Combination Meter
Components
COMPONENTS
ILLUSTRATION
*1 |
CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
*2 |
CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL |
*3 |
CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL |
*4 |
CONSOLE BOX BEZEL |
*5 |
CONSOLE BOX POCKET SUB-ASSEMBLY |
*6 |
FRONT CONSOLE UPPER PANEL GARNISH |
*7 |
LOWER INSTRUMENT PANEL FINISH PANEL LH |
*8 |
LOWER INSTRUMENT PANEL FINISH PANEL RH |
*9 |
LOWER INSTRUMENT PANEL SUB-ASSEMBLY |
*10 |
RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET |
*11 |
REAR UPPER CONSOLE PANEL SUB-ASSEMBLY |
*12 |
SHIFT LEVER KNOB SUB-ASSEMBLY |
ILLUSTRATION
*1 |
COMBINATION METER ASSEMBLY |
*2 |
COMBINATION METER GLASS |
*3 |
INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY |
*4 |
INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY |
*5 |
LOWER CENTER INSTRUMENT PANEL FINISH PANEL |
*6 |
LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY |
*7 |
LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL |
*8 |
NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY |
Disassembly
DISASSEMBLY
NOTICE:
- When removing and installing the combination meter glass, make sure not to touch the display panel.
- Do not allow any dirt, fingerprints, grease, etc., to adhere to the combination meter glass. If the glass is dirty, wipe it clean with a soft cloth.
PROCEDURE
1. REMOVE COMBINATION METER GLASS
(a) Disengage the 8 claws to remove the combination meter glass. |
![]() |
Installation
INSTALLATION
PROCEDURE
1. INSTALL COMBINATION METER ASSEMBLY
(a) Connect the 2 connectors.
(b) Engage the clamp.
(c) Engage the 2 clips as shown in the illustration.
![]() |
Install in this Direction |
(d) Install the combination meter assembly with the 3 screws.
2. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
3. INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here ![]()
4. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here ![]()
5. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Click here ![]()
6. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here ![]()
7. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Click here ![]()
8. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Click here ![]()
9. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here ![]()
10. INSTALL CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
11. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
12. INSTALL CONSOLE BOX BEZEL
Click here ![]()
13. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here ![]()
14. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Click here ![]()
15. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
16. INSTALL CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
17. INSTALL FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
20. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here ![]()
21. CUSTOMIZE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM (for Power Tilt and Power Telescopic Steering Column)
Click here ![]()
Reassembly
REASSEMBLY
NOTICE:
- When removing and installing the combination meter glass, make sure not to touch the display panel.
- Do not allow any dirt, fingerprints, grease, etc., to adhere to the combination meter glass. If the glass is dirty, wipe it clean with a soft cloth.
PROCEDURE
1. INSTALL COMBINATION METER GLASS
(a) Engage the 8 claws to install the combination meter glass. |
![]() |
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during combination meter assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative (-) auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)
Click here ![]()
3. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY
Click here ![]()
4. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH
Click here ![]()
5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL RH
Click here ![]()
6. REMOVE FRONT CONSOLE UPPER PANEL GARNISH
Click here ![]()
7. REMOVE CONSOLE BOX POCKET SUB-ASSEMBLY
Click here ![]()
8. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
9. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Click here ![]()
10. REMOVE REAR UPPER CONSOLE PANEL SUB-ASSEMBLY
Click here ![]()
11. REMOVE CONSOLE BOX BEZEL
Click here ![]()
12. REMOVE CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
13. REMOVE CENTER NO. 2 INSTRUMENT CLUSTER FINISH PANEL
Click here ![]()
14. REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET
Click here ![]()
15. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Click here ![]()
16. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL
Click here ![]()
17. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here ![]()
18. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Click here ![]()
19. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Click here ![]()
20. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Click here ![]()
21. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Click here ![]()
22. REMOVE COMBINATION METER ASSEMBLY
(a) Remove the 3 screws. |
![]() |
(b) Disengage the 2 clips as shown in the illustration.
![]() |
Remove in this Direction |
(c) Disengage the clamp. |
![]() |
(d) Disconnect the 2 connectors to remove the combination meter assembly.






