Door Control Receiver
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
w/ Seat Heater System |
- |
- |
*1 |
SPARE WHEEL COVER ASSEMBLY |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*C |
w/ Seat Heater System |
- |
- |
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*3 |
REAR SEAT CUSHION ASSEMBLY |
*4 |
REAR SEAT CUSHION LOCK HOOK |
*5 |
REAR SIDE SEATBACK ASSEMBLY RH |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER |
*2 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
*3 |
ROOF SIDE INNER GARNISH RH |
*4 |
ROOF SIDE RAIL GARNISH ASSEMBLY RH |
*5 |
CLIP |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
Installation
INSTALLATION
PROCEDURE
1. INSTALL ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.
- If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(a) Connect the connector.
(b) Engage the 2 guides and install the electrical key and tire pressure warning ECU and receiver with the bolt.
Torque:
8,3 N·m {85 kgf·cm, 73 in·lbf}
2. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
3. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here ![]()
5. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
6. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
7. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
10. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
11. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
12. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
13. REGISTER TRANSMITTER ID
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
14. INSPECT TIRE PRESSURE WARNING SYSTEM
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
15. PERFORM INITIALIZATION
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
16. PERFORM DIAGNOSTIC SYSTEM CHECK
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
17. INSPECT SRS WARNING LIGHT
for Gasoline Model:
Click here ![]()
for HV Model:
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during electrical key and tire pressure warning ECU and receiver removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
Electrical key and tire pressure warning ECU and receiver |
|
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
NOTICE:
When replacing the electrical key and tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
Click here ![]()
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
Electrical key and tire pressure warning ECU and receiver |
|
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
NOTICE:
When replacing the electrical key and tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the Techstream and write them down before removal.
Click here ![]()
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
4. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
11. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
12. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
Click here ![]()
13. REMOVE ELECTRICAL KEY AND TIRE PRESSURE WARNING ECU AND RECEIVER
NOTICE:
- Do not drop, strike or otherwise subject the electrical key and tire pressure warning ECU and receiver to impact.
- If the electrical key and tire pressure warning ECU and receiver is subjected to an impact, replace it with a new one.
(a) Remove the bolt. |
![]() |
(b) Disengage the 2 guides.
(c) Disconnect the connector to remove the electrical key and tire pressure warning ECU and receiver.



