PCU Interlock Circuit Open (P1CE213,P1CE292). IGB Signal Circuit Short to Auxiliary Battery (P1CFA12). Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off (P33B99F)
PCU Interlock Circuit Open (P1CE213,P1CE292)
DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects that a safety device (interlock) is operated or that there is an open circuit in the detection circuit. (Even if an open circuit occurs while the vehicle is stopped, the system determines that the safety device was operated.)
The cause of this malfunction may be one of the following:
Detection switch system malfunction- Inverter with converter assembly malfunction
- MG ECU malfunction
- Inverter with converter assembly malfunction
- CAN communication error between the MG ECU and hybrid vehicle control ECU
INSPECTION DESCRIPTION
System Diagram Location | Inspection Content | Reason | Inspection Step |
|---|---|---|---|
*a |
Check whether the safety device (interlock) is connected securely and installed properly (inverter cover, etc.). |
DTC output due to improper connection or forgetting to install parts. |
4 |
*b |
Inspect the detection circuit. |
DTC output due to an open circuit or improper connection (dirt, foreign matter, etc.). |
5 |
DESCRIPTION
Refer to the description for DTC P0A0A13.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P1CE213 |
PCU Interlock Circuit Open |
Interlock signal line opens while the vehicle is being driven (at 5 km/h or more) (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
P1CE292 |
PCU Interlock Performance or Incorrect Operation |
Either of the following conditions is met:
(1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 5 seconds or more.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
CAUTION:
- Before the following operations are conducted, take precautions to prevent electric shock by turning the power switch off, wearing insulated gloves, and removing the service plug grip from HV battery.
- Inspecting the high-voltage system
- Disconnecting the low voltage connector of the inverter with converter assembly
- Disconnecting the low voltage connector of the HV battery
- To prevent electric shock, make sure to remove the service plug grip to cut off the high voltage circuit before servicing the vehicle.

- After removing the service plug grip from the HV battery, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

- After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.
Click here

HINT:
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
*a
Without waiting for 10 minutes
NOTICE:
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
- As interlock circuit DTCs or other DTCs may be stored when the power switch is turned on (IG) in the following procedure, make sure to clear the DTCs after inspection.
PROCEDURE
CHECK DTC OUTPUT (HYBRID CONTROL, MOTOR GENERATOR)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control and Motor Generator / Trouble Codes.
(d) Check for DTCs.
Powertrain > Hybrid Control > Trouble Codes Powertrain > Motor Generator > Trouble CodesResult | Proceed to |
|---|---|
P1CE213 or P1CE292 only is output, or DTCs except the ones in the table below are also output. |
A |
DTCs of hybrid control system in the tables below are output. |
B |
DTCs of motor generator control system in the tables below are output. |
C |
Malfunction Content | System | Relevant DTC |
|
|---|---|---|---|
Microcomputer malfunction |
Hybrid control system |
P060647 |
Hybrid/EV Powertrain Control Module Processor Watchdog / Safety MCU Failure |
P060687 |
Hybrid/EV Powertrain Control Module Processor to Monitoring Processor Missing Message |
||
P060A47 |
Hybrid/EV Powertrain Control Module Monitoring Processor Watchdog / Safety MCU Failure |
||
P060A87 |
Hybrid/EV Powertrain Control Module Processor from Monitoring Processor Missing Message |
||
P060B49 |
Hybrid/EV Powertrain Control Module A/D Processing Internal Electronic Failure |
||
P060B71 |
Hybrid/EV Powertrain Control Module A/D Processing Actuator Stuck |
||
P060B1C |
Hybrid/EV Powertrain Control Module A/D Processing Voltage Out of Range |
||
P1CE349 |
Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Internal Electronic Failure |
||
P1CE371 |
Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Actuator Stuck |
||
P1CE31C |
Hybrid/EV Powertrain Control Module Monitoring Processor A/D Processing Voltage Out of Range |
||
P060A45 |
Hybrid/EV Powertrain Control Module Monitoring Processor Program Memory Failure |
||
P060A44 |
Hybrid/EV Powertrain Control Module Monitoring Processor Data Memory Failure |
||
P060A29 |
Hybrid/EV Powertrain Control Module Monitoring Processor Signal Invalid |
||
P060A49 |
Hybrid/EV Powertrain Control Module Monitoring Processor Internal Electronic Failure |
||
P0A1B49 |
Drive Motor "A" Control Module Internal Electronic Failure |
||
Motor generator control system |
P0A1B1F |
Generator Control Module Circuit Intermittent |
|
Power source circuit malfunction |
Hybrid control system |
P06881F |
ECM/PCM Power Relay Sense Circuit Intermittent |
Communication system malfunction |
Hybrid control system |
P312387 |
Lost Communication with Drive Motor Control Module "A" from Hybrid/EV Control Module Missing Message |
System malfunction |
Hybrid control system |
P1C9E9F |
Hybrid/EV System Reset Stuck Off |
HINT:
- P1CE213 or P1CE292 may be output as a result of the malfunction indicated by the DTCs above.
- The chart above is listed in inspection order of priority.
- Check DTCs that are output at the same time by following the listed order. (The main cause of the malfunction can be determined without performing unnecessary inspections.)
(e) Turn the power switch off.
| B | GO TO DTC CHART (HYBRID CONTROL SYSTEM) |
| C | GO TO DTC CHART (MOTOR GENERATOR CONTROL SYSTEM) |
|
CLEAR DTC
Click here ![]()
|
CHECK DTC OUTPUT (HYBRID CONTROL)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Check if DTCs are output.
Powertrain > Hybrid Control > Trouble CodesResult | Proceed to |
|---|---|
P1CE213 or P1CE292 is output again. |
A |
Neither P1CE213 or P1CE292 is output again. |
B |
HINT:
Check if the same DTC is output.
(e) Turn the power switch off.
| B | GO TO STEP 4 |
|
CHECK INVERTER COVER
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Check if the inverter cover of the inverter with converter assembly is installed correctly. OK: The inverter cover is installed correctly. |
![]() |
| NG | INSTALL PARTS CORRECTLY |
|
CHECK INVERTER COVER
CAUTION:
Be sure to wear insulated gloves.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the inverter cover from the inverter with converter assembly. Click here |
![]() |
(c) Check the condition of the inverter cover interlock. OK: Dirt or foreign matter has not entered the connectors and there is no evidence of contamination. |
|
(d) Install the inverter cover.
| OK | REPLACE INVERTER WITH CONVERTER ASSEMBLY |
| NG | REPLACE INVERTER COVER |
IGB Signal Circuit Short to Auxiliary Battery (P1CFA12)
DESCRIPTION
The hybrid vehicle control ECU monitors the IGB signal received from the certification ECU (smart key ECU assembly). When an error is detected in the IGB signal, this DTC is stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P1CFA12 |
IGB Signal Circuit Short to Auxiliary Battery |
An IGB signal from the hybrid vehicle control ECU is on when the power switch is off. (1 trip detection logic) |
|
Does not come on |
Master Warning Light: Comes on |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
WIRING DIAGRAM
NOTICE:
Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here ![]()
PROCEDURE
CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
Click here ![]()
| NG | CONNECT SECURELY |
|
CHECK CONNECTOR CONNECTION CONDITION (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Check the connector connection condition of the certification ECU (smart key ECU assembly).
Click here ![]()
OK:
The connector is connected securely and there are no contact problems.
| NG | CONNECT SECURELY |
|
CHECK HARNESS AND CONNECTOR (IGB TERMINAL VOLTAGE)
(a) Turn the power switch off.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
| OK | REPLACE HYBRID VEHICLE CONTROL ECU |
|
CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Measure the voltage according to the value(s) in the table below. Standard Voltage:
|
|
(c) Reconnect the G40 certification ECU (smart key ECU assembly) connector.
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off (P33B99F)
DTC SUMMARY
MALFUNCTION DESCRIPTION
The hybrid vehicle control ECU detects malfunctions which prevent the inverter with converter assembly emergency shutdown circuit (HSDN) from shutting down the hybrid control system. Detection is performed when the power switch is turned on (IG) and during the shutdown sequence when the power switch is turned off. If any of the following condition is detected, this DTC will be stored. If the following conditions are not detected, DTC P321E9F will be stored.
- Hybrid vehicle control ECU malfunction
DESCRIPTION
Refer to the description for DTC P321E9F.
Click here ![]()
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P33B99F |
Motor/Generator Shutdown Signal (Hybrid/EV Side) Stuck Off |
When the HV gate shutdown function check is performed (when the power switch is turned from on (READY) to off) and checked at the motor generator control ECU (MG ECU), the shutdown signals sent by the main CPU and sub CPU of the hybrid vehicle control ECU do not match. (1 trip detection logic) |
Hybrid vehicle control ECU |
Does not come on |
Master Warning Light: Comes on |
DTC No. | Data List |
|---|---|
P33B99F |
- |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here ![]()
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (READY) and wait for 30 seconds or more.
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform driving pattern again.
PROCEDURE
REPLACE HYBRID VEHICLE CONTROL ECU
Click here ![]()
| NEXT | END |


