Security Indicator Light Does not Blink. Steering Lock does not Lock. System Diagram
Security Indicator Light Does not Blink
DESCRIPTION
- The certification ECU (smart key ECU assembly) blinks the security indicator light (radio and display receiver assembly) when the immobiliser is set (power switch off).
- The certification ECU (smart key ECU assembly) receives the security indicator light signal from the main body ECU (multiplex network body ECU) via CAN communication when the theft deterrent system is in the arming preparation state or alarm sounding state. Then, the certification ECU (smart key ECU assembly) blinks the security indicator light (radio and display receiver assembly).
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Registration.
Click here

PROCEDURE
CHECK FOR DTC
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble Codes Powertrain > Hybrid Control > Trouble CodesOK:
DTCs are not output.
| NG | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
PERFORM ACTIVE TEST USING TECHSTREAM (IMMOBILISER INDICATOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Smart Key > Active TestTester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
Immobiliser Indicator |
Security indicator light |
OFF/ON |
- |
Immobiliser Indicator
OK:
The security indicator light (radio and display receiver assembly) operates normally.
| NG | GO TO STEP 4 |
|
CHECK SECURITY INDICATOR LIGHT (RADIO AND DISPLAY RECEIVER ASSEMBLY) OPERATION
(a) When the immobiliser is set, check that the security indicator light (radio and display receiver assembly) blinks.*1
OK:
The security indicator light (radio and display receiver assembly) blinks normally.
(b) When the theft deterrent system is in the arming preparation state, check that the security indicator light (radio and display receiver assembly) illuminates.*2
OK:
The security indicator light (radio and display receiver assembly) illuminates normally.
Result | Proceed to |
|---|---|
*1 is NG (*2 is OK) |
A |
*2 is NG (*1 is OK) |
B |
| A | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| B | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SECURITY INDICATOR LIGHT (RADIO AND DISPLAY RECEIVER ASSEMBLY) AND BODY GROUND)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G20 security indicator light (radio and display receiver assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-20 (IND) - G20-16 (LP) |
Always |
Below 1 Ω |
G40-20 (IND) or G20-16 (LP) - Other terminals and body ground |
Always |
10 kΩ or higher |
G20-6 (GND) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Connect the G40 certification ECU (smart key ECU assembly) connector.
(b) Connect the G20 security indicator light (radio and display receiver assembly) connector.
(c) Using an oscilloscope, check the waveform.
*a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
- |
- |
Measurement Condition:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-20 (IND) - Body ground |
Power switch off → on (IG) |
Pulse generation → Below 2 V |
| OK | REPLACE SECURITY INDICATOR LIGHT (RADIO AND DISPLAY RECEIVER ASSEMBLY) |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Steering Lock does not Lock
DESCRIPTION
The steering lock actuator or upper bracket assembly activates the steering lock motor and moves the lock bar into the steering column to lock the steering.
When the steering lock is operating, the steering may not lock when the lock bar is not aligned with the lock hole of the steering column. In this case, the steering can be locked by turning the steering wheel a little, as is done for a vehicle with a mechanical key, to change the position of the lock hole.
Related Data List and Active Test ItemsProblem Symptom | Data List Item | Active Test Item |
|---|---|---|
Steering Lock does not Lock |
Smart Key
|
- |
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- Perform either of the following operations to lock/unlock the steering:
- To unlock the steering, carry the electrical key transmitter sub-assembly and turn the power switch on (ACC) or on (IG).
- To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
- Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
Click here

- The smart key system (for Start Function, HV Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, HV Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After performing repairs, confirm that the problem does not recur.
- Inspect the fuses for circuits related to this system before performing the following procedure.
- When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.
Click here

PROCEDURE
READ VALUE USING TECHSTREAM (LOCK REQUEST RECEIVE)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Lock Request Receive |
Status of steering lock command from certification ECU (smart key ECU assembly) |
OK or NG |
OK: Certification ECU (smart key ECU assembly) sends steering lock command (within 10 seconds of any door opened with shift lever in P and power switch off) NG: Certification ECU (smart key ECU assembly) does not send steering lock command (no door opened with shift lever in P and power switch off) |
If OK is not displayed even though the steering lock conditions are met, the certification ECU (smart key ECU assembly) may be malfunctioning. |
Lock Request Receive
OK:
The certification ECU (smart key ECU assembly) receives a lock request signal within 10 seconds of turning the power switch from on (IG) to on (ACC) or off and opening a door with the shift lever in P, and OK is displayed on the Techstream screen.
| NG | GO TO STEP 7 |
|
READ VALUE USING TECHSTREAM (L CODE CHECK)
(a) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
L Code Check |
Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) |
OK or NG |
OK: Verification result normal NG: Verification result abnormal |
When NG is displayed:
|
L Code Check
OK:
OK is displayed on the Techstream.
HINT:
Reasons for verification failure:
- The steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly) is malfunctioning.
- There is a problem with the communication between ECUs.
- An ECU is replaced, but is not registered.
- An ECU is replaced with an ECU which has a code already stored in it.
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE)
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Measure the resistance and voltage according to the value(s) in the table below. Standard Resistance:
NOTICE: If the result is not as specified, check for looseness in the ground cable connection. Standard Voltage:
|
|
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Connect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Move the shift lever to P and turn the power switch off.
(c) Check the signal waveform according to the condition(s) in the table below.
*a |
Component with harness connected (Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
*b |
Steering lock motor not operating |
*c |
Steering lock motor operating |
*d |
Waveform |
OK:
Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
G43-3 (IGE) - G43-1 (GND) |
2 V/DIV., 200 ms./DIV. |
Steering lock motor not operating → Operating → Not operating |
Pulse generation (See waveform) |
HINT:
- When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
- In order to take measurements when the lock motor is operating, perform either of the following operations:
- To unlock the steering, carry the electrical key transmitter sub-assembly and turn the power switch on (ACC) or on (IG).
- To lock the steering, turn the power switch off with the shift lever in P, and then open a door.
| OK | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G43-3 (IGE) - G40-25 (SLR+) |
Always |
Below 1 Ω |
G43-3 (IGE) or G40-25 (SLR+) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Connect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Connect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
READ VALUE USING TECHSTREAM (FL DOOR COURTESY SW)
(a) Using the Techstream, check the following main body ECU (multiplex network body ECU) Data List item by opening and closing the driver door to confirm the state of the front door courtesy light switch assembly.
Body Electrical > Main Body > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
FL Door Courtesy SW |
Front door LH courtesy light switch signal |
OFF or ON |
OFF: Front door LH closed ON: Front door LH open |
- |
FL Door Courtesy SW
OK:
The Data List item changes in accordance with the opening and closing of the driver door.
| NG | GO TO LIGHTING SYSTEM (Front Door Courtesy Switch Circuit) |
|
READ VALUE USING TECHSTREAM (SHIFT P SIGNAL)
(a) Move the shift lever to P.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Shift P Signal |
Shift position P |
OFF or ON |
OFF: Shift lever not in P ON: Shift lever in P |
Use this item to determine whether the shift lever position switch (P) is malfunctioning. |
Shift P Signal
OK:
ON is displayed on the Techstream.
| NG | GO TO OTHER PROBLEM |
|
READ VALUE USING TECHSTREAM (STEERING LOCK)
(a) Check that the steering is unlocked.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Steering Lock |
Steering lock ECU (steering lock actuator or upper bracket assembly) lock confirmation status |
Unset or Set |
Unset: Lock not confirmed Set: Lock confirmed |
When Unset is displayed, the steering is not locked. |
Steering Lock
OK:
Set is displayed on the Techstream.
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
System Diagram
SYSTEM DIAGRAM
SMART KEY SYSTEM (for Start Function, HV Model)
SMART KEY SYSTEM (for Entry Function, HV Model)
See pageXXX

