Front Door Pressure Sensor LH (B167A,B167E,B167F). Lost Communication with Front Door Pressure Sensor LH (B167B,B167C). Airbag ECU Malfunction1 (B1160-B1167)
Front Door Pressure Sensor LH (B167A,B167E,B167F)
DESCRIPTION
The side collision sensor LH circuit (bus 1) consists of the airbag ECU assembly, side airbag pressure sensor LH and side No. 2 airbag sensor LH.
The side airbag pressure sensor LH and side No. 2 airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side airbag pressure sensor LH.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B167A |
Front Door Pressure Sensor LH |
|
|
Comes on |
Does not apply to test/check mode |
B167E |
Front Door Pressure Sensor Threshold Malfunction (LH) |
|
|
Comes on |
Does not apply to test/check mode |
B167F |
Front Door Pressure Sensor LH Circuit Range/Performance |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
Click here ![]()
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK SIDE AIRBAG PRESSURE SENSOR LH
(a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminals to disable the SRS system.
(c) Interchange the side airbag pressure sensor LH with RH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B166B, B166C, B166F, B167A, B167E and B167F may be output at this time, but they are not related to this check.
Result | Proceed to |
|---|---|
DTC B167A, B167E or B167F is output. |
A |
DTC B166B, B166C or B166F is output. |
B |
DTCs B166B, B166C, B166F, B167A, B167E and B167F are not output. |
C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | REPLACE SIDE AIRBAG PRESSURE SENSOR LH |
| C | USE SIMULATION METHOD TO CHECK |
Lost Communication with Front Door Pressure Sensor LH (B167B,B167C)
DESCRIPTION
The side collision sensor LH circuit (bus 1) consists of the airbag ECU assembly, side airbag pressure sensor LH and side No. 2 airbag sensor LH.
The side airbag pressure sensor LH and side No. 2 airbag sensor LH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B167B |
Lost Communication with Front Door Pressure Sensor LH |
|
|
Comes on |
Does not apply to test/check mode |
B167C |
Front Door Pressure Sensor LH Initialization Incomplete |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK CONNECTION OF CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the side airbag pressure sensor LH and side No. 2 airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.
OK:
The connectors are properly connected.
| NG | CONNECT CONNECTORS PROPERLY |
|
CHECK CONNECTORS
(a) Disconnect the connectors from the side airbag pressure sensor LH and side No. 2 airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG | REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH |
|
CHECK WIRE HARNESS
(a) Connect the connectors that link the floor wire and front door wire LH. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K31-1 (BDL+) - Body ground |
Engine switch on (IG) |
Below 1 V |
K31-2 (BDL-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K31-1 (BDL+) - K31-2 (BDL-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector E.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K31-1 (BDL+) - K31-2 (BDL-) |
Always |
1 MΩ or higher |
K31-1 (BDL+) - Body ground |
Always |
1 MΩ or higher |
K31-2 (BDL-) - Body ground |
Always |
1 MΩ or higher |
| NG | GO TO STEP 5 |
|
CHECK SIDE AIRBAG PRESSURE SENSOR LH
(a) Connect the connector to the side No. 2 airbag sensor LH. |
|
(b) Interchange the side airbag pressure sensor LH with RH and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
Result | Proceed to |
|---|---|
DTC B167B or B167C is output. |
A |
DTC B166D or B166E is output. |
B |
DTCs B166D, B166E, B167B and B167C are not output. |
C |
(i) Turn the engine switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | REPLACE SIDE AIRBAG PRESSURE SENSOR LH |
| C | USE SIMULATION METHOD TO CHECK |
CHECK FLOOR WIRE
(a) Disconnect the floor wire connector from the front door wire LH. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK2-23 (BDL+) - Body ground |
Engine switch on (IG) |
Below 1 V |
IK2-41 (BDL-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK2-23 (BDL+) - IK2-41 (BDL-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK2-23 (BDL+) - IK2-41 (BDL-) |
Always |
1 MΩ or higher |
IK2-23 (BDL+) - Body ground |
Always |
1 MΩ or higher |
IK2-41 (BDL-) - Body ground |
Always |
1 MΩ or higher |
| OK | REPLACE FRONT DOOR WIRE LH |
| NG | REPLACE FLOOR WIRE |
Airbag ECU Malfunction1 (B1160-B1167)
DESCRIPTION
The airbag ECU assembly consists of the acceleration sensor, safing sensor, drive circuit, diagnosis circuit, ignition control, etc.
If the airbag ECU assembly receives signals from the acceleration sensor and pressure sensor, it determines whether the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the airbag ECU assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B1160 |
Airbag ECU Malfunction1 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1161 |
Airbag ECU Malfunction2 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1162 |
Airbag ECU Malfunction3 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1163 |
Airbag ECU Malfunction4 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1164 |
Airbag ECU Malfunction5 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1165 |
Airbag ECU Malfunction6 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1166 |
Airbag ECU Malfunction7 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
B1167 |
Airbag ECU Malfunction8 |
Airbag ECU assembly malfunction |
Airbag ECU assembly |
Comes on |
Does not apply to test/check mode |
HINT:
If any DTCs other than B1160, B1161, B1162, B1163, B1164, B1165, B1166 and B1167 are also output, troubleshoot those DTCs first.
PROCEDURE
CHECK DTC
(a) Turn the engine switch on (IG), and wait for at least 60 seconds.
(b) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesNOTICE:
If only DTC B1160, B1161, B1162, B1163, B1164, B1165, B1166 or B1167 is output, do not clear the DTC, replace the airbag ECU assembly.
Result | Proceed to |
|---|---|
Only DTC B1160, B1161, B1162, B1163, B1164, B1165, B1166 or B1167 is output |
A |
DTC B1160, B1161, B1162, B1163, B1164, B1165, B1166 or B1167 and other DTCs are output |
B |
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |



