Side Airbag Sensor Assembly No.2 Lost Communication (LH) (B163B,B163C). Front Door Pressure Sensor RH Circuit Range/Performance (B166B,B166C,B166F). Lost Communication with Front Door Pressure Sensor
Side Airbag Sensor Assembly No.2 Lost Communication (LH) (B163B,B163C)
DESCRIPTION
The side collision sensor LH circuit (bus 2) consists of the airbag ECU assembly and side No. 1 airbag sensor LH.
The side No. 1 airbag sensor LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B163B |
Side Airbag Sensor Assembly No.2 Lost Communication (LH) |
|
|
Comes on |
Does not apply to test/check mode |
B163C |
Side Airbag Sensor Assembly No.2 Initialization Error (LH) |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK CONNECTION OF CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the airbag ECU assembly and side No. 1 airbag sensor LH.
OK:
The connectors are properly connected.
| NG | CONNECT CONNECTORS PROPERLY |
|
CHECK CONNECTORS
(a) Disconnect the connectors from the airbag ECU assembly and side No. 1 airbag sensor LH.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG | REPLACE FLOOR WIRE |
|
CHECK FLOOR WIRE
(a) Connect the cable to the negative (-) battery terminal. |
|
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K33-2 (BFL+) - Body ground |
Engine switch on (IG) |
Below 1 V |
K33-1 (BFL-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(d) Turn the engine switch off.
(e) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(f) Using a service wire, connect terminals 29 (BCL+) and 30 (BCL-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K33-2 (BFL+) - K33-1 (BFL-) |
Always |
Below 1 Ω |
(h) Disconnect the service wire from connector B.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K33-2 (BFL+) - K33-1 (BFL-) |
Always |
1 MΩ or higher |
K33-2 (BFL+) - Body ground |
Always |
1 MΩ or higher |
K33-1 (BFL-) - Body ground |
Always |
1 MΩ or higher |
| NG | REPLACE FLOOR WIRE |
|
CHECK SIDE NO. 1 AIRBAG SENSOR LH
(a) Connect the connector to the airbag ECU assembly. |
|
(b) Interchange the side No. 1 airbag sensor LH with RH and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B162B, B162C, B163B and B163C may be output at this time, but they are not related to this check.
Result | Proceed to |
|---|---|
DTC B163B or B163C is output. |
A |
DTC B162B or B162C is output. |
B |
DTCs B162B, B162C, B163B and B163C are not output. |
C |
(i) Turn the engine switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Return the side No. 1 airbag sensor LH and RH to their original positions and connect the connectors.
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | REPLACE SIDE NO. 1 AIRBAG SENSOR LH |
| C | USE SIMULATION METHOD TO CHECK |
Front Door Pressure Sensor RH Circuit Range/Performance (B166B,B166C,B166F)
DESCRIPTION
The side collision sensor RH circuit (bus 1) consists of the airbag ECU assembly, side airbag pressure sensor RH and side No. 2 airbag sensor RH.
The side airbag pressure sensor RH and side No. 2 airbag sensor RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side airbag pressure sensor RH.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B166B |
Front Door Pressure Sensor RH Circuit Range/Performance |
|
|
Comes on |
Does not apply to test/check mode |
B166C |
Front Door Pressure Sensor RH |
|
|
Comes on |
Does not apply to test/check mode |
B166F |
Front Door Pressure Sensor Threshold Malfunction (RH) |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
Click here ![]()
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK SIDE AIRBAG PRESSURE SENSOR RH
(a) Turn the engine switch off. |
|
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminals to disable the SRS system.
(c) Interchange the side airbag pressure sensor RH with LH and connect the connectors.
(d) Connect the cable to the negative (-) battery terminal.
(e) Turn the engine switch on (IG), and wait for at least 60 seconds.
(f) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(g) Turn the engine switch off.
(h) Turn the engine switch on (IG), and wait for at least 60 seconds.
(i) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B166B, B166C, B166F, B167A, B167E and B167F may be output at this time, but they are not related to this check.
Result | Proceed to |
|---|---|
DTC B166B, B166C or B166F is output. |
A |
DTC B167A, B167E or B167F is output. |
B |
DTCs B166B, B166C, B166F, B167A, B167E and B167F are not output. |
C |
(j) Turn the engine switch off.
(k) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(l) Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | REPLACE SIDE AIRBAG PRESSURE SENSOR RH |
| C | USE SIMULATION METHOD TO CHECK |
Lost Communication with Front Door Pressure Sensor RH (B166D,B166E)
DESCRIPTION
The side collision sensor RH circuit (bus 1) consists of the airbag ECU assembly, side airbag pressure sensor RH and side No. 2 airbag sensor RH.
The side airbag pressure sensor RH and side No. 2 airbag sensor RH detect impacts to the vehicle and send signals to the airbag ECU assembly to determine if the airbags and pretensioners should be deployed.
These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Test Mode / Check Mode |
|---|---|---|---|---|---|
B166D |
Lost Communication with Front Door Pressure Sensor RH |
|
|
Comes on |
Does not apply to test/check mode |
B166E |
Front Door Pressure Sensor RH Initialization Incomplete |
|
|
Comes on |
Does not apply to test/check mode |
WIRING DIAGRAM
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here ![]()
PROCEDURE
CHECK CONNECTION OF CONNECTORS
(a) Turn the engine switch off.
(b) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Check that the connectors are properly connected to the side airbag pressure sensor RH and side No. 2 airbag sensor RH. Also check that the connectors that link the floor wire and front door wire RH are properly connected.
OK:
The connectors are properly connected.
| NG | CONNECT CONNECTORS PROPERLY |
|
CHECK CONNECTORS
(a) Disconnect the connectors from the side airbag pressure sensor RH and side No. 2 airbag sensor RH. Also disconnect the connectors that link the floor wire and front door wire RH.
(b) Check that the terminals of the connectors are not deformed or damaged.
OK:
The terminals are not deformed or damaged.
| NG | REPLACE FLOOR WIRE OR FRONT DOOR WIRE RH |
|
CHECK WIRE HARNESS
(a) Connect the connectors that link the floor wire and front door wire RH. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K30-1 (BDR+) - Body ground |
Engine switch on (IG) |
Below 1 V |
K30-2 (BDR-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K30-1 (BDR+) - K30-2 (BDR-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector E.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K30-1 (BDR+) - K30-2 (BDR-) |
Always |
1 MΩ or higher |
K30-1 (BDR+) - Body ground |
Always |
1 MΩ or higher |
K30-2 (BDR-) - Body ground |
Always |
1 MΩ or higher |
| NG | GO TO STEP 5 |
|
CHECK SIDE AIRBAG PRESSURE SENSOR RH
(a) Connect the connector to the side No. 2 airbag sensor RH. |
|
(b) Interchange the side airbag pressure sensor RH with LH and connect the connectors.
(c) Connect the cable to the negative (-) battery terminal.
(d) Turn the engine switch on (IG), and wait for at least 60 seconds.
(e) Clear the DTCs stored in memory.
Body Electrical > SRS Airbag > Clear DTCs(f) Turn the engine switch off.
(g) Turn the engine switch on (IG), and wait for at least 60 seconds.
(h) Check for DTCs.
Body Electrical > SRS Airbag > Trouble CodesHINT:
Codes other than DTCs B166D, B166E, B167B and B167C may be output at this time, but they are not related to this check.
Result | Proceed to |
|---|---|
DTC B166D or B166E is output. |
A |
DTC B167B or B167C is output. |
B |
DTCs B166D, B166E, B167B and B167C are not output. |
C |
(i) Turn the engine switch off.
(j) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(k) Return the side airbag pressure sensor RH and LH to their original positions and connect the connectors.
| A | REPLACE AIRBAG ECU ASSEMBLY |
| B | REPLACE SIDE AIRBAG PRESSURE SENSOR RH |
| C | USE SIMULATION METHOD TO CHECK |
CHECK FLOOR WIRE
(a) Disconnect the floor wire connector from the front door wire RH. |
|
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the engine switch on (IG).
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK1-23 (BDR+) - Body ground |
Engine switch on (IG) |
Below 1 V |
IK1-41 (BDR-) - Body ground |
Engine switch on (IG) |
Below 1 V |
(e) Turn the engine switch off.
(f) Disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(g) Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.
NOTICE:
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
(h) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK1-23 (BDR+) - IK1-41 (BDR-) |
Always |
Below 1 Ω |
(i) Disconnect the service wire from connector B.
(j) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
IK1-23 (BDR+) - IK1-41 (BDR-) |
Always |
1 MΩ or higher |
IK1-23 (BDR+) - Body ground |
Always |
1 MΩ or higher |
IK1-41 (BDR-) - Body ground |
Always |
1 MΩ or higher |
| OK | REPLACE FRONT DOOR WIRE RH |
| NG | REPLACE FLOOR WIRE |





