Front Evaporator Temperature Sensor
Components
COMPONENTS
ILLUSTRATION
*A |
for A25A-FXS |
- |
- |
*1 |
AIR CONDITIONING HARNESS ASSEMBLY |
*2 |
COOLER EXPANSION VALVE |
*3 |
COOLING UNIT PARTS |
*4 |
HEATER CLAMP |
*5 |
HEATER PIPE GROMMET |
*6 |
HEATER RADIATOR UNIT SUB-ASSEMBLY |
*7 |
NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
*8 |
NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
*9 |
NO. 1 COOLER THERMISTOR |
*10 |
NO. 2 AIR DUCT SUB-ASSEMBLY |
*11 |
NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
*12 |
UPPER HEATER CASE |
*13 |
LOWER HEATER CASE |
*14 |
O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 11 or equivalent |
- |
- |
ILLUSTRATION
*A |
for 2GR-FKS |
- |
- |
*1 |
AIR CONDITIONING HARNESS ASSEMBLY |
*2 |
COOLER EXPANSION VALVE |
*3 |
COOLING UNIT PARTS |
*4 |
HEATER CLAMP |
*5 |
HEATER PIPE GROMMET |
*6 |
HEATER RADIATOR UNIT SUB-ASSEMBLY |
*7 |
NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY |
*8 |
NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY |
*9 |
NO. 1 COOLER THERMISTOR |
*10 |
NO. 2 AIR DUCT SUB-ASSEMBLY |
*11 |
NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY |
*12 |
UPPER HEATER CASE |
*13 |
LOWER HEATER CASE |
*14 |
O-RING |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
![]() |
Compressor oil ND-OIL 12 or equivalent |
- |
- |
Inspection
INSPECTION
PROCEDURE
1. INSPECT NO. 1 COOLER THERMISTOR
(a) Measure the resistance according to the value(s) in the table below.
*a |
Component without harness connected (No. 1 Cooler Thermistor) |
*b |
Sensing Portion |
*c |
Resistance (kΩ) |
*d |
Temperature (°C (°F)) |
*e |
Allowable Range |
- |
- |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
1 - 2 |
-10°C (14°F) |
7.30 to 9.10 kΩ |
-5°C (23°F) |
5.65 to 6.95 kΩ |
|
0 °C |
4.40 to 5.35 kΩ |
|
5 °C |
3.40 to 4.15 kΩ |
|
10 °C |
2.70 to 3.25 kΩ |
|
15 °C |
2.14 to 2.58 kΩ |
|
20 °C |
1.71 to 2.05 kΩ |
|
25 °C |
1.38 to 1.64 kΩ |
|
30 °C |
1.11 to 1.32 kΩ |
If the resistance is not as specified, replace the No. 1 cooler thermistor.
NOTICE:
- Hold the sensor only by its connector. Touching the sensing portion may change the resistance value.
- When measuring, the sensor temperature must be the same as the ambient temperature.
HINT:
As the temperature increases, the resistance decreases (see the graph).
Installation
INSTALLATION
PROCEDURE
1. INSTALL NO. 1 COOLER THERMISTOR
(a) for 2GR-FKS:
(1) Install the No. 1 cooler thermistor as shown in the illustration. Installation Position:
NOTICE:
|
|
(b) for A25A-FXS:
(1) Install the No. 1 cooler thermistor as shown in the illustration. Installation Position:
NOTICE:
|
|
2. INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
for 2GR-FKS:
Click here ![]()
for A25A-FXS:
Click here ![]()
3. INSTALL COOLER EXPANSION VALVE
for 2GR-FKS:
Click here ![]()
for A25A-FXS:
Click here ![]()
4. INSTALL COOLING UNIT PARTS
Click here ![]()
5. INSTALL HEATER RADIATOR UNIT SUB-ASSEMBLY
Click here ![]()
6. INSTALL HEATER CLAMP
Click here ![]()
7. INSTALL HEATER PIPE GROMMET
Click here ![]()
8. INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
9. INSTALL AIR CONDITIONING HARNESS ASSEMBLY
for 2GR-FKS:
Click here ![]()
for A25A-FXS:
Click here ![]()
10. INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY
Click here ![]()
11. INSTALL NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
12. INSTALL BLOWER ASSEMBLY
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 1 cooler thermistor removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Steering sensor |
Steering angle zero point learning (Initialize intelligent clearance sonar system) |
|
|
|
Parking Assist Monitor System |
|
|
Steering angle zero point learning (Initialize panoramic view monitor system) |
Panoramic View Monitor System |
|
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane Departure Alert System (w/ Steering Control) |
|
Pre-collision System |
|||
Intelligent Clearance Sonar System* |
|||
Lighting System (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking Assist Monitor System |
||
Panoramic View Monitor System |
|||
Steering sensor |
Steering angle zero point learning (Initialize intelligent clearance sonar system) |
|
|
|
Parking Assist Monitor System |
|
|
Steering angle zero point learning (Initialize panoramic view monitor system) |
Panoramic View Monitor System |
|
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here ![]()
PROCEDURE
1. REMOVE BLOWER ASSEMBLY
Click here ![]()
2. REMOVE NO. 4 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Click here ![]()
3. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY
Click here ![]()
4. REMOVE AIR CONDITIONING HARNESS ASSEMBLY
for 2GR-FKS:
Click here ![]()
for A25A-FXS:
Click here ![]()
5. REMOVE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY
Click here ![]()
6. REMOVE HEATER PIPE GROMMET
Click here ![]()
7. REMOVE HEATER CLAMP
Click here ![]()
8. REMOVE HEATER RADIATOR UNIT SUB-ASSEMBLY
Click here ![]()
9. REMOVE COOLING UNIT PARTS
Click here ![]()
10. REMOVE COOLER EXPANSION VALVE
Click here ![]()
11. REMOVE NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY
for 2GR-FKS:
Click here ![]()
for A25A-FXS:
Click here ![]()
12. REMOVE NO. 1 COOLER THERMISTOR
(a) for 2GR-FKS:
(1) Remove the No. 1 cooler thermistor. |
![]() |
(b) for A25A-FXS:
(1) Remove the No. 1 cooler thermistor. |
![]() |






