Child Restraint Seat Tether Anchor
Components
COMPONENTS
ILLUSTRATION
*A |
for HV Model |
- |
- |
*1 |
LUGGAGE TRIM SERVICE HOLE COVER |
- |
- |
ILLUSTRATION
*A |
w/ Seat Heater System |
- |
- |
*1 |
SPARE WHEEL COVER ASSEMBLY |
- |
- |
ILLUSTRATION
*A |
for Gasoline Model |
*B |
for HV Model |
*C |
w/ Seat Heater System |
- |
- |
*1 |
LUGGAGE COMPARTMENT INNER TRIM PAD |
*2 |
REAR CENTER SEAT OUTER BELT ASSEMBLY |
*3 |
REAR SEAT CUSHION ASSEMBLY |
*4 |
REAR SEAT CUSHION LOCK HOOK |
*5 |
REAR SIDE SEATBACK ASSEMBLY LH |
*6 |
REAR SIDE SEATBACK ASSEMBLY RH |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
● |
Non-reusable part |
ILLUSTRATION
*1 |
CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET |
*2 |
PACKAGE TRAY TRIM PANEL ASSEMBLY |
*3 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*4 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
*5 |
REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH |
*6 |
REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH |
*7 |
REAR SEAT SHOULDER BELT COVER |
*8 |
ROOF SIDE INNER GARNISH LH |
*9 |
ROOF SIDE INNER GARNISH RH |
*10 |
ROOF SIDE RAIL GARNISH ASSEMBLY LH |
*11 |
ROOF SIDE RAIL GARNISH ASSEMBLY RH |
*12 |
CLIP |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET
HINT:
Use the same procedure for all child restraint seat tether anchor brackets.
(a) Engage the guide and install the child restraint seat tether anchor bracket with the bolt.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
2. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here ![]()
3. INSTALL REAR SEAT SHOULDER BELT COVER
Click here ![]()
4. INSTALL CENTER STOP LIGHT SET
Click here ![]()
5. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here ![]()
6. CONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7. INSTALL ROOF SIDE INNER GARNISH LH
Click here ![]()
8. INSTALL ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
9. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
10. INSTALL ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
Click here ![]()
13. INSTALL REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
14. INSTALL REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here ![]()
16. INSTALL REAR SEAT CUSHION ASSEMBLY
Click here ![]()
17. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
18. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
19. INSTALL LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
20. INSTALL SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
21. INSTALL LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
22. PERFORM DIAGNOSTIC SYSTEM CHECK
for HV Model:
Click here ![]()
for Gasoline Model:
Click here ![]()
23. INSPECT SRS WARNING LIGHT
for HV Model:
Click here ![]()
for Gasoline Model:
Click here ![]()
Removal
REMOVAL
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during child restraint seat tether anchor bracket removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for Gasoline Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
CAUTION:
- Be sure to read Precaution thoroughly before servicing.
Click here


- Wear protective gloves. Sharp areas on the parts may injure your hands.
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|---|
| *: When performing learning using the Techstream. Click here |
|||
Disconnect cable from negative auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
Pre-collision system |
|||
Intelligent clearance sonar system* |
|||
Lighting system (for HV Model with Cornering Light) |
|||
Memorize steering angle neutral point |
Parking assist monitor system |
||
Panoramic view monitor system |
|||
CAUTION:
- Be sure to read Precaution thoroughly before servicing.
Click here


- Wear protective gloves. Sharp areas on the parts may injure your hands.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here ![]()
2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER (for HV Model)
Click here ![]()
3. REMOVE SPARE WHEEL COVER ASSEMBLY (w/ Seat Heater System)
Click here ![]()
4. REMOVE LUGGAGE COMPARTMENT INNER TRIM PAD (w/ Seat Heater System)
Click here ![]()
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for A25A-FXS:
Click here ![]()
for 2GR-FKS:
Click here ![]()
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here ![]()
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here ![]()
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here ![]()
9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here ![]()
10. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here ![]()
12. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY LH
Click here ![]()
14. REMOVE ROOF SIDE RAIL GARNISH ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here ![]()
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
Click here ![]()
18. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
19. REMOVE CENTER STOP LIGHT SET
Click here ![]()
20. REMOVE REAR SEAT SHOULDER BELT COVER
Click here ![]()
21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here ![]()
22. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR BRACKET
HINT:
Use the same procedure for all child restraint seat tether anchor brackets.
(a) Remove the bolt. |
![]() |
(b) Disengage the guide to remove the child restraint seat tether anchor bracket.


