Lost Communication with ECM / PCM (U0100,U0140,U0142,U0155). Unable to Unlock Steering Wheel (Engine cannot Start)
Lost Communication with ECM / PCM (U0100,U0140,U0142,U0155)
DESCRIPTION
These DTCs are stored when there is a CAN communication malfunction between the certification ECU (smart key ECU assembly), ECM, main body ECU (multiplex network body ECU) or combination meter assembly, and data from the option connector (bus buffer ECU) cannot be received.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
U0100 |
Lost Communication with ECM / PCM |
CAN communication malfunction between certification ECU (smart key ECU assembly) and ECM (1-trip detection logic*) |
ECM |
|
U0140 |
Lost Communication with Main Body ECU |
CAN communication malfunction between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) |
Main body ECU (multiplex network body ECU) |
|
U0142 |
Lost Communication with Main Body ECU |
CAN communication malfunction between certification ECU (smart key ECU assembly) and main body ECU (multiplex network body ECU) (1-trip detection logic*) |
Main body ECU (multiplex network body ECU) |
|
U0155 |
Lost Communication with Combination Meter |
CAN communication malfunction between certification ECU (smart key ECU assembly) and combination meter assembly (1-trip detection logic*) |
Combination meter assembly |
|
- *: Only detected while a malfunction is present.
DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
U0100 |
There is no effect on vehicle behavior. |
If the following conditions are met, it can be determined that the malfunction is not in the direct line (NE) but in the CAN communication system.
If the following conditions are met, it can be determined that there is a malfunction in both the CAN communication system and the direct line (NE).
|
U0140 U0142 |
|
- |
U0155 |
The warning (meter buzzer) does not sound and no warning messages displayed on the multi-information display. |
- |
DTC No. | Data List and Active Test |
|---|---|
U0100 U0140 U0142 U0155 |
- |
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
PROCEDURE
CHECK FOR DTC
(a) Check for DTCs and note any DTCs that are output.
Click here ![]()
| NEXT | GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
Unable to Unlock Steering Wheel (Engine cannot Start)
DESCRIPTION
The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of the steering column. In this case, if the engine switch is turned on (IG) while shaking the steering wheel, as is done for a vehicle with a mechanical key, the lock bar will be unlocked. If the certification ECU (smart key ECU assembly) or ECM is replaced, the system needs to be initialized. Otherwise, the steering cannot be unlocked and the engine cannot be started.
Related Data List and Active Test ItemsProblem Symptom | Data List Item | Active Test Item |
|---|---|---|
Unable to unlock steering wheel (Engine cannot start) |
Smart Key
|
- |
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- Perform either of the following operations to lock/unlock the steering:
- To unlock the steering, carry the key and turn the engine switch on (ACC) or on (IG).
- To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- After performing repairs, confirm that the problem does not recur.
- Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Registration.
Click here

- When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.
Click here

- If the steering lock ECU (steering lock actuator or upper bracket assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the engine. This function prevents the engine from starting while the steering is locked. If the steering is locked for any reason, open and close a door with the engine switch off, and then unlock the steering by pressing the engine switch.
PROCEDURE
CHECK ENGINE SWITCH (SWITCH CONDITION)
(a) Check the power source mode change.
(1) When the key is inside the vehicle and the shift lever is in P, check that pressing the engine switch with the brake pedal released causes the power source mode to change as follows:
OK:
Off → On (ACC) → On (IG) → Off
| NG | GO TO OTHER PROBLEM |
|
CHECK INDICATOR
(a) With the engine switch on (IG), check that Steering Lock active is displayed on the multi-information display in the combination meter assembly.
Result | Proceed to |
|---|---|
Steering Lock active is displayed |
A |
Steering Lock active is not displayed |
B |
| B | GO TO STEP 4 |
|
CHECK STEERING UNLOCK
(a) Turn the steering wheel left and right, and then press the engine switch.
(b) Check that the steering is unlocked.
Result | Proceed to |
|---|---|
The steering is unlocked |
A |
The steering is not unlocked |
B |
| A | USE SIMULATION METHOD TO CHECK |
|
CHECK FOR DTC
(a) Using the Techstream, check if the certification ECU (smart key ECU assembly) DTC is output.
Body Electrical > Smart Key > Trouble CodesResult | Proceed to |
|---|---|
DTCs are not output. |
A |
DTCs are output. |
B |
| B | GO TO DIAGNOSTIC PROCEDURE INDICATED BY OUTPUT DTC |
|
READ VALUE USING TECHSTREAM (UNLOCK REQUEST RECEIVE)
(a) Use the Data List to check if the steering lock request is functioning properly.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Unlock Request Receive |
Status of steering unlock command from certification ECU (smart key ECU assembly) |
OK or NG |
OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed) NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed) |
|
Unlock Request Receive
OK:
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| NG | GO TO STEP 11 |
|
READ VALUE USING TECHSTREAM (L CODE CHECK)
(a) Use the Data List to check if L code certification is functioning properly.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
L Code Check |
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) |
OK or NG |
OK: Verification result normal NG: Verification result abnormal |
When NG is displayed:
|
L Code Check
OK:
OK is displayed on the Techstream.
HINT:
Reasons for verification failure:
- The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
- There is a problem with the communication between ECUs.
- An ECU is replaced, but is not registered.
- An ECU is replaced with an ECU which has a code already stored in it.
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE AND GROUND)
(a) Measure the resistance and voltage according to the value(s) in the table below. Standard Resistance:
NOTICE: If the result is not as specified, check for looseness in the ground cable connection. Standard Voltage:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Connect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Move the shift lever to P and turn the engine switch off.
(c) Check the signal waveform according to the condition(s) in the table below.
*a |
Component with harness connected (Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
*b |
Steering lock motor not operating |
*c |
Steering lock motor operating |
*d |
Waveform |
OK:
Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
G43-3 (IGE) - G43-1 (GND) |
2 V/DIV., 200 ms./DIV. |
Steering lock motor not operating → Operating → Not operating |
Pulse generation (See waveform) |
HINT:
- When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
- In order to take measurements when the lock motor is operating, perform either of the following operations:
- To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).
- To lock the steering, turn the engine switch off with the shift lever in P, and then open a door.
| OK | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G43-3 (IGE) - G40-25 (SLR+) |
Always |
Below 1 Ω |
G43-3 (IGE) or G40-25 (SLR+) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Connect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Connect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| NG | GO TO STEP 13 |
|
READ VALUE USING TECHSTREAM (STEERING UNLOCK)
(a) Check that the steering is locked.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Steering Unlock |
Steering lock ECU (steering lock actuator or upper bracket assembly) unlock confirmation status |
Unset or Set |
Unset: Unlock not confirmed Set: Unlock confirmed |
When Unset is displayed, the steering is not unlocked (the engine cannot be started). |
Steering Unlock
OK:
Set is displayed on the Techstream.
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G43-4 (SLP1) - G40-14 (SLP) |
Always |
Below 1 Ω |
G43-4 (SLP1) or G40-14 (SLP) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
READ VALUE USING TECHSTREAM (UNLOCK REQUEST RECEIVE)
(a) Replace the steering lock ECU (steering lock actuator or upper bracket assembly) with a new one.
for Manual Tilt and Manual Telescopic Steering Column: Click here ![]()
for Power Tilt and Power Telescopic Steering Column: Click here ![]()
(b) Perform registration.
Click here ![]()
(c) Turn the engine switch on (IG).
(d) Use the Data List to check if the steering lock request is functioning properly.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Unlock Request Receive |
Status of steering unlock command from certification ECU (smart key ECU assembly) |
OK or NG |
OK: Certification ECU (smart key ECU assembly) sends steering unlock command (within 10 seconds of engine switch turned on (ACC) or on (IG), or of engine start operation performed) NG: Certification ECU (smart key ECU assembly) does not send steering unlock command (engine switch not turned on (ACC) or on (IG), and engine start operation not performed) |
|
Unlock Request Receive
OK:
Within 10 seconds of turning the engine switch on (ACC) or on (IG) or starting the engine, the Data List item changes to "OK".
| OK | END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE) |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |


