Active Control Engine Mount(for Front Side)
Components
COMPONENTS
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*1 |
FRONT ENGINE MOUNTING INSULATOR |
*2 |
NO. 1 ENGINE UNDER COVER |
*3 |
REAR ENGINE UNDER COVER LH |
*4 |
V-BANK COVER SUB-ASSEMBLY |
*5 |
VACUUM HOSE |
*6 |
FRONT ENGINE MOUNTING BRACKET |
*7 |
STAY |
*8 |
FRONT WHEEL OPENING EXTENSION PAD LH |
*9 |
FRONT WHEEL OPENING EXTENSION PAD RH |
- |
- |
![]() |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
Installation
INSTALLATION
PROCEDURE
1. INSTALL FRONT ENGINE MOUNTING INSULATOR
(a) Install the stay to the front engine mounting insulator with the nut.
Torque:
6 N·m {61 kgf·cm, 53 in·lbf}
(b) Install the front engine mounting insulator to the front frame assembly with the 3 nuts.
Torque:
72 N·m {734 kgf·cm, 53 ft·lbf}
(c) Install the front engine mounting bracket to the transaxle housing with the 3 bolts. Torque: Bolt (A), (B) and (C) : 42 N·m {428 kgf·cm, 31 ft·lbf} NOTICE: Temporarily tighten the bolt (A), and then fully tighten the 3 bolts in the order of (B), (C) and (A). |
![]() |
(d) Install the front engine mounting bracket to the front engine mounting insulator with the bolt.
Torque:
Bolt (D) :
72 N·m {734 kgf·cm, 53 ft·lbf}
(e) Connect the vacuum hose to the front engine mounting insulator.
(f) Engage the 2 clamps to install the vacuum hoses to the front engine mounting insulator.
2. INSTALL REAR ENGINE UNDER COVER LH
Click here ![]()
3. INSTALL NO. 1 ENGINE UNDER COVER
Click here ![]()
4. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
5. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
6. INSTALL V-BANK COVER SUB-ASSEMBLY
Click here ![]()
7. INSTALL VACUUM SWITCHING VALVE (for Active Control Engine Mount System)
Click here ![]()
On-vehicle Inspection
ON-VEHICLE INSPECTION
HINT:
Refer to Problem Symptoms Table.
Click here ![]()
PROCEDURE
1. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
2. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
3. REMOVE NO. 1 ENGINE UNDER COVER
Click here ![]()
4. REMOVE REAR ENGINE UNDER COVER LH
Click here ![]()
5. INSPECT FRONT ENGINE MOUNTING INSULATOR
(a) Disconnect the vacuum hose from the front engine mounting insulator.
(b) Using a vacuum pump, apply vacuum of 80 kPa (600 mmHg, 23.6 in.Hg) and wait for 1 minute. |
![]() |
(c) Check that there is no change in the needle movement of the vacuum pump gauge.
OK:
Vacuum pressure holds.
(d) Check that there is no fluid leakage caused by a break in the diaphragm.
(e) Connect the vacuum hose to the front engine mounting insulator.
6. INSTALL REAR ENGINE UNDER COVER LH
Click here ![]()
7. INSTALL NO. 1 ENGINE UNDER COVER
Click here ![]()
8. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
9. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
Removal
REMOVAL
PROCEDURE
1. REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)
Click here ![]()
2. REMOVE V-BANK COVER SUB-ASSEMBLY
Click here ![]()
3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
Click here ![]()
4. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
Click here ![]()
5. REMOVE NO. 1 ENGINE UNDER COVER
Click here ![]()
6. REMOVE REAR ENGINE UNDER COVER LH
Click here ![]()
7. REMOVE FRONT ENGINE MOUNTING INSULATOR
(a) Disengage the 2 clamps to separate the vacuum hoses from the front engine mounting insulator. |
![]() |
(b) Disconnect the vacuum hose from the front engine mounting insulator. |
![]() |
(c) Support the engine assembly with transaxle using a jack and wooden block.
![]() |
Wooden Block Placement Location |
(d) Remove the 4 bolts and front engine mounting bracket. |
![]() |
(e) Remove the 3 nuts and front engine mounting insulator from the front frame assembly. |
![]() |
(f) Remove the nut and stay from the front engine mounting insulator. |
![]() |








