Vehicle Speed Signal Malfunction (B2282,B2283). Brake Signal Malfunction (B2284). Steering Lock Position Signal Circuit Malfunction (B2285)
Vehicle Speed Signal Malfunction (B2282,B2283)
DESCRIPTION
DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2282 |
Vehicle Speed Signal Malfunction |
The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*) |
|
|
B2283 |
Vehicle Speed Sensor Malfunction |
Either of the of the following malfunctions is detected (a vehicle speed sensor malfunction is detected) (1-trip detection logic*):
|
|
DTC Output Confirmation Operation:
|
- *: Only detected while a malfunction is present and the engine switch is on (IG).
DTC Code | Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|---|
B2282 |
|
- |
B2283 |
|
Steering lock motor operation is prohibited. |
DTC No. | Data List and Active Test |
|---|---|
B2282 B2283 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
READ VALUE USING TECHSTREAM (VEHICLE SPEED METER)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Vehicle Speed Meter |
Vehicle speed |
Min.: 0, Max.: 255 |
Almost same as actual vehicle speed (Speedometer tester) |
- |
Vehicle Speed Meter
HINT:
Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the Techstream.
OK:
Vehicle speed displayed on the Techstream is almost the same as the actual vehicle speed measured using a speedometer tester.
| NG | GO TO METER / GAUGE SYSTEM (Speedometer Malfunction) |
|
READ VALUE USING TECHSTREAM (VEHICLE SPEED SIGNAL)
(a) Enter the following menus: Body Electrical / Power Source Control / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Vehicle Speed Signal |
Vehicle being driven or stopped |
Stop or Run |
Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h or more |
- |
Vehicle Speed Signal
OK:
The Techstream display changes correctly in response to the vehicle condition.
| OK | GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY)
(a) Disconnect the G16 combination meter assembly connector.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Disconnect the A18 ECM connector.
(d) Disconnect the G3 radio and display receiver assembly connector.
(e) Disconnect the G9 DCM (telematics transceiver) connector.*1
(f) Disconnect the G8 stereo component amplifier assembly.*2
(g) Disconnect the G13 navigation ECU.*3
- *1: w/ Manual (SOS) Switch
- *2: for 14 Speakers
- *3: w/ Navigation System
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-19 (SPD) - G16-6 (+S) |
Always |
Below 1 Ω |
G40-19 (SPD) or G16-6 (+S) - Other terminals and body ground |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Connect the G40 certification ECU (smart key ECU assembly) connector.
(b) Connect the G16 combination meter assembly connector.
(c) Using an oscilloscope, check the waveform.
*a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
- |
- |
Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
G40-19 (SPD) - G40-18 (E) |
Engine switch on (IG), vehicle being driven at approx. 5 km/h |
5 V/DIV., 20 ms./DIV. |
Pulse generation |
HINT:
The wavelength becomes shorter as the vehicle speed increases.
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | GO TO METER / GAUGE SYSTEM (Speed Signal Circuit) |
Brake Signal Malfunction (B2284)
DESCRIPTION
This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2284 |
Brake Signal Malfunction |
The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*) |
|
|
- *: Only detected while a malfunction is present and the engine switch is on (IG).
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the key indicator display is not displayed on the multi-information display). However, the engine can be started by turning the engine switch on (ACC) and then pressing and holding it.
|
- |
DTC No. | Data List and Active Test |
|---|---|
B2284 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Inspect the fuses of circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
READ VALUE USING TECHSTREAM (STOP LIGHT SWITCH1)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Power Source Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Stop Light Switch1 |
State of brake pedal |
OFF or ON |
OFF: Brake pedal released ON: Brake pedal depressed |
|
Stop Light Switch1
OK:
The Techstream display changes correctly in response to the brake pedal operation.
| OK | GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
(a) Disconnect the K10 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the A33 stop light switch assembly connector.
(c) Disconnect the A18 ECM connector.
(d) Disconnect the A28 skid control ECU (brake actuator assembly) connector.
(e) Disconnect the G21 shift lock control unit assembly connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K10-25 (STP1) - A33-3 (L) |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Connect the K10 certification ECU (smart key ECU assembly) connector.
(b) Connect the A33 stop light switch assembly connector.
(c) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPLACE STOP LIGHT SWITCH ASSEMBLY |
Steering Lock Position Signal Circuit Malfunction (B2285)
DESCRIPTION
This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B2285 |
Steering Lock Position Signal Circuit Malfunction |
The steering lock position signal sent by the steering lock ECU (steering lock actuator or upper bracket assembly) via direct line and the steering lock position signal sent via LIN communication do not match. (1-trip detection logic*1) |
|
|
- *1: Only detected while a malfunction is present and the engine switch is on (IG).
- *2: for Toyota Entune Remote Connect Compatible Type
Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
The engine cannot be started. |
The ECU does not send an engine start request. |
DTC No. | Data List and Active Test |
|---|---|
B2285 |
Power Source Control
|
WIRING DIAGRAM
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
- The smart key system (for Start Function, Gasoline Model) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function, Gasoline Model) after confirming that the communication systems are functioning properly.
Click here

- Inspect the fuses of circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), steering lock ECU (steering lock actuator or upper bracket assembly) or DCM (telematics transceiver)*, refer to Registration.
Click here

- *: for Toyota Entune Remote Connect Compatible Type
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
CHECK FOR DTC
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble CodesHINT:
- If the steering cannot be unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.
- If LIN communication is not available, the steering cannot be locked or unlocked.
OK:
LIN communication system DTC B2785 is not output simultaneously.
| NG | GO TO DTC B2785 |
|
READ VALUE USING TECHSTREAM (STEERING UNLOCK SWITCH)
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Power Source Control / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Steering Unlock Switch |
State of steering unlock sensor signal output from steering lock ECU (steering lock actuator or upper bracket assembly) |
OFF or ON |
OFF: Steering locked ON: Steering unlocked |
|
Steering Unlock Switch
OK:
The Techstream display changes.
| OK | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
HINT:
|
|
||||||||||||
Result | Proceed to |
|---|---|
OK (except Toyota Entune Remote Connect Compatible Type) |
A |
OK (for Toyota Entune Remote Connect Compatible Type) |
B |
NG |
C |
| B | GO TO STEP 5 |
| C | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP) - G43-4 (SLP1) |
Always |
Below 1 Ω |
G40-14 (SLP) or G43-4 (SLP1) - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - DCM)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Disconnect the G9 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP) - G43-4 (SLP1) |
Always |
Below 1 Ω |
G43-4 (SLP1) - G9-29 (SLPD) |
Always |
Below 1 Ω |
G40-14 (SLP), G43-4 (SLP1) or G9-29 (SLPD) - Other terminals and body ground |
Always |
10 kΩ or higher |
(e) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-14 (SLP), G43-4 (SLP1) or G9-29 (SLPD) - Body ground |
Always |
Below 1 V |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Check the push-button start function.
(1) Enter the vehicle while carrying an electrical key transmitter sub-assembly.
(2) Depress the brake pedal with the shift lever in P.
(3) Check that the engine starts when the engine switch is pressed.
Result | Proceed to |
|---|---|
Engine starts |
A |
Engine does not start |
B |
| A | REPLACE DCM (TELEMATICS TRANSCEIVER) |
| B | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |

