Runnable Signal Malfunction (B2286,P0335). Engine Starter Communication Malfunction (B2779). Open / Short in Steering Lock ECU (B2781)
Runnable Signal Malfunction (B2286,P0335)
DESCRIPTION
These DTCs are stored when the engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2286 |
Runnable Signal Malfunction |
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match. (1-trip detection logic*) |
|
|
P0335 |
Crankshaft Position Sensor Circuit Malfunction (NE Signal) |
The engine speed signal sent by the ECM via direct line and the engine speed signal sent via CAN communication do not match. (1-trip detection logic*) |
|
|
- *: Only detected while a malfunction is present and the engine switch is on (IG).
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
|
|
DTC No. | Data List and Active Test |
|---|---|
B2286 P0335 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Inspect the fuses of circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
PROCEDURE
READ VALUE USING TECHSTREAM (ENGINE CONDITION / ENGINE SPEED)
(a) Connect the Techstream to the DLC3.
(b) Turn the Engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Power Source Control or Starting Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Engine Condition |
Engine state |
Stop or Run |
Stop: Engine stopped Run: Engine running |
- |
Engine Condition
Body Electrical > Starting Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Engine Speed |
Engine speed |
0 to 16383 rpm |
Fluctuates in accordance with actual engine speed |
- |
Engine Speed
OK:
The Techstream display changes correctly in response to the engine condition.
| OK | REPLACE ECM |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
(a) Disconnect the A10 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the A18 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A10-16 (NE) - A18-30 (NEO) |
Always |
Below 1 Ω |
A10-16 (NE) or A18-30 (NEO) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Connect the A10 certification ECU (smart key ECU assembly) connector.
(b) Connect the A18 ECM connector.
(c) Using an oscilloscope, check the engine speed input signal waveform at the terminal of the certification ECU (smart key ECU assembly). OK:
|
|
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE ECM |
Engine Starter Communication Malfunction (B2779)
DESCRIPTION
If the remote engine start ECU does not respond to the certification ECU (smart key ECU assembly) or the remote engine start ID is not registered, this DTC is stored.
HINT:
Registration status of the remote engine start ECU ID can be checked using the "Wireless C Code" item in the Data List.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2779 |
Engine Starter Communication Malfunction |
One of the following conditions is met (1 trip detection logic*):
|
|
DTC output confirmation operation:
|
*: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction DetectedVehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
Engine does not start with remote start operation |
Engine cannot be started by remote start operation only |
DTC No. | Data List and Active Test |
|---|---|
B2779 |
Smart Key
|
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- Before performing the inspection, check that DTC B1242 (wireless door lock control system) is not output.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK CAN COMMUNICATION SYSTEM
(a) Check for CAN communication system DTCs.
Click here ![]()
OK:
CAN communication DTCs are not output.
| NG | GO TO CAN COMMUNICATION SYSTEM (DIAGNOSTIC TROUBLE CODE CHART) |
|
READ VALUE USING TECHSTREAM (WIRELESS C CODE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Wireless C Code |
Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) |
No Regd or Regd |
No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly) Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
|
Wireless C Code
Result | Proceed to |
|---|---|
"No Regd" is displayed on the Techstream |
A |
"Regd" is displayed on the Techstream |
B |
| B | REPLACE REMOTE ENGINE START ECU |
|
REGISTER REMOTE ENGINE STARTER ID
(a) Register the remote engine starter ID.
|
READ VALUE USING TECHSTREAM (WIRELESS C CODE)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Wireless C Code |
Registration status between remote engine start ECU and certification ECU (smart key ECU assembly) |
No Regd or Regd |
No Regd: Remote starter ID not registered to remote engine start ECU and certification ECU (smart key ECU assembly) Regd: Remote starter ID registered to remote engine start ECU and certification ECU (smart key ECU assembly) |
Problems may be caused by the following:
|
Wireless C Code
Result | Proceed to |
|---|---|
"No Regd" is displayed on the Techstream |
A |
"Regd" is displayed on the Techstream |
B |
| A | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| B | REPLACE REMOTE ENGINE START ECU |
Open / Short in Steering Lock ECU (B2781)
DESCRIPTION
The steering lock ECU and steering lock motor are built into the steering lock actuator or upper bracket assembly.
The steering lock ECU (steering lock actuator or upper bracket assembly) detects whether the steering lock is in the lock or unlock position by using the lock sensor and unlock sensor of the steering lock motor.
The steering lock ECU (steering lock actuator or upper bracket assembly) receives lock and unlock request signals from the certification ECU (smart key ECU assembly) and responds with lock and unlock operation signals.
HINT:
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2781 |
Open / Short in Steering Lock ECU |
One of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)):
|
|
DTC Output Confirmation Operation: No confirmation operation is necessary (monitoring is continuous). |
Vehicle Condition and Fail-safe Function when Malfunction Detected Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The steering cannot be locked or unlocked. For this reason, the engine cannot be started. |
Prohibits the engine from being started (the engine does not crank). |
DTC No. | Data List and Active Test |
|---|---|
B2781 |
Smart Key
|
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly), refer to Registration.
Click here

- After performing repairs, confirm that no DTCs are output again.
Click here

HINT:
When all the ECUs that are connected via LIN communication cannot communicate with the certification ECU (smart key ECU assembly), DTC B2785 is stored.
PROCEDURE
CHECK DTC
(a) Using the Techstream, check if LIN communication DTC B2785 is output.
Body Electrical > Smart Key > Trouble CodesHINT:
If a LIN communication DTC is output, perform troubleshooting for the LIN communication system.
Click here ![]()
Result | Proceed to |
|---|---|
DTC B2785 is output. |
A |
DTC B2785 is not output. |
B |
| A | GO TO LIN COMMUNICATION SYSTEM (DTC B2785) |
| B | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
