Odo/Trip Switch Malfunction. On-vehicle Inspection. Operating Light Control Rheostat does not Change Light Brightness
Odo/Trip Switch Malfunction
DESCRIPTION
In this circuit, the combination meter assembly detects ODO/TRIP switch (trip switch) signals via a direct line.
WIRING DIAGRAM
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
READ VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
ODO/TRIP Change Switch |
ODO/TRIP switch (Trip switch) |
OFF or ON |
OFF: Switch released ON: Switch pushed |
- |
ODO/TRIP Change Switch
OK:
ODO/TRIP switch (trip switch) condition displayed on the Techstream changes with the actual switch operation.
| OK | REPLACE COMBINATION METER ASSEMBLY |
|
INSPECT TRIP SWITCH
(a) Remove the trip switch.
Click here ![]()
(b) Inspect the trip switch.
Click here ![]()
| NG | REPLACE TRIP SWITCH |
|
CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)
(a) Disconnect the G15 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G80-3 (A/B) - G15-1 (ODO) |
Always |
Below 1 Ω |
G80-1 (E) - G15-5 (SW3) |
Always |
Below 1 Ω |
G80-3 (A/B) or G15-1 (ODO) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE COMBINATION METER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT COMBINATION METER ASSEMBLY
(a) Inspect speedometer operation
NOTICE:
- The combination meter assembly receives the vehicle speed signal from the skid control ECU (brake booster with master cylinder assembly) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the skid control ECU (brake booster with master cylinder assembly) because it is the source of the vehicle speed signal.
- Data List values of the skid control ECU (brake booster with master cylinder assembly) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
- If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.
(1) Warm up the engine.
(2) Connect the Techstream to the DLC3.
(3) Turn the power switch on (IG).
(4) Turn the Techstream on.
(5) Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
(6) Read the Data List according to the display on the Techstream.
Reference mphTechstream Indication (mph) | Acceptable Range (mph) |
|---|---|
20 |
19.2 to 21.7 |
40 |
39.4 to 42.2 |
60 |
59.8 to 62.6 |
80 |
80.0 to 83.2 |
100 |
100.5 to 103.7 |
120 |
120.9 to 124.1 |
140 |
141.3 to 144.5 |
OK:
Speedometer reading is within the acceptable range at each vehicle speed.
Chassis > ABS/VSC/TRAC > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Vehicle Speed |
Maximum wheel speed sensor |
Min.: 0 km/h, Max.: 326 km/h |
Vehicle stopped: 0 km/h |
When driving at constant speed: No large fluctuations |
Vehicle Speed
(b) Check LED illumination (LED check)
(1) Check the illumination function of the warning or indicator lights listed below when turning the power switch on (IG).
OK:
Warning or Indicator Light | Specified Condition |
|---|---|
Brake warning light / red (malfunction) |
Warning or indicator light comes on for about 3 seconds after turning the power switch on (IG). |
Slip indicator light |
|
VSC OFF indicator light |
|
ABS warning light |
|
Tire pressure warning light |
|
Master warning light |
|
ICS OFF indicator light* |
|
Brake warning light / yellow (minor malfunction) |
|
Brake hold standby indicator light |
|
Brake hold operated indicator light |
|
PCS warning light |
|
SRS warning light |
Warning light comes on for about 6 seconds after turning the power switch on (IG). |
EPS warning light |
When the power switch is turned on (IG), warning light (red) illuminates for 2 seconds and then the warning light (yellow) illuminates. |
MIL (Check engine warning light) |
Warning light comes on when the power switch is turned on (IG). |
- *: w/ Intelligent Clearance Sonar System
Operating Light Control Rheostat does not Change Light Brightness
DESCRIPTION
The combination meter assembly receives signals through this circuit to adjust the illumination of the combination meter assembly. The combination meter assembly sets the illumination level based on the user operation of the light control rheostat switch in the trip switch.
WIRING DIAGRAM
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
HINT:
- The illumination level of the combination meter assembly can be adjusted by pressing the light control rheostat switch (trip switch).
- The illumination of the combination meter assembly dims when the taillights are turned on.
- Setting the illumination to maximum brightness cancels the above dimming of the illumination.
PROCEDURE
READ VALUE USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Light Control Switch (UP) |
Light control rheostat up switch (Trip switch) |
OFF or ON |
OFF: Switch released ON: Switch pushed |
- |
Light Control Switch (DOWN) |
Light control rheostat down switch (Trip switch) |
OFF or ON |
OFF: Switch released ON: Switch pushed |
- |
Tester Display |
|---|
Light Control Switch (UP) |
Light Control Switch (DOWN) |
OK:
Light control rheostat up or down switch (trip switch) condition displayed on the Techstream changes with the actual switch operation.
| OK | REPLACE COMBINATION METER ASSEMBLY |
|
INSPECT TRIP SWITCH
(a) Remove the trip switch.
Click here ![]()
(b) Inspect the trip switch.
Click here ![]()
| NG | REPLACE TRIP SWITCH |
|
CHECK HARNESS AND CONNECTOR (TRIP SWITCH - COMBINATION METER ASSEMBLY)
(a) Disconnect the G15 combination meter assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G80-4 (RV) - G15-2 (TR) |
Always |
Below 1 Ω |
G80-1 (E) - G15-5 (SW3) |
Always |
Below 1 Ω |
G80-4 (RV) or G15-2 (TR) - Body ground |
Always |
10 kΩ or higher |
| OK | REPLACE COMBINATION METER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |