Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range (P06B01C,...,P313487). Internal Control Module EEPROM Data Memory Failure (P062F44). Generator Control Module(EEP
Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range (P06B01C,...,P313487)
DESCRIPTION
The motor generator control ECU (MG ECU), which is built into the inverter with converter assembly, monitors its internal operation and will store DTCs if it detects a malfunction. If any of the following DTCs are output, replace the inverter with converter assembly.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P06B01C |
Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P06D61C |
Generator Control Module Offset Power Circuit Voltage Out of Range |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P0A1A47 |
Generator Control Module Watchdog / Safety μC Failure |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P0A1A49 |
Generator Control Module Internal Electronic Failure |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P1C2A1C |
Generator A/D Converter Circuit Circuit Voltage Out of Range |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P1C2A49 |
Generator A/D Converter Circuit Internal Electronic Failure |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P1C2B1C |
Drive Motor "A" Control Module A/D Converter Circuit Voltage Out of Range |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P1C2B49 |
Drive Motor "A" Control Module A/D Converter Circuit Internal Electronic Failure |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P1C601F |
Generator Control Module Position Sensor REF Power Source Circuit Intermittent |
Motor generator control ECU internal malfunction detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored. (1 trip detection logic) |
Inverter with converter assembly |
Does not come on |
Master Warning Light: Does not come on |
P1C621F |
Generator Control Module Offset Power Circuit Intermittent |
Motor generator control ECU internal malfunction detected when DTC P0C7917, P0D3319, P1C5D19 or P1C5F19 is stored. (1 trip detection logic) |
Inverter with converter assembly |
Does not come on |
Master Warning Light: Does not come on |
P313383 |
Communication Error from Generator to Drive Motor "A" Value of Signal Protection Calculation Incorrect |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P313386 |
Communication Error from Generator to Drive Motor "A" Signal Invalid |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P313387 |
Communication Error from Generator to Drive Motor "A" Missing Message |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P313483 |
Communication Error from Drive Motor "A" to Generator Value of Signal Protection Calculation Incorrect |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P313486 |
Communication Error from Drive Motor "A" to Generator Signal Invalid |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
P313487 |
Communication Error from Drive Motor "A" to Generator Missing Message |
Motor generator control ECU internal malfunction (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
MONITOR DESCRIPTION
The motor generator control ECU monitors its internal operation and will illuminate the MIL and store a DTC if it detects a malfunction.
MONITOR STRATEGY
Related DTCs |
P06B0 (INF P06B01C): Sensor Power Supply "A" Circuit (31V for Drive Motor "A"/Generator) P06D6 (INF P06D61C): Sensor Reference Voltage "F" Circuit (2.5V for Drive Motor "A"/Generator) P0A1A (INF P0A1A47): Generator Control Module P0A1A (INF P0A1A49): Generator Control Module P1C2A (INF P1C2A1C): Generator Control Module A/D Processing P1C2A (INF P1C2A49): Generator Control Module A/D Processing P1C2B (INF P1C2B1C): Drive Motor "A" Control Module A/D Processing P1C2B (INF P1C2B49): Drive Motor "A" Control Module A/D Processing P3133 (INF P313383): Lost Communication With Generator Control Module P3133 (INF P313386): Lost Communication With Generator Control Module P3133 (INF P313387): Lost Communication With Generator Control Module P3134 (INF P313483): Lost Communication With Drive Motor "A" Control Module P3134 (INF P313486): Lost Communication With Drive Motor "A" Control Module P3134 (INF P313487): Lost Communication With Drive Motor "A" Control Module |
Required sensors/components |
Motor generator control ECU |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
Immediately |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Motor generator control ECU |
DTC P06B0 (INF P06B01C) is not detected DTC P06D6 (INF P06D61C) is not detected DTC P0A1A (INF P0A1A47) is not detected DTC P0A1A (INF P0A1A49) is not detected DTC P1C2A (INF P1C2A1C) is not detected DTC P1C2A (INF P1C2A49) is not detected DTC P1C2B (INF P1C2B1C) is not detected DTC P1C2B (INF P1C2B49) is not detected DTC P3133 (INF P313383) is not detected DTC P3133 (INF P313386) is not detected DTC P3133 (INF P313387) is not detected DTC P3134 (INF P313483) is not detected DTC P3134 (INF P313486) is not detected DTC P3134 (INF P313487) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 15 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
REPLACE INVERTER WITH CONVERTER ASSEMBLY
Click here
| NEXT | COMPLETED |
Internal Control Module EEPROM Data Memory Failure (P062F44)
DESCRIPTION
The inverter with converter assembly monitors its internal operation and will store this DTC if it detects a malfunction of its EEPROM.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P062F44 |
Internal Control Module EEPROM Data Memory Failure |
ECU internal malfunction (EEPROM error) (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Does not come on |
MONITOR DESCRIPTION
The motor generator control ECU monitors its internal operation. If the internal operation is malfunctioning, the motor generator control ECU illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
P062F (INF P062F44): Internal Control Module EEPROM (Drive Motor "A" Control Module) |
Required sensors/components |
Motor generator control ECU |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
1 driving cycle |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Motor generator control ECU |
DTC P062F (INF P062F44) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 15 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
REPLACE INVERTER WITH CONVERTER ASSEMBLY
Click here ![]()
| NEXT | COMPLETED |
Generator Control Module(EEPROM Learning Value) Calibration / Parameter Memory Failure (P062F46)
DESCRIPTION
The inverter with converter assembly monitors its internal operation and will store this DTC if it detects a malfunction of its EEPROM.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Warning Indicate |
|---|---|---|---|---|---|
P062F46 |
Generator Control Module(EEPROM Learning Value) Calibration / Parameter Memory Failure |
ECU internal malfunction (EEPROM error) (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning Light: Comes on |
MONITOR DESCRIPTION
The motor generator control ECU monitors its internal operation. If the internal operation is malfunctioning, the motor generator control ECU illuminates the MIL and stores a DTC.
MONITOR STRATEGY
Related DTCs |
P062F (INF P062F46): Internal Control Module EEPROM (Drive Motor "A" Control Module) |
Required sensors/components |
Motor generator control ECU |
Frequency of operation |
Continuous |
Duration |
TMC's intellectual property |
MIL operation |
1 driving cycle |
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
Motor generator control ECU |
DTC P062F (INF P062F46) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
- After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here

- When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

- Connect the Techstream to the DLC3.
- Turn the power switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the power switch off and wait for 2 minutes or more.
- Turn the power switch on (IG) and turn the Techstream on.
- With power switch on (IG) and wait for 15 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
- Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
PROCEDURE
REPLACE INVERTER WITH CONVERTER ASSEMBLY
Click here ![]()
| NEXT | COMPLETED |