0129, U0155 and U0293 are not output |
A |
DTC U0125, U0126, U0129, U0155 or U0293 is output |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | GO TO CAN COMMUNICATION SYSTEM |
Lost Communication with Cruise Control Front Distance Range Sensor (U0235)
DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
U0235 |
Lost Communication with Cruise Control Front Distance Range Sensor |
When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second. |
|
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

HINT:
- Operating the power switch, any other switches or a door triggers related ECUs and sensors to communicate using the CAN communication system. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the connectors of ECUs or wire harnesses while performing the inspection below may help determine the cause of the malfunction.
PROCEDURE
READ VALUE USING TECHSTREAM (CAN BUS CHECK)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Can Bus Check.
Click here ![]()
Result | Proceed to |
|---|---|
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed |
A |
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK FOR DTCs
(a) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC U1002 is not output |
A |
DTC U1002 is output |
B |
| B | GO TO DTC CHART (U1002) |
|
CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A25 millimeter wave radar sensor assembly connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A25-5 (CA1P) - A25-6 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(d) Connect the A25 millimeter wave radar sensor assembly connector.
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
|
CHECK FOR DTCs
(a) Check for DTCs.
Chassis > Front Recognition Camera > Trouble CodesResult | Proceed to |
|---|---|
DTC U0235 is not output |
A |
DTC U0235 is output |
B |
| A | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
| B | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
Lost Communication with Gateway Module (U1002)
DESCRIPTION
This DTC is stored when the driving support ECU assembly cannot receive signals from the forward recognition camera or millimeter wave radar sensor assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
U1002 |
Lost Communication with Gateway Module |
After the power switch is turned on, communication between the driving support ECU assembly and any of the following components is abnormal for 2 seconds or more
|
|
WIRING DIAGRAM
NOTICE:
- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
- If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click here

HINT:
- Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
PROCEDURE
CHECK CAN BUS LINE (MALFUNCTION CONFIRMATION)
(a) Turn the power switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
Result | Proceed to |
|---|---|
OK |
A |
NG (Open circuit in main line or Driving support ECU assembly branch line) |
B |
NG (Short circuit between main lines) |
C |
NG (Short to +B or ground) |
D |
| B | GO TO STEP 3 |
| C | GO TO STEP 8 |
| D | GO TO STEP 12 |
|
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC U1002 is not output |
A |
DTC U1002 is output |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
CHECK FOR OPEN IN CAN BUS BRANCH LINES (DRIVING SUPPORT ECU ASSEMBLY)
(a) Disconnect the G39 driving support ECU assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G39-8 (CA1P) - G39-9 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
HINT:
If the resistance is between 108 and 132 Ω, there may be an open in a CAN bus main line. If the value is 132 Ω or more, there may be an open in a CAN bus branch line between the No. 8 CAN junction connector and the driving support ECU assembly or a connector may be disconnected.
(c) Connect the G39 driving support ECU assembly connector.
| NG | GO TO STEP 7 |
|
CHECK FOR OPEN IN CAN BUS MAIN LINES (NO. 8 CAN JUNCTION CONNECTOR)
(a) Disconnect the G92 No. 8 CAN junction connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
G92-6 - G92-17 |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
Forward Recognition Camera |
G92-5 - G92-16 |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
Millimeter Wave Radar Sensor Assembly |
(c) Connect the G92 No. 8 CAN junction connector.
Result | Proceed to |
|---|---|
OK |
A |
NG (Forward Recognition Camera Main Line) |
B |
NG (Millimeter Wave Radar Sensor Assembly Main Line) |
C |
| A | REPLACE NO. 8 CAN JUNCTION CONNECTOR |
| C | GO TO STEP 6 |
|
CHECK FOR OPEN IN CAN BUS MAIN LINES (FORWARD RECOGNITION CAMERA)
(a) Disconnect the O5 forward recognition camera connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - O5-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(c) Connect the O5 forward recognition camera connector.
| OK | REPLACE FORWARD RECOGNITION CAMERA |
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA) |
CHECK FOR OPEN IN CAN BUS MAIN LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
(a) Disconnect the A25 millimeter wave radar sensor assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A25-5 (CA1P) - A25-6 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(c) Connect the A25 millimeter wave radar sensor assembly connector.
| OK | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
CHECK FOR OPEN IN CAN BUS BRANCH LINES (NO. 8 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY)
(a) Disconnect the G39 driving support ECU assembly connector. |
|
(b) Disconnect the G92 No. 8 CAN junction connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G92-7 - G39-8 (CA1P) |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
G92-18 - G39-9 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
(d) Connect the G92 No. 8 CAN junction connector.
(e) Connect the G39 driving support ECU assembly connector.
| OK | REPLACE NO. 8 CAN JUNCTION CONNECTOR |
| NG | REPAIR OR REPLACE CAN BUS BRANCH WIRE (NO. 8 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY) |
CHECK FOR SHORT BETWEEN CAN BUS LINES (FORWARD RECOGNITION CAMERA)
(a) Disconnect the O5 forward recognition camera connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - O5-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(c) Connect the O5 forward recognition camera connector.
| OK | REPLACE FORWARD RECOGNITION CAMERA |
|
CHECK FOR SHORT BETWEEN CAN BUS LINES (NO. 8 CAN JUNCTION CONNECTOR)
(a) Disconnect the G92 No. 8 CAN junction connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
G92-6 - G92-17 |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
Forward Recognition Camera |
G92-5 - G92-16 |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
Millimeter Wave Radar Sensor Assembly |
G92-7 - G92-18 |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Driving Support ECU Assembly |
(c) Connect the G92 No. 8 CAN junction connector.
Result | Proceed to |
|---|---|
OK |
A |
NG (Forward Recognition Camera Main Line) |
B |
NG (Millimeter Wave Radar Sensor Assembly Main Line) |
C |
NG (Driving Support ECU Assembly Branch Line) |
D |
| A | REPLACE NO. 8 CAN JUNCTION CONNECTOR |
| B | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA) |
| D | GO TO STEP 11 |
|
CHECK FOR SHORT BETWEEN CAN BUS LINES (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
(a) Disconnect the A25 millimeter wave radar sensor assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A25-5 (CA1P) - A25-6 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
(c) Connect the A25 millimeter wave radar sensor assembly connector.
| OK | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
CHECK FOR SHORT BETWEEN CAN BUS LINES (DRIVING SUPPORT ECU ASSEMBLY)
(a) Disconnect the G39 driving support ECU assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G39-8 (CA1P) - G39-9 (CA1N) |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
(c) Connect the G39 driving support ECU assembly connector.
| OK | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
| NG | REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY) |
CHECK FOR SHORT IN CAN BUS LINE (FORWARD RECOGNITION CAMERA)
(a) Disconnect the O5 forward recognition camera connector.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Forward Recognition Camera) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
O5-12 (CANL) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
O5-6 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
O5-12 (CANL) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
(c) Connect the O5 forward recognition camera connector.
| OK | REPLACE FORWARD RECOGNITION CAMERA |
|
CHECK FOR SHORT IN CAN BUS LINE (NO. 8 CAN JUNCTION CONNECTOR)
(a) Disconnect the G92 No. 8 CAN junction connector.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to No. 8 CAN Junction Connector) |
*b |
to Forward Recognition Camera |
*c |
to Millimeter Wave Radar Sensor Assembly |
*d |
to Driving Support ECU Assembly |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
G92-6 - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Forward Recognition Camera |
G92-17 - G45-4 (CG) |
|||
G92-6 - G45-16 (BAT) |
6 kΩ or higher |
||
G92-17 - G45-16 (BAT) |
|||
G92-5 - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Millimeter Wave Radar Sensor Assembly |
G92-16 - G45-4 (CG) |
|||
G92-5 - G45-16 (BAT) |
6 kΩ or higher |
||
G92-16 - G45-16 (BAT) |
|||
G92-7 - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Driving Support ECU Assembly |
G92-18 - G45-4 (CG) |
|||
G92-7 - G45-16 (BAT) |
6 kΩ or higher |
||
G92-18 - G45-16 (BAT) |
(c) Connect the G92 No. 8 CAN junction connector.
Result | Proceed to |
|---|---|
OK |
A |
NG (Forward Recognition Camera Main Line) |
B |
NG (Millimeter Wave Radar Sensor Assembly Main Line) |
C |
NG (Driving Support ECU Assembly Branch Line) |
D |
| A | REPLACE NO. 8 CAN JUNCTION CONNECTOR |
| B | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - FORWARD RECOGNITION CAMERA) |
| D | GO TO STEP 15 |
|
CHECK FOR SHORT IN CAN BUS LINE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
(a) Disconnect the A25 millimeter wave radar sensor assembly connector.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A25-5 (CA1P) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A25-6 (CA1N) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A25-5 (CA1P) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A25-6 (CA1N) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
(c) Connect the A25 millimeter wave radar sensor assembly connector.
| OK | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
| NG | REPAIR OR REPLACE CAN BUS MAIN LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - MILLIMETER WAVE RADAR SENSOR ASSEMBLY) |
CHECK FOR SHORT IN CAN BUS LINE (DRIVING SUPPORT ECU ASSEMBLY)
(a) Disconnect the G39 driving support ECU assembly connector.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Driving Support ECU Assembly) |
- |
- |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G39-8 (CA1P) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G39-9 (CA1N) - G45-4 (CG) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G39-8 (CA1P) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G39-9 (CA1N) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
(c) Connect the G39 driving support ECU assembly connector.
| OK | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
| NG | REPAIR OR REPLACE CAN BUS BRANCH LINE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - DRIVING SUPPORT ECU ASSEMBLY) |
Lost Communication with Driving Support ECU (U1104)
DESCRIPTION
The driving support ECU assembly is connected to the millimeter wave radar sensor assembly, forward recognition camera and skid control ECU (brake booster with master cylinder assembly) via CAN communication. If communication with the millimeter wave radar sensor assembly, forward recognition camera or skid control ECU (brake booster with master cylinder assembly) stops, the driving support ECU assembly stores DTC U1104.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
U1104 |
Lost Communication with Driving Support ECU |
Any of the following conditions is met:
|
|
Vehicle Condition |
||||
|---|---|---|---|---|
Pattern 1 | Pattern 2 | Pattern 3 |
||
Diagnosis Condition |
Power switch is on (IG) |
○ |
○ |
○ |
Malfunction Status |
A communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected |
○ |
- |
- |
A communication error between the driving support ECU assembly and the forward recognition camera is detected |
- |
○ |
- |
|
A communication error between the driving support ECU assembly and the skid control ECU (brake booster with master cylinder assembly) is detected |
- |
- |
○ |
|
Detection Time |
Approximately 0.2 seconds or more |
Approximately 0.3 seconds or more |
Approximately 1.5 seconds or more |
|
Number of Trips |
1 trip |
1 trip |
1 trip |
|
HINT:
DTC will be stored when conditions of any pattern in the table above are met.
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
- If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera adjustment.
Click here

- When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
- When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here

- Confirm that the connectors are securely connected, as a partially connected connector can cause this DTC to be stored.
PROCEDURE
READ VALUE USING TECHSTREAM (CAN BUS CHECK)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: System Select / Can Bus Check.
Click here ![]()
Result | Proceed to |
|---|---|
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed |
A |
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
CHECK FOR DTCs
(a) Check for DTCs.
Chassis > Front Recognition Camera > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output |
A |
Only DTC U0235 is output |
B |
Only DTC U1104 is output |
C |
DTC U0235 and U1104 are output |
D |
| B | GO TO STEP 6 |
| C | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
| D | GO TO STEP 7 |
|
CHECK FOR DTCs
(a) Check for DTCs.
Chassis > ABS/VSC/TRAC > Trouble CodesResult | Proceed to |
|---|---|
Electronically controlled brake system DTCs are not output |
A |
Electronically controlled brake system DTCs are output |
B |
| B | GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM |
|
TEST MODE INSPECTION (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
HINT:
When entering Test Mode (Signal Check), the skid control ECU (brake booster with master cylinder assembly) communicates with the driving support ECU assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check).
(a) Procedure to Enter Test Mode (Signal Check)
(1) Turn the power switch off.
(2) Check that the steering wheel is centered.
(3) Check that the shift lever is in P.
(4) Connect the Techstream to the DLC3.
(5) Turn the power switch on (IG).
(6) Turn the Techstream on.
(7) Switch the skid control ECU (brake booster with master cylinder assembly) to Test Mode (Signal Check) using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.
HINT:
Do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check). If Test Mode (Signal Check) is exited within 5 seconds of entering Test Mode (Signal Check), DTC U1104 may be stored. If DTC U1104 is output after exiting Test Mode (Signal Check), enter Test Mode (Signal Check) again, wait at least 5 seconds, then recheck for DTCs.
Chassis > ABS/VSC/TRAC > UtilitySignal Check
(8) Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
HINT:
If the ABS warning light, brake warning light / yellow (minor malfunction) or slip indicator light remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.
(b) End of Test Mode (Signal Check)
(1) End Test Mode (signal check) using the Techstream
- Turn the power switch off and enter normal mode.
- Remove the Techstream.
|
CHECK FOR DTCs
(a) Clear the DTCs.
Body Electrical > Pre-Collision 2 > Clear DTCs(b) Make sure that the DTC detection conditions are met.
HINT:
If the detection conditions are not met, the system cannot detect the malfunction.
(c) Check for DTCs.
Body Electrical > Pre-Collision 2 > Trouble CodesResult | Proceed to |
|---|---|
DTC U1104 is not output |
A |
DTC U1104 is output |
B |
| A | END |
| B | REPLACE DRIVING SUPPORT ECU ASSEMBLY |
CHECK CAN BUS LINE
(a) Turn the power switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
(c) Disconnect the O5 forward recognition camera connector. |
|
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - O5-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
HINT:
If the result is not as specified, a malfunction in a CAN communication line is suspected.
(e) Connect the O5 forward recognition camera connector.
| OK | REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE) |
CHECK CAN BUS LINE
(a) Turn the power switch off.
(b) Disconnect the cable from the negative (-) auxiliary battery terminal.
(c) Disconnect the O5 forward recognition camera connector. |
|
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O5-6 (CANH) - O5-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
HINT:
If the result is not as specified, a malfunction in a CAN communication line is suspected.
(e) Connect the O5 forward recognition camera connector.
| OK | REPLACE FORWARD RECOGNITION CAMERA |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (CAN BUS LINE) |
Utility
UTILITY
NOTICE:
- When replacing a millimeter wave radar sensor assembly, replace it with a new one. When the millimeter wave radar sensor assembly is replaced with a new one, it stores the country specification information received from the driving support ECU assembly.
If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
- If the millimeter wave radar sensor assembly has been replaced or removed/installed, be sure to perform Front Beam Axis Adjustment. If not performed, DTC C1A14 will be stored when the system is turned on.
CONTROL MODE
HINT:
- This mode is used to check the operation of the pre-collision system when reproducing situations when the pre-collision system operated unnecessarily.
- Operating the pre-collision brake assist control or pre-collision braking control when reproducing problem symptoms may lead to a dangerous situation. To avoid this, do not attempt to operate the pre-collision braking control, only operate the pre-collision warning control (buzzer and warning message) when reproducing the problem symptoms.
PCS Control Operated
Buzzer Sound
Pre-collision warning control
Intermittent (Long)
Pre-collision brake assist control
Intermittent (Short)
Pre-collision braking control
Continuous
(a) Connect the Techstream to the DLC3.
(b) Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / Control Mode.
(c) Perform Control Mode according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > UtilityControl Mode
FRONT BEAM AXIS ADJUSTMENT
HINT:
Front Beam Axis Adjustment of the millimeter wave radar sensor assembly is performed using the Techstream.
(a) Perform Front Beam Axis Adjustment according to the display on the Techstream.
Click here ![]()
Front Beam Axis Adjustment
FRONT BEAM AXIS MISALIGNMENT READING
HINT:
The amount of misalignment of the millimeter wave radar sensor assembly can be checked using the Techstream.
(a) Perform Front Beam Axis Misalignment Reading according to the display on the Techstream.
Click here ![]()
Front Beam Axis Misalignment Reading
FRONT BEAM AXIS OFFSET READING
HINT:
The offset of the millimeter wave radar sensor assembly can be checked using the Techstream.
(a) Perform Front Beam Axis Offset Reading according to the display on the Techstream.
Click here ![]()
Front Beam Axis Offset Reading
HISTORY CLEAR
HINT:
If the status of any history data is "ON", clear the history data.
(a) Connect the Techstream to the DLC3.
(b) Enter the following menus: Body Electrical / Pre-Collision 2 / Utility / History Clear.
(c) Perform History Clear according to the display on the Techstream.
Body Electrical > Pre-Collision 2 > UtilityHistory Clear
Vehicle Control History
VEHICLE CONTROL HISTORY
VEHICLE CONTROL HISTORY
(a) A part of the control history can be confirmed using the vehicle control history.
Click here ![]()










