Air Conditioning Unit(for 2gr-fks)
Components
COMPONENTS
ILLUSTRATION
*1 |
FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
*1 |
INLET HEATER WATER HOSE |
*2 |
NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY |
*3 |
OUTLET HEATER WATER HOSE |
*4 |
O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 12 or equivalent |
- |
- |
ILLUSTRATION
*A |
w/ Intelligent Parking Assist System |
*B |
w/ Active Noise Control System |
*1 |
COOLER (ROOM TEMP. SENSOR) THERMISTOR |
*2 |
DCM (TELEMATICS TRANSCEIVER) WITH BRACKET |
*3 |
DRIVING SUPPORT ECU ASSEMBLY |
*4 |
ECU INTEGRATION BOX RH |
*5 |
NO. 1 CLEARANCE WARNING BUZZER |
*6 |
STEREO COMPONENT EQUALIZER ASSEMBLY |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
ACCELERATOR PEDAL |
*2 |
ACCELERATOR PEDAL PAD |
*3 |
FLOOR CARPET BRACKET LH |
*4 |
FLOOR CARPET BRACKET RH |
*5 |
NO. 1 CONSOLE BOX DUCT |
*6 |
NO. 3 DASH PANEL INSULATOR PAD |
*7 |
REAR NO. 1 AIR DUCT |
*8 |
REAR NO. 2 AIR DUCT |
*9 |
REAR NO. 3 AIR DUCT |
*10 |
REAR NO. 4 AIR DUCT |
*11 |
FRONT FLOOR CARPET ASSEMBLY |
*12 |
FRONT FLOOR CARPET CLIP |
*13 |
CLIP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU |
*2 |
NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
*3 |
NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
*4 |
NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY |
*5 |
RELAY BLOCK HOLDER |
*6 |
EARTH WIRE |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
*1 |
AIR CONDITIONER UNIT ASSEMBLY |
*2 |
INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY |
*3 |
INSTRUMENT PANEL REINFORCEMENT ASSEMBLY |
*4 |
FRONT FLOOR MAT |
*5 |
CONNECTOR HOLDER |
*6 |
HOLE PLUG |
*7 |
EARTH WIRE |
*8 |
COOLER UNIT DRAIN HOSE GROMMET |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |
ILLUSTRATION
*1 |
AIR CONDITIONING AMPLIFIER ASSEMBLY |
*2 |
AIR CONDITIONING HARNESS ASSEMBLY |
*3 |
ASPIRATOR |
*4 |
BLOWER ASSEMBLY |
*5 |
NO. 2 AIR DUCT |
*6 |
NO. 2 AIR DUCT SUB-ASSEMBLY |
*7 |
NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
*8 |
AIR CONDITIONING RADIATOR ASSEMBLY |
● |
Non-reusable part |
- |
- |
ILLUSTRATION
*1 |
COOLER EXPANSION VALVE |
*2 |
COOLING UNIT PARTS |
*3 |
DRAIN COOLER HOSE |
*4 |
HEATER CLAMP |
*5 |
HEATER COVER |
*6 |
HEATER PIPE GROMMET |
*7 |
HEATER RADIATOR UNIT SUB-ASSEMBLY |
*8 |
NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
*9 |
NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
*10 |
NO. 1 COOLER THERMISTOR |
*11 |
NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
*12 |
UPPER HEATER CASE |
*13 |
LOWER HEATER CASE |
*14 |
O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 12 or equivalent |
- |
- |
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
2. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Click here ![]()
3. REMOVE NO. 2 AIR DUCT
Click here ![]()
4. REMOVE ASPIRATOR
Click here ![]()
5. REMOVE BLOWER ASSEMBLY
Click here ![]()
6. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY
Click here ![]()
7. REMOVE AIR CONDITIONING HARNESS ASSEMBLY
(a) Disconnect each connector. |
![]() |
(b) Disengage each clamp to remove the air conditioning harness assembly.
8. REMOVE HEATER COVER
(a) Remove the screw.
![]() |
Remove in this Direction |
(b) Remove the heater cover as shown in the illustration.
9. REMOVE DRAIN COOLER HOSE
Click here ![]()
10. REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
11. REMOVE NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
12. REMOVE HEATER PIPE GROMMET
Click here ![]()
13. REMOVE HEATER CLAMP
Click here ![]()
14. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
Click here ![]()
15. REMOVE COOLING UNIT PARTS
Click here ![]()
16. REMOVE COOLER EXPANSION VALVE
Click here ![]()
17. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
(a) Remove the 2 screws.
(b) Disengage the 10 claws to remove the upper heater case with No. 1 cooler evaporator sub-assembly from the lower heater case.
(c) Disengage the clamp. |
![]() |
(d) Remove the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor from the upper heater case.
18. REMOVE NO. 1 COOLER THERMISTOR
Click here ![]()
Installation
INSTALLATION
PROCEDURE
1. TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
Click here ![]()
2. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
NOTICE:
- Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
- When installing the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
(a) Connect each connector.
![]() |
Install in this Direction |
- |
- |
(b) Engage each clamp.
(c) Temporarily install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
(d) Install the 4 bolts (A).
![]() |
Bolt (A) |
![]() |
Bolt (B) |
![]() |
Nut |
- |
- |
Torque:
25 N·m {255 kgf·cm, 18 ft·lbf}
(e) Connect the brake pedal assembly with the bolt (B).
Torque:
15 N·m {153 kgf·cm, 11 ft·lbf}
(f) Temporarily install the nut.
(g) Install the 3 bolts.
Torque:
25 N·m {255 kgf·cm, 18 ft·lbf}
(h) Install the 2 hole plugs.
(i) Install a new cooler unit drain hose grommet. NOTICE:
|
|
(j) Connect the drain cooler hose.
(k) Install the front floor mat to its original position as shown in the illustration. |
![]() |
(l) Engage each clamp.
*a |
Lock Lever |
![]() |
Move in this Direction |
(m) Temporarily connect the connector and then move the lock lever as shown in the illustration to securely connect the connector.
NOTICE:
When connecting any airbag connector, take care not to damage the airbag wire harness.
(n) Check that there is no looseness in the installed parts of the airbag sensor assembly.
(o) Connect the connector.
(p) Engage each clamp.
(q) Connect the connector holder with the 2 nuts.
Torque:
8 N·m {82 kgf·cm, 71 in·lbf}
(r) Connect the 3 earth wires with the 3 bolts.
Torque:
8,5 N·m {87 kgf·cm, 75 in·lbf}
(s) Connect the connector.
3. INSTALL INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
Click here ![]()
4. INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Click here ![]()
5. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Click here ![]()
6. INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
(a) Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Torque:
Bolt :
20 N·m {204 kgf·cm, 15 ft·lbf}
Nut :
18 N·m {184 kgf·cm, 13 ft·lbf}
(b) Temporarily install the screw.
HINT:
Do not fully tighten the screw.
(c) Engage each clamp.
(d) Connect the earth wire with the bolt.
Torque:
8,5 N·m {87 kgf·cm, 75 in·lbf}
7. INSTALL AIR CONDITIONER UNIT ASSEMBLY
Click here ![]()
8. INSTALL NO. 3 DASH PANEL INSULATOR PAD
Click here ![]()
9. INSTALL NO. 1 CONSOLE BOX DUCT
Click here ![]()
10. INSTALL FLOOR CARPET BRACKET LH
Click here ![]()
11. INSTALL FLOOR CARPET BRACKET RH
Click here ![]()
12. INSTALL REAR NO. 3 AIR DUCT
Click here ![]()
13. INSTALL REAR NO. 4 AIR DUCT
Click here ![]()
14. INSTALL REAR NO. 1 AIR DUCT
Click here ![]()
15. INSTALL REAR NO. 2 AIR DUCT
Click here ![]()
16. INSTALL ACCELERATOR PEDAL
Click here ![]()
17. INSTALL ACCELERATOR PEDAL PAD
Click here ![]()
18. INSTALL COOLER (ROOM TEMP. SENSOR) THERMISTOR
Click here ![]()
19. INSTALL DRIVING SUPPORT ECU ASSEMBLY
Click here ![]()
20. INSTALL NO. 1 CLEARANCE WARNING BUZZER (w/ Intelligent Parking Assist System)
Click here ![]()
21. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
Click here ![]()
22. INSTALL STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System)
Click here ![]()
23. INSTALL ECU INTEGRATION BOX RH
Click here ![]()
24. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
25. INSTALL STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
Click here ![]()
for Power Tilt and Power Telescopic Steering Column:
Click here ![]()
26. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY
Click here ![]()
27. INSTALL FRONT SEAT ASSEMBLY LH
Click here ![]()
28. INSTALL FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
29. CONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
(a) Remove the vinyl tape from the No. 2 air conditioning tube and accessory assembly.
(b) Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 2 air conditioning tube and accessory assembly.
Compressor Oil:
ND-OIL 12 or equivalent
(c) Install the 2 O-rings to the No. 2 air conditioning tube and accessory assembly.
NOTICE:
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
(d) Connect the No. 2 air conditioning tube and accessory assembly.
(e) Rotate the hook connector as shown in the illustration. |
![]() |
(f) Insert the tube joint into the fitting hole securely and install the bolt.
Torque:
9,8 N·m {100 kgf·cm, 87 in·lbf}
30. CONNECT INLET HEATER WATER HOSE
(a) Connect the inlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration. NOTICE: Do not apply excessive force to the inlet heater water hose. |
|
31. CONNECT OUTLET HEATER WATER HOSE
(a) Connect the outlet heater water hose with the marking facing up and engage the clip within the area shown in the illustration. NOTICE: Do not apply excessive force to the outlet heater water hose. |
|
32. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here ![]()
33. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here ![]()
34. ADD ENGINE COOLANT
Click here ![]()
35. INSPECT FOR COOLANT LEAK
Click here ![]()
36. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
Click here ![]()
37. WARM UP ENGINE
Click here ![]()
38. INSPECT FOR REFRIGERANT LEAK
Click here ![]()
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL NO. 1 COOLER THERMISTOR
Click here ![]()
2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
(a) Install the No. 1 cooler evaporator sub-assembly with No. 1 cooler thermistor to the upper heater case. |
![]() |
(b) Engage the clamp.
(c) Engage the 10 claws to install the upper heater case with No. 1 cooler evaporator sub-assembly to the lower heater case.
(d) Install the 2 screws.
3. INSTALL COOLER EXPANSION VALVE
(a) Sufficiently apply compressor oil to 2 new O-rings and the fitting surfaces of the No. 1 cooler evaporator sub-assembly.
Compressor Oil:
ND-OIL 12 or equivalent
(b) Install the 2 O-rings to the No. 1 cooler evaporator sub-assembly.
NOTICE:
Keep the O-rings and O-ring fitting surfaces free of foreign matter.
(c) Using a 4 mm hexagon socket wrench, install the cooler expansion valve with the 2 hexagon bolts. Torque: 3,5 N·m {36 kgf·cm, 31 in·lbf} |
![]() |
4. INSTALL COOLING UNIT PARTS
Click here ![]()
5. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
Click here ![]()
6. INSTALL HEATER CLAMP
Click here ![]()
7. INSTALL HEATER PIPE GROMMET
Click here ![]()
8. INSTALL NO. 2 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
9. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
10. INSTALL DRAIN COOLER HOSE
Click here ![]()
11. INSTALL HEATER COVER
![]() |
Install in this Direction |
(a) Install the heater cover as shown in the illustration.
(b) Install the screw.
12. INSTALL AIR CONDITIONING HARNESS ASSEMBLY
(a) Engage each clamp. |
![]() |
(b) Connect each connector to install the air conditioning harness assembly.
13. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY
Click here ![]()
14. INSTALL BLOWER ASSEMBLY
Click here ![]()
15. INSTALL ASPIRATOR
Click here ![]()
16. INSTALL NO. 2 AIR DUCT
Click here ![]()
17. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
Click here ![]()
18. INSTALL NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/ReplacedReplaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Steering sensor |
Steering angle zero point learning (Initialize intelligent clearance sonar system) |
|
|
|
Parking Assist Monitor System |
|
|
Steering angle zero point learning (Initialize panoramic view monitor system) |
Panoramic View Monitor System |
|
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
Make sure to select face mode before disconnecting the cable from the negative (-) battery terminal.
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
Click here ![]()
3. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
Click here ![]()
4. REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY
Click here ![]()
5. DISCONNECT OUTLET HEATER WATER HOSE
(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the outlet heater water hose. NOTICE:
|
![]() |
6. DISCONNECT INLET HEATER WATER HOSE
(a) Using pliers, grip the claws of the clip and slide the clip to disconnect the inlet heater water hose. NOTICE:
|
![]() |
7. DISCONNECT NO. 2 AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
(a) Remove the bolt and rotate the hook connector as shown in the illustration. |
![]() |
(b) Disconnect the No. 2 air conditioning tube and accessory assembly. |
![]() |
(c) Remove the 2 O-rings from the No. 2 air conditioning tube and accessory assembly.
NOTICE:
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
8. REMOVE FRONT SEAT ASSEMBLY LH
Click here ![]()
9. REMOVE FRONT SEAT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY
Click here ![]()
11. REMOVE STEERING COLUMN ASSEMBLY
for Manual Tilt and Manual Telescopic Steering Column:
Click here ![]()
for Power Tilt and Power Telescopic Steering Column:
Click here ![]()
12. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Click here ![]()
13. REMOVE ECU INTEGRATION BOX RH
Click here ![]()
14. REMOVE STEREO COMPONENT EQUALIZER ASSEMBLY (w/ Active Noise Control System)
Click here ![]()
15. REMOVE DCM (TELEMATICS TRANSCEIVER) WITH BRACKET
Click here ![]()
16. REMOVE NO. 1 CLEARANCE WARNING BUZZER (w/ Intelligent Parking Assist System)
Click here ![]()
17. REMOVE DRIVING SUPPORT ECU ASSEMBLY
Click here ![]()
18. REMOVE COOLER (ROOM TEMP. SENSOR) THERMISTOR
Click here ![]()
19. REMOVE ACCELERATOR PEDAL PAD
Click here ![]()
20. REMOVE ACCELERATOR PEDAL
Click here ![]()
21. REMOVE REAR NO. 2 AIR DUCT
Click here ![]()
22. REMOVE REAR NO. 1 AIR DUCT
Click here ![]()
23. REMOVE REAR NO. 4 AIR DUCT
Click here ![]()
24. REMOVE REAR NO. 3 AIR DUCT
Click here ![]()
25. REMOVE FLOOR CARPET BRACKET RH
Click here ![]()
26. REMOVE FLOOR CARPET BRACKET LH
Click here ![]()
27. REMOVE NO. 1 CONSOLE BOX DUCT
Click here ![]()
28. REMOVE NO. 3 DASH PANEL INSULATOR PAD
Click here ![]()
29. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
(a) Remove the bolt and disconnect the earth wire. |
|
(b) Disengage each clamp.
(c) Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
![]() |
Bolt |
![]() |
Screw |
![]() |
Nut |
30. REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Click here ![]()
31. REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Click here ![]()
32. REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU
Click here ![]()
33. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
NOTICE:
- Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
- When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
(a) Disconnect the connector.
*a |
Earth Wire |
*b |
Connector Holder |
![]() |
Connector |
![]() |
Bolt |
![]() |
Nut |
- |
- |
(b) Remove the 3 bolts and disconnect the 3 earth wires.
(c) Remove the 2 nuts and disconnect the connector holder.
(d) Disengage each clamp.
(e) Push down the part (A) in the direction indicated by the arrow (1), to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connector.
![]() |
Release (1) |
![]() |
Move in this Direction (2) |
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(f) Disconnect the connector.
(g) Disengage each clamp to separate the instrument panel wire.
(h) Turn back the front floor mat as shown in the illustration. |
![]() |
(i) Disconnect the drain cooler hose. NOTICE: If the drain cooler hose is disconnected from the cooler unit drain hose grommet, make sure to replace the cooler unit drain hose grommet with a new one. Failure to do so may lead to water ingress. |
|
(j) Remove the cooler unit drain hose grommet. |
![]() |
(k) Remove the 2 hole plugs. |
![]() |
(l) Remove the 3 bolts. |
![]() |
(m) Remove the 4 bolts (A).
![]() |
Bolt (A) |
![]() |
Bolt (B) |
![]() |
Nut |
- |
- |
(n) Remove the bolt (B) and disconnect the brake pedal assembly.
(o) Remove the nut.
(p) Disengage each clamp.
![]() |
Remove in this Direction |
- |
- |
(q) Disconnect each connector.
(r) Remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
34. REMOVE AIR CONDITIONER UNIT ASSEMBLY
Click here ![]()

































